- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Solvent-free varnish used for dust binding, priming and topcoating especially where solventless and odourless products are needed. The lacquer can be used for patching when filled with sand.
- Good resistance against abrasion, oils and grease.
- Also for dust binding and priming of new and old concrete floors prior to laying Temafloor epoxy coatings and screeds; especially where solventless and odourless products are needed.
- Can be used as a finishing varnish in the Mosaic flooring system.
- Filled with sand also suitable for patching of concrete floors.
- Used as a binder for Temafloor 4000 Compact troweling screed.
Tikkurila Temafloor 210 Clear is a solvent-free varnish used for dust binding, priming and topcoating especially where solventless and odourless products are needed. The lacquer can be used for patching when filled with sand.
Temafloor 210 Clear is widely used and has the highest quality. It has good resistance against abrasion, oils and grease. Varnish forms glossy, smooth and non-yellowing finish. Temafloor 210 Clear can be applied with mosaic flakes as a top lacquer.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Technical Data
- Surface Preparation
- Recommended Topcoats
- Application Conditions
- Mixing Components
- Application
- VOC
- Health And Safety
Features & Benefits
- Good resistance against abrasion, oils and grease.
- Also for dust binding and priming of new and old concrete floors prior to laying Temafloor epoxy coatings and screeds; especially where solventless and odourless products are needed.
- Can be used as a finishing varnish in the Mosaic flooring system.
- Filled with sand also suitable for patching of concrete floors.
- Used as a binder for Temafloor 4000 Compact troweling screed.
- Suitable also for topcoating of concrete floors indoors.
Technical Data
- Volume Solids: Approx. 100%
- Specific Gravity: 1.1 kg / litre (mixture)
- Pot Life (23℃): Approx. 30 minutes after mixing, on substrate
Practical Coverage:
Coverage on concrete floors is on average:
- Primer: 5 – 8 m²/l
- Topcoat: 6 – 10 m²/l
Practical coverage depends on the porosity and evenness of the substrate and on the application method.
Mixing Ratio:
- Base: 2 parts by volume Temafloor 210 Clear
- Hardener: 1 part by volume 008 4431
Drying Time (23℃)
- Dust dry after 6 hours
- Recoatable after 16 - 24 hours
- Light trucking after 24 hours
- Fully cured after 7 days
Surface Preparation
New Concrete
- Remove laitance by power grinding or hydrochloric acid etching.
- Choose the method best suited for the premises.
- After grinding remove dust carefully with a vacuum cleaner.
- Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water).
- Rinse with plenty of water.
- Dry the surface.
Old Concrete
- Remove all grease, oil, chemicals and other impurities by Maalipesu detergent.
- Remove old peeling paint layer by grinding.
- Choose the method best suited for the premises.
- Clean out pot-holes removing all loose friable material.
- Open cracks with e.g. an abrasive tool.
- Remove loose material and dust.
If cementitious screed is used, check compatibility with the levelling screed manufacturer.
Application Conditions
- The relative humidity of the concrete should not exceed 97%.
- The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying.
- Relative humidity of air should not exceed 80%.
Note! There is a natural tendency of this coating to chalk, discolor or yellow unevenly. It is recommended to use polyurethane topcoat when there are high aesthetical requirements on colour appearance.
Mixing Components
- First stir base and hardener separately.
- Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes to get homogenous mixture) by using a low speed industrial hand drill with a paddle.
- Use power mixer for mixing.
- Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Application
Priming:
- Prime using 30–50% thinned Temafloor 200 Primer epoxy varnish.
- Pour the varnish mixture onto the floor and apply as much as is needed to impregnate the concrete surface.
- If necessary, repeat priming to get a non-porous surface. A porous priming coat will result in holes and air bubbles in the finished coating.
- Subsequent treatment can becarried out after 2 hours using "wet-on-wet" technique.
Patching:
- Prime using about 30% thinned Temafloor 210 Clear epoxy varnish.
- Pour the varnish mixture onto the floor and apply as much as is needed to impregnate the concrete surface.
- If necessary, repeat priming to get a non-porous surface.
- A porous priming coat will result in holes and air bubbles in the finished coating.
- Subsequent treatment can be carried out after 2 hours using "wet-on-wet" technique.
- Note! Concrete surface should always be primed before patching.
Topcoating:
- Overcoating should be done within 16–24 hrs after priming.
- If the primed surface is not overcoated within 24 hrs, it should be abraded.
- For finishing Temafloor 210 Clear epoxy varnish may be thinned up to 10%.
- Pour the mixture onto the floor and apply it with a trowel and level with a roller.
- Note! Add the remaining mixture to the next batch of the product, do not scrape it out of the container onto the floor.
Thinner/Cleaning
Thinner
Cleaning Of Equipment
VOC
VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor 210 Clear: max. VOC < 500 g/l
Health And Safety
Reacton To Fire: BFL-s1 according to EN 13501-1
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
For industrial and professional use only.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Data sheet
- For Use By
- Professional Use
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- Base: 2 parts by volume Temafloor 210 Clear - Hardener: 1 part by volume 008 4431
- Coverage
- Primer: 5 – 8 m²/l - Topcoat: 6 – 10 m²/l
- Recommended Thinner/Cleaner
- Thinner 1029
- Solids by Volume
- Approx. 100%
- Finish
- Gloss
- Dry to Recoat (at 23°C)
- 16 - 24 hours
- Touch Dry (at 23°C)
- 6 hours
- Fully Cured (at 23°C)
- After 7 days
- Pot Life
- Approx. 30 minutes after mixing, on substrate.
- Base Type
- Solvent-Free
- Suitable For Use On
- Concrete Floors
- Finish
- Gloss
- Components
- 2K
- Usages
- Low Odour
- Product Usage Type
- Sealer
- Product Usage Type
- Binder
- Product Range
- Temafloor
- Colour Family
- Clear
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tikkurila Temafloor 210 Clear is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Tikkurila Temafloor 200 Primer
2-component solvent-free epoxy varnish. It gives good adhesion for Temafloor coatings and screeds and dries fast. Short overcoating time enables whole system application in one day. Thinned Temafloor 200 Primer penetrates well into the pores of the concrete sealing the surface and giving good adhesion for coatings and screeds Mixed with...
Tikkurila Thinner 1029
Tikkurila Thinner 1029 is a thinner for ethyl zinc silicate paints and solvent-free epoxy paints.