- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta Hi-Dur AD100 Finish is a fast drying, modified alkyd gloss finish for steel plant and equipment. It is designed for spray application with fast drying properties which allows quick turnaround times.
- Where a fast drying gloss finish is required
- Fast drying minimises dust contamination to give a durable high gloss finish
- Hard Dry in 5hrs at 23°C
- For use as a finish coat over a range of single pack and two pack primers
- Wide colour range of over 350+ RAL and BS shades to suit all finishing shades
- Suitable for agricultural and earth moving equipment, metal fabrications and general use
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartAxalta Hi-Dur AD100 Finish is a fast drying, modified alkyd gloss finish for steel plant and equipment. It is designed for spray application with fast drying properties for quick turnaround times.
Suitable for agricultural and earth moving equipment, metal fabrications and general use. Available in a wide colour range of over 350+ RAL and BS shades.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected].
Quick Links - Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- For steel plant and equipment
- Modified alkyd gloss finish
- For spray application
- Suitable for agricultural and earth moving equipment, metal fabrications and general use
- Wide colour range of over 350+ RAL and BS shades to suit all finishing shades
- Fast drying minimises dust contamination to give a durable high gloss finish
- Hard Dry in 5hrs at 23°C
- For use as a finish coat over a range of single pack and two pack primers
Product Specification
Technical Data | |
---|---|
Axalta Hi-Dur AD100 Finish | |
Volume Solids | 39 ± 2% (varies with colour) |
VOC Content | 520 + 30 g/litre (varies with colour) |
SG | 0.99 kg/lt (varies with colour) |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | 23-60°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Typical | 35 µm | 90 µm | 11.1 m2/litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times
Product Data | ||||
---|---|---|---|---|
Applied to 35 microns DFT | 10℃ | 23℃ | 35℃ | |
Dust Free | 1 hr | 25 min | 15 min | |
Hard Dry | 8 hr | 5 hr | 3 hr | |
Overcoating | Minimum* | 2 to 8 hr | 1 to 4 hr | 1 to 4 hr |
Do Not Overcoat | 8 to 36 hr | 4 to 24 hr | 4 to 24 hr | |
Maximum | Indefinite if clean and sound | |||
*See Product Notes. Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- This product is a finish coat and should be applied over an appropriate primer and/or intermediate coat, please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected] for advice
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination
Mixing
- Must be mixed thoroughly by using a mechanical agitator before use
- Agitate periodically to ensure paint remains homogeneous
Thinner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing
- Do not apply when rain, mist, sleet or snow are imminent
- During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
- Paint temperature should ideally be at a minimum of 15ºC
Application Methods
- Airless Spray: Output fluid pressure at tip 2000 psi min., Tip Size 11-15 thou (0.28-0.38 mm)
- Conventional spray: Typical air atomising pressure 50-60 psi
- Application by brush is recommended for touch up only as product is very fast drying. For brush application, ViterLac ABV is recommended
- Dependent on temperature, the material may require thinning up to 5% with TH120 Thinner
Product Notes
- Overcoating: This product goes through an intermediate period where wrinkling by subsequent applications may occur. Overcoat before the lowest time shown, or leave until after the highest time shown, in order to allow adequate through drying
- Do not apply over white spirit based products. The compatibility of overcoating products should be confirmed prior to application
- Not recommended for immersion
- For best opacity use a primer or undercoat of a suitable shade
Health & Safety
- Containers are provided with safety labels which should be observed
- Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Axalta
- For Use On
- Steel
- Application Method
- Airless Spray, Spray
- Sheen
- Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Minimum Applied Thickness
- 35 µm
- Maximum Applied Thickness
- 90 µm
- Key Features
- Fast Drying
- Touch Dry (at 20°C)
- 25 mins
- Coverage
- 11.1 m²/litre
- Solids by Volume
- 39 ± 2% (varies with colour)
- VOC
- 520 + 30 g/litre (varies with colour)
- Shelf Life (from date of manufacture)
- 12 months
- UN Number
- UN1263
- Dry to Recoat (at 23°C)
- 1-4hr @ 23°C
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal Fabrications
- Suitable For Use On
- Agricultural Equipment
- Suitable For Use On
- Earth Moving Equipment
- Suitable For Use On
- General Use
- Finish
- High Gloss
- Application Method
- Spray
- Usages
- Atmospheric
- Product Usage Type
- Topcoat
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Dark
- Colour Family
- Grey
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 25 mins
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta Hi-Dur AD100 Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta Thinner Fast Industrial (TH120)
Axalta Thinner Fast Industrial TH120 (formerly called No.4 Thinner), for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray Can also be used for the cleaning of some...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...