- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2-component solvent-free epoxy varnish. An excellent product for dust binding and priming of new and old concrete floors, especially where solventless and odourless products are needed. The lacquer can be used for patching when filled with sand.
- Used as a binder for Temafloor 4000 troweling screed and epoxy concrete.
- Used also as a topcoat on top of Temafloor coatings and screeds.
- Filled with sand also suitable for patching of concrete floors.
- Suitable for dust binding and priming of new and old concrete floors under Temafloor coatings.
Tikkurila Temafloor 400 is a two-component solvent-free epoxy varnish. An excellent product for dust binding and priming of new and old concrete floors, especially where solventless and odourless products are needed. The lacquer can be used for patching when filled with sand.
This lacquer is a main component of Temafloor 4000 grinding screed. Temafloor 400 also can be apply on the top of Temafloor coatings and screeds. It can be used with mosaic flakes as a top lacquer to increase anti-slip properties
Quick Links - Click To Jump To Section:
- Features & Benefits
- Technical Data
- Surface Preparation
- Recommended Topcoats
- Application Conditions
- Mixing Components
- Application
- VOC
- Health And Safety
Features & Benefits
- Used as a binder for Temafloor 4000 troweling screed and epoxy concrete.
- Used also as a topcoat on top of Temafloor coatings and screeds.
- Filled with sand also suitable for patching of concrete floors.
- Suitable for dust binding and priming of new and old concrete floors under Temafloor coatings.
Technical Data
Technical Data | ||||||
---|---|---|---|---|---|---|
Tikkurila Temafloor 400 | ||||||
Volume Solids: | approx. 100% | |||||
SG: | 1.1 kg/l (mixture) | |||||
Viscosity: | n/a | |||||
Density: | 1.12 g/cm³ - Hardener: 1.01 g/cm³ | |||||
Storage Conditions: | Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10). Keep container tightly closed. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Recommended storage temperature is +5°C - +25°C | |||||
Shelf Life: | None | |||||
Pot Life: | Approx. 30 minutes after mixing, on substrate. | |||||
Flash Point: | >100˚C | |||||
Coverage (on concrete floors): | Primer 5–8 m²/l - Topcoat 6–10 m²/l |
Practical coverage depends on the porosity and evenness of the substrate and on the application method.
Drying Times At 23°C | |
---|---|
Dust Dry: | After 6 hours |
Recoatable: | After 16 - 24 hours |
Fully Cured: | After 7 days |
Surface Preparation
New Concrete
- Remove laitance by power grinding or hydrochloric acid etching.
- Choose the method best suited for the premises.
- After grinding remove dust carefully with a vacuum cleaner.
- Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water).
- Rinse with plenty of water.
- Dry the surface.
Old Concrete
- Remove all grease, oil, chemicals and other impurities by Maalipesu detergent.
- Remove old peeling paint layer by grinding.
- Choose the method best suited for the premises.
- Clean out pot-holes removing all loose friable material.
- Open cracks with e.g. an abrasive tool.
- Remove loose material and dust.
If cementitious screed is used, check compatibility with the levelling screed manufacturer.
Application Conditions
- The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying.
- Relative humidity of air should not exceed 80%.
- Sunlight will affect on the shade and the gloss of the varnish in the long run.
Note! There is a natural tendency of this coating to chalk, discolor or yellow unevenly. It is recommended to use polyurethane topcoat when there are high aesthetical requirements on colour appearance
Mixing Components
Mixing Ratio | ||
---|---|---|
Base: | 3 parts by volume | Temafloor 400 |
Hardener: | 1 part by volume | 008 4408 |
- First stir base and hardener separately.
- Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes to get homogenous mixture) by using a low speed industrial hand drill with a paddle.
- Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Application
Priming:
- Prime using about 30% thinned Temafloor 400 epoxy varnish.
- Pour the varnish onto the floor and apply as much as is needed to impregnate the concrete surface.
- If necessary, repeat priming to get a non-porous surface.
- A porous priming coat will result in holes and air bubbles in the finished coating.
- Subsequent treatment can be carried out after 2 hours using "wet-on-wet" technique.
Patching:
- Patch pot-holes and cracks with a mixture of unthinned Temafloor 400 epoxy varnish and dry, clean sand.
- Mixing ratio e.g. 1 part by volume of varnish mixture and 1–2 parts by volume of sand of grain size 0.1–0.6 mm.
- Sand the patched areas before overcoating, if necessary.
- Note! Concrete surface should always be primed before patching.
Thinner/Cleaning
Thinner:
Cleaning Of Equipment:
VOC
VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor 400: max. VOC < 500 g/l
Health And Safety
Reaction to fire: BFL-s1 according to standard EN 13501-1.
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
For industrial and professional use only.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Data sheet
- Manufacturer
- Tikkurila
- For Use By
- Professional Use
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- Base: 3 parts by volume - Temafloor 400
- Mixing Ratio
- Hardener: 1 part by volume - 008 4408
- Recommended Thinner/Cleaner
- Thinner 1029
- Density
- 1.12 g/cm³ - Hardener: 1.01 g/cm³
- Solids by Volume
- approx. 100%
- UN Number
- UN3082
- UN Number
- Hardener: UN2735
- Dry to Recoat (at 23°C)
- After 16 - 24 hours
- Touch Dry (at 23°C)
- After 6 hours
- Fully Cured (at 23°C)
- After 7 days
- Pot Life
- Approx. 30 minutes after mixing, on substrate.
- Base Type
- Solvent-Free
- Suitable For Use On
- Concrete Floors
- Finish
- Gloss
- Components
- 2K
- Usages
- Low Odour
- Product Usage Type
- Primer
- Product Usage Type
- Binder
- Product Range
- Temafloor
- Colour Family
- Clear
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tikkurila Temafloor 400 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Tikkurila Temafloor P300
2-component, solvent-free, self-levelling epoxy coating in 4,000+ colours for new and old concrete floors exposed to heavy mechanical and chemical stress in industrial and storage facilities, withstanding water, oils, greases, chemicals and dilute solutions of non-oxidizing acids, alkali and salt solutions. Good resistance to abrasion...
Tikkurila Temafloor PU
Solvent-free, elastic two-component polyurethane coating. For new and old concrete and asphalt floors exposed to mechanical and chemical stress. Withstands water, oils, greases, chemicals and dilute solutions of non-oxidizing acids, alkali and salt solutions. Resists only temporary splashes of oxidizing acids and bleaching chemicals....
Tikkurila Thinner 1029
Tikkurila Thinner 1029 is a thinner for ethyl zinc silicate paints and solvent-free epoxy paints.