- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2 component solvent-free varnish used for priming of new and old concrete floors, especially where solventless and odourless products are needed.
- For priming of new and old concrete floors prior to laying Temafloor coatings and screeds.
- Good resistance against oil and grease.
- Suitable for priming of damp concrete (relative humidity of the concrete over 97%) surfaces.
Tikkurila Temafloor 220W Primer is a two component solvent-free varnish used for priming of new and old concrete floors, especially where solventless and odourless products are needed.
Temafloor 220W Primer is mostly used for damp concrete with relative humidity of the concrete over 97%, when curing process is still in progress. Thus, it makes construction works ready faster.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Technical Data
- Surface Preparation
- Recommended Topcoats
- Application Conditions
- Mixing Components
- Application
- VOC
- Health And Safety
Features & Benefits
- For priming of new and old concrete floors prior to laying Temafloor coatings and screeds.
- Good resistance against oil and grease.
- Suitable for priming of damp concrete (relative humidity of the concrete over 97%) surfaces.
Technical Data
- Volume Solids: Approx. 100%
- Specific Gravity: 1.1 kg / litre (mixture).
- Pot Life (23℃): Approx. 30 minutes after mixing, on substrate.
Practical Coverage:
Coverage on concrete floors is on the average 6–10 m²/l.
Practical coverage depends on the porosity and evenness of the substrate and on the application method.
Mixing Ratio:
- Base: 2 parts by volume Temafloor 220W Primer
- Hardener: 1 part by volume 008 4370
Drying Time (23℃)
- Dust dry after 6 hours
- Recoatable after 9 hours - 3 days
- Fully cured after 7 days
At lower temperature the drying will last longer.
Surface Preparation
New Concrete
- Remove laitance by power grinding or hydrochloric acid etching.
- Choose the method best suited for the premises.
- After grinding remove dust carefully with a vacuum cleaner.
- Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water).
- Rinse with plenty of water.
- Dry the surface.
Old Concrete
- Remove all grease, oil, chemicals and other impurities by Maalipesu detergent.
- Remove old peeling paint layer by grinding.
- Choose the method best suited for the premises.
- Clean out pot-holes removing all loose friable material.
- Open cracks with e.g. an abrasive tool.
- Remove loose material and dust.
If cementitious screed is used, check compatibility with the levelling screed manufacturer.
Application Conditions
- The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying.
- Relative humidity of air should not exceed 80%.
Note! There is a natural tendency of this coating to chalk, discolor or yellow unevenly. It is recommended to use polyurethane topcoat when there are high aesthetical requirements on colour appearance.
Mixing Components
- First stir base and hardener separately.
- Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes to get homogenous mixture) by using a low speed industrial hand drill with a paddle.
- Use power mixer for mixing.
- Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Application
Priming:
- Prime using 30–50% thinned Temafloor 220W Primer epoxy varnish.
- Pour the varnish mixture onto the floor and apply as much as is needed to impregnate the concrete surface.
- If necessary, repeat priming after about 9 hours to get a non-porous surface.
- A porous priming coat will result in holes and air bubbles in the finished coating.
- Subsequent treatment can be carried out after 2 hours using "wet-on-wet" technique.
Patching:
- Patch pot-holes and cracks with a mixture of unthinned Temafloor 220W Primer epoxy varnish and dry, clean sand.
- Mixing ratio e.g. 1 part by volume of varnish mixture and 1– 2 parts by volume of sand of grain size 0.1–0.6 mm
- Sand the patched areas beforeovercoating, if necessary.
- Note! Concrete surface should always be primed before patching.
Thinner/Cleaning
Thinner:
Cleaning Of Equipment:
Thinner 006 1029 (or Thinner 006 1031)
VOC
VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor 220W Primer: max. VOC < 500 g/l
Health And Safety
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
For industrial and professional use only.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Data sheet
- For Use By
- Professional Use
- Sheen
- Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 15L
- Mixing Ratio
- Base: 2 parts by volume Temafloor 220W Primer - Hardener: 1 part by volume 008 4370
- Coverage
- 6–10 m²/l
- Density
- 1,15 g/cm³
- Density
- Hardener: 1.03 g/cm³
- Density
- Thinner: 0.86 g/cm³
- Solids by Volume
- approx. 100%
- Finish
- Gloss
- Size
- 15L
- UN Number
- UN3082
- UN Number
- Hardener: UN2735
- UN Number
- Thinner: UN1263
- Dry to Recoat (at 23°C)
- 9 hours - 3 days
- Touch Dry (at 23°C)
- 6 hours
- Fully Cured (at 23°C)
- 7 days
- Base Type
- Solvent-Free
- Suitable For Use On
- Concrete Floors
- Finish
- Gloss
- Components
- 2K
- Usages
- Damp Tolerant
- Product Usage Type
- Primer
- Product Usage Type
- Binder
- Product Range
- Temafloor
- Colour Family
- Clear
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tikkurila Temafloor 220W Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Tikkurila Thinner 1029
Tikkurila Thinner 1029 is a thinner for ethyl zinc silicate paints and solvent-free epoxy paints.
Tikkurila Thinner 1031
Tikkurila Thinner 1031 is a thinner for epoxy paints, silicone paints, polyvinylbutyral paints, 2-component zinc rich paints and epoxy shop primers.