- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Interplus 4103 Clean Cons, a water-based rust remover / cleaner gel designed to remove light to medium rust deposits from a variety of surfaces. A quick, cost-effective and eco-friendly alternative to sandblasting, acid washing or high-pressure water blasting, Interplus 4103 Clean Cons is a concentrated fluid, excellent for cleaning closed systems or the inside of pipes.
- Can be used in offshore environments and drinking water systems
- The perfect solution for surface preparation and the removal of corrosion damage, calcium, salts, humus and magnetite from stainless steel and aluminum structures
- Suitable for cleaning pipe systems, coolers, heat exchangers etc., or for use in dip tray
- Single component
- 100% biological degradable
- Free from toxins
- Conforms to the yellow classification of the Harmonised Offshore Chemical Notification Format (HOCNF)
- Please Note: This product is made to order with an extended lead time of 6 weeks +
Description
A cost-effective, eco-friendly alternative to traditional rust removal, Interplus 4103 Clean Cons is a concentrated fluid, excellent for cleaning closed systems or the inside of pipes.
The new Interplus 4100 range provides the perfect solution for surface preparation and the removal of corrosion damage, calcium, salts, humus and magnetite from stainless steel and aluminum structures. The result is a quick, cost-effective and eco-friendly alternative to sandblasting, acid washing or high-pressure water blasting.
Many different environments can create challenging conditions for metal substrates, causing corrosion and a wide range of surface imperfections. These imperfections can be equally challenging to remove, as these substrates are often hard to reach and non-bio-degradable chemicals cannot be used. The Interplus 4100 range has the answer to convenient and cost-effective surface preparation, with the following features and benefits:
- Easy and time-saving application via normal high-pressure pump
- Provides gel and liquid-based solutions suitable for a range of surfaces
- Can be used in offshore environments and drinking water systems
- Suitable for steel, stainless steel, aluminum, plastic and polyester substrates
The full range is compliant with HOCNF (Harmonised Offshore Chemical Notification Format) and contains only ingredients from the PLONOR (Pose Little Or No Risk) list of environmentally safe chemicals. Each product is 100% biodegradable and 100% toxin free, making for a safe and sustainable solution to rust removal and surface preparation.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Practical Information
- Regulatory Data
- Surface Preperation
- Application
- Product Characteristics
- Systems Compatibility
Features & Benefits
- Single component
- Water-based rust remover / cleaner gel
- 100% biological degradable
- Free from toxins
- Conforms to the yellow classification of the Harmonised Offshore Chemical Notification Format (HOCNF)
- Designed to remove light to medium rust deposits from a variety of surfaces
- Effective for removal of corrosion on stainless steel structures and aluminium
- Can be used as an alternative to:
- Traditional sandblasting
- Ultra-high pressure water blasting
- Power tool methods
Practical Information
| Data | |
|---|---|
| Colour | Yellow |
| Gloss Level | Not applicable |
| Practical Coverage | Allow appropriate loss factors |
| Drying Time | Not applicable |
Regulatory Data
| Data | ||
|---|---|---|
| Flash Point (Typical) | 61°C (142°F) | |
| Product Weight | 1.142 kg/l (9.5 lb/gal) | |
| VOC | 0g/kg | EU Solvent Emissions Directive (Council Directive 2010/75/EU) |
Surface Preperation
Prior to application of Interplus 4103 Clean Cons, any loose rust deposits should be removed to aid penetration of the product. Surfaces not to be treated should be masked and protected with polyethylene. A strong ground sheet should be used to contain residue, product and rinse water. For further details, contact our technical team on 0113 2455450 (option 2) or send a message to [email protected].
Galvanised surfaces can be affected by Interplus 4103 Clean Cons; these areas should be covered. Use of Interplus 4103 Clean Cons on GRP will cause discoloration of the surface.
Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.
Application Conditions
Optimal working temperature range is 8 - 50°C (46 - 122°F). Interplus 4103 Clean Cons can be used at temperatures as low as 2°C (36°F) and a maximum of 60°C (140°F), but a lower level of performance should be expected.
