- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Hardener 9075 is a 2K Polyamide Hardener for use in HMG Epoxy Primer EP3S.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
2-Pack System Details | |||||
---|---|---|---|---|---|
Base (Part 1) | HMG Epoxy Primer EP2 | ||||
Hardener (Part 2) | HMG Hardener 9075 |
- Part two of a two part system.
HMG Hardener 9075 is a 2K Polyamide Hardener for use in HMG Epoxy Primer EP3S.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Epoxy Primer EP2.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Part two of a two part system.
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
HMG Hardener 9075 | ||||||
Volume Solids: | 35.9% | |||||
VOC Content: | 0.580kgs/ltr | |||||
SG: | - | |||||
Viscosity: | Not determined | |||||
Density: | 0.917 g/cm³ | |||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
Pot Life: | - | |||||
Flash Point: | 24°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Application Method | n/a | n/a |
Coverage: -
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | n/a |
Dry To Recoat: | n/a |
Fully Cured: | n/a |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Application | |||||
Mixing Ratio: | Mixing instructions appear on base component. | ||||
Thinner Options: | - | ||||
Viscosity: | - | ||||
Spray Gun Setup: | - | ||||
Number Of Coats (Guide Only): | - | ||||
Flash Off: | - |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
HMG Hardener 9075 | ||||||
Form: | According to product specification | |||||
Colour: | According to product specification | |||||
Odour: | Characteristic | |||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | |||||
Melting point/freezing point: | Undetermined | |||||
Initial boiling point and boiling range: | 136°C | |||||
Flash Point: | 24°C | |||||
Flammability (solid, gas): | Not applicable | |||||
Ignition temperature: | 430°C | |||||
Decomposition temperature: | Not determined. | |||||
Auto-ignition temperature: | Product is not selfigniting. | |||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
Explosion limits: Lower: | 0.7 Vol % | |||||
Explosion limits: Upper: | 7.5 Vol % | |||||
Vapour pressure at 20°C: | 6.7 hPa | |||||
Density at 20°C: | 0.917 g/cm³ | |||||
Relative density: | Not determined | |||||
Vapour density: | Not determined | |||||
Evaporation rate: | Not determined | |||||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
Partition coefficient: n-octanol/water: | Not determined | |||||
Viscosity: Dynamic at 20°C: | Not determined | |||||
Viscosity: Kinematic: | 30 s (DIN 53211/4) | |||||
Solvent content: Organic solvents: | 64.1% | |||||
Solids content: | 35.9% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
Data sheet
- Manufacturer
- HMG Paints Limited
- Single, Two or Three Pack
- Single
- Solids by Volume
- 35.9%
- VOC
- 0.580kgs/ltr
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- UN Number
- 1263
- Base Type
- Polyamide
- Product Usage Type
- Hardener
- Categorised As
- Accessories > Hardeners & Activators
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Hardener 9075 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT