- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Thinner 2621 is a thinner for use in various applications.
Click To Jump To Section:
Features & Benefits
- For use with compatible HMG systems.
Suitable for use with the following HMG products:
- HMG AR141 Matt Black
- HMG Chlorinated Rubber
- HMG Hammer Finishes QAD
- HMG QAD Enamel
- HMG HB05 Primer
- HMG HB48 Primer
- HMG High Build Vinyl Primer Finish
- HMG SPS Primer Finish Gloss
- HMG SPS30 Primer Finish
- HMG SPS70 Primer Finish
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
HMG Thinner 2621 | ||||||
Volume Solids: | 0.0% | |||||
VOC Content: | 0.780kgs/ltr | |||||
SG: | - | |||||
Viscosity: | Not determined | |||||
Density: | 0.868 g/cm³ | |||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
Flash Point: | 24°C |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Product Notes
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
HMG Thinner 2621 | ||||||
Form: | According to product specification | |||||
Colour: | According to product specification | |||||
Odour: | Characteristic | |||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | |||||
Melting point/freezing point: | -95°C | |||||
Initial boiling point and boiling range: | 137°C | |||||
Flash Point: | 24°C | |||||
Flammability (solid, gas): | Not applicable | |||||
Ignition temperature: | 430°C | |||||
Decomposition temperature: | Not determined. | |||||
Auto-ignition temperature: | Product is not selfigniting. | |||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
Explosion limits: Lower: | 1 Vol % | |||||
Explosion limits: Upper: | 7.8 Vol % | |||||
Vapour pressure at 20°C: | 9.5 hPa | |||||
Density at 20°C: | 0.868 g/cm³ | |||||
Relative density: | Not determined | |||||
Vapour density: | Not determined | |||||
Evaporation rate: | Not determined | |||||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
Partition coefficient: n-octanol/water: | Not determined | |||||
Viscosity: Dynamic at 20°C: | Not determined | |||||
Viscosity: Kinematic: | Not determined | |||||
Solvent content: Organic solvents: | 100.0% | |||||
Solids content: | 0.0% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
Data sheet
- Manufacturer
- HMG Paints Limited
- Density
- 0.868 g/cm³
- Solids by Volume
- 0.0%
- VOC
- 0.780kgs/ltr
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- Size
- 1L, 5L & 25L
- UN Number
- 1263
- Product Usage Type
- Thinner
- Categorised As
- Accessories > Thinners
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Thinner 2621 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG QAD Enamel
HMG QAD Enamel is an industrial, durable, high gloss, tough alkyd for use on spray applied steel, railings, exterior furniture and fencing plus other suitable prepared metals. Quick drying - touch dry in 30 minutes Coverage: 11-12m² per litre at 20 microns dft, 10-12 m² per litre at 55 microns dft Can be applied to mild, galvanised and...
HMG Chlorinated Rubber
HMG Chlorinated Rubber is a versatile, high build, easy to apply, single pack chlorinated rubber based paint. It gives excellent durability combined with good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms. Available in 3,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours Versatile High...
HMG AR141 Matt Black
HMG AR141 Matt Black is an air dying silicone based paint specifically formulated to enable the dried film to tolerate high temperatures up to 300ºC. The full physical properties are achieved after baking at temperatures above 220ºC (at this temperature the free silicones in the system auto cross link) At temperatures of up to 300ºC...
HMG HB05 Primer
HMG HB05 Primer is an alkyd based, high build primer offering outstanding adhesion, moisture resistance and corrosion protection due to incorporation of modified zinc phosphate. Designed for airless or conventional application for structural steelwork, chassis, steel fabrication etc. It is easy to apply without fear of runs or sags at...
HMG HB48 Primer
HMG HB48 Primer is an alkyd based, quick drying primer offering outstanding adhesion, moisture resistance and corrosion protection due to incorporation of modified Zinc Phosphate. Suitable for structural steelwork, chassis, steel fabrication, mild steel, shot blasted steel, aluminium & galvanised steel Easy to apply without fear of...
HMG SPS70 Primer Finish
HMG SPS70 Primer Finish is a quick drying, durable, anti-corrosive, single protection system providing hard wearing, tough matt, semi-gloss or full gloss finish - Keeps equipment looking new for longer. Application direct to metal with wet-on-wet application. For professional use Quick-drying - touch dry in 30 mins, hard dry after 6...
HMG SPS30 Primer Finish
HMG SPS30 Primer Finish is a quick drying SPS (Single Protection System) single coat finish offering excellent performance. Provided with a sheen level of 30% finish Hard dry in as little as 60 minutes at 20℃ Touch dry in 30 mins at 20℃ Coverage up to 8-10m2 per litre Flashpoint: 24℃ Available in 5,000+ colours from RAL, NCS, and...
HMG SPS Primer Finish Gloss
HMG SPS Primer Finish Gloss is a quick drying SPS, durable, anti-corrosive, single protection system providing hard wearing, tough gloss finish. Application direct to metal with wet-on-wet application. Keeps equipment looking new for longer. For professional use Quick drying - touch dry in 30 mins at 20°C, hard dry in 6 hours at 20°C...
HMG High Build Vinyl Primer Finish
HMG High Build Vinyl Primer Finish is a high build anti corrosive vinyl primer finish. Excellent adhesion Corrosion protection to mild steel, aluminium, stainless steel and galvanised substrates Available in 5,000+ colours from RAL, NCS, and British Standard Also available as an aerosol, please see HMG High Build Vinyl Primer Finish...