For best results, it is advised to suitably cover the application area to reduce the effect of wind, rain and intense sunlight.
Application
| Data | ||
|---|---|---|
| Mixing | Mixing should not normally be required but if separation has occurred the product should be hand mixed until homogeneous. | |
| Mix Ratio | Depends on the level of contamination present: | |
| High contamination 50% water | ||
| Medium contamination 70% water | ||
| Low contamination 90% water | ||
| It is recommended that a small area is tested in order to confirm the level of dilution required. | ||
| Thinner | Clean potable water | |
| Cleaner | Clean potable water | |
| Work Stoppages | Product containers should be resealed to prevent drying out of the product. | |
| Clean Up | Clean equipment immediately after use with water. Dispose of washing in accordance with local environmental legislation. Neutralising and dilution with water may be required to meet local waste or sewage disposal requirements. Spills should be contained and disposed of under the same requirements. | |
| Removal | High pressure water wash and/or steam cleaners improve removal rates and reduce water usage. Pressure greater than 4000 p.s.i. is advised for large areas and to aid removal of alkaline salts from steel substrates. Cleaned surfaces should be repainted as quickly as possible to prevent reoxidation. | |
Product Characteristics
Interplus 4103 Clean Cons will take 4 - 24 hours to take effect. This is dependent on the type of surface and on the temperature.
When applying Interplus 4103 Clean Cons in confined spaces ensure adequate ventilation.
Interplus 4103 Clean Cons must be protected from freezing at all times during storage.
Systems Compatibility
To ensure good overcoating of approved maintenance primers, it is important that the treated surface is free from all residue contamination and a thorough rinsing and wash down has been undertaken.
The surface should be clean and dry prior to overcoating with approved primers.
The following primers are approved for application direct to Interplus 4103 Clean Cons treated surfaces:
Product Details
5151-862712
Data sheet
- Manufacturer
- International
- Water / Solvent Based
- Water
- For Use On
- steel, stainless steel, aluminium, plastic, polyester
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Single
- Pack Size
- 25L
- Base Type
- Water
- Suitable For Use On
- Stainless Steel
- Suitable For Use On
- Steel
- Suitable For Use On
- Polyester
- Suitable For Use On
- Plastic
- Suitable For Use On
- Aluminium
- Product Usage Type
- Cleaner
- Product Range
- Interplus
- Colour Family
- Yellow
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
International Interplus 4103 Clean Cons is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
International Interplus 356
International Interplus 356 is a low VOC, two component, internally flexibilised, high build, low temperature curing (down to -5°C, 23°F), surface tolerant epoxy primer, metallic pigmented with aluminium and lamellar micaceous iron oxide for increased corrosion resistance. A high performance maintenance coating for use on a wide variety of...
Price
£131.77
(incl. VAT)
In Stock and Available for Delivery
International Interseal 670HS
International Interseal 670HS is a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating, for application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. 4,800+ colours, inc. RAL, RAL Design...
Price
£179.76
(incl. VAT)
In Stock and Available for Delivery
International Interzone 954
2 component, low VOC, high solids, modified epoxy barrier coat in 4,800+ colours designed for use in offshore splashzone maintenance, where its continued cure under immersed conditions makes it ideal for coping with tidal movements and surges. May be applied to reoxidised and slightly damp surfaces. A high film build, high solids, abrasion...
Price
£166.51
(incl. VAT)
In Stock and Available for Delivery
International Interplus 4101 Clean Gel
Interplus 4101 Clean Gel, a water-based rust remover / cleaner gel designed to remove light to medium rust deposits from a variety of surfaces. A quick, cost-effective and eco-friendly alternative to sandblasting, acid washing or high-pressure water blasting, Interplus 4101 Clean Gel has a thick consistency and sticks to surfaces, making it...
Price
£1386.11
(incl. VAT)
In Stock and Available for Delivery