Follow us on:

International Interbond 808

International Interbond 808

KRA853/A20LT KRA850/A20LT
INT5213

International Interbond 808 a two-component high performance epoxy coating for use in water ballast tanks, cofferdams, void spaces, wet spaces, bilges and crude oil tanks.

  • Light colour
  • Tar free
  • DNV/Marintek B-1 classification
  • Surface tolerant/damp tolerant
  • Short time to immersion
  • Low VOC content
  • IMO PSPC compliant

Colour
Size
£726.73(incl. VAT)
£605.61(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

International Interbond 808 a two-component high performance epoxy coating for use in water ballast tanks, cofferdams, void spaces, wet spaces, bilges and crude oil tanks.

Can be applied as a one or two coat system over grit blasted, mechanically prepared shop primer, hydroblasted or mechanically cleaned surfaces.



Quick Links - Click To Jump To Section:




Features & Benefits


  • Light colour
  • Tar free
  • DNV/Marintek B-1 classification
  • Surface tolerant/damp tolerant
  • Short time to immersion
  • Low VOC content
  • IMO PSPC compliant



Product Details


Technial Data
Intended Uses: For use at Maintenance & Repair or On Board Maintenance
Volume Solids: 82% ±2% (ISO 3233:1998)
Typical Thickness: 300 microns dry (366 microns wet)
Theoretical Coverage: 2.73 m²/litre at 300 microns dft, allow appropriate loss factors
Flash Point:

Part A 32°C

Part B 58°C

Mixed 33°C

Induction Period: Not required
VOC: 220 g/lt
Shelf Life: 12 months at 25°C



Drying Times


Drying Information
5°C 15°C 25°C 35°C
Touch Dry 15 hours 8 hours 3.5 hours 2 hours
Hard Dry 34 hours 18 hours 7 hours 4 hours
Walk-On Time 44 hours 18 hours 7 hours 4 hours
Before Flooding 3 days 2 days 24 hours 12 hours
Pot Life 2 hours 100 minutes 75 minutes 30 minutes



Overcoating Data
5°C 15°C 25°C 35°C
Overcoated By Min Max Min Max Min Max Min Max
Interbond 808 48 hours 14 days 30 hours 10 days 12 hours 7 days 8 hours 5 days



Surface Preparation


  • Paint only clean surfaces
  • Remove all grease, oil, soluble contaminants, and other foreign matter by "solvent cleaning" (SSPC-SP1)



Application Conditions


Major Refurbishment

  • Abrasive blast clean to Sa2 (ISO 8501:1:2007) or hydroblast to International Paint hydroblasting standard HB2M/H (If abrasive blasting, the area should be fresh water washed prior to commencement). Hydroblasting is only recommended for small ballast tank repairs, above water and topside areas
  • Interbond 808 may be applied to surfaces prepared to International Paint Slurry Blasting Standard SB2M/H. Slurry blasting is only recommended for above water areas and topside areas

Repair/OBM

  • Prepare areas of corrosion by mechanical cleaning to St3 (ISO 8501-1: 2007) or hydroblast to International Paint Standard HB2M/H. Abrade surrounding intact area and feather the edges
  • Interbond 808 may be applied to International Paint Slurry Blasting Standard SB2M/H. Slurry blasting is only recommended for above water and topside areas
  • If overcoating large areas of aged two component coatings, the surfaces should be high pressure fresh water washed prior to application. Consult your International Paint representative for specific recommendations regarding two component coatings suitable for overcoating with Interbond 808. Interbond 808 should not be used to maintain or overcoat one component ballast coatings
  • When applying Interbond 808 as a two-coat scheme, Interbond 808 Aluminium must always be applied as the first coat



Application


Ballast Tank Installation Guide

Cargo Oil Tanks Installation Guide

Mixing

Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified.

  • Agitate Base (Part A) with a power agitator
  • Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator

Thinner

  • International GTA220
  • Thinning is not normally required
  • Consult the local representative for advice during application in extreme conditions
  • Do not thin more than allowed by local environmental legislation

Airless Spray

  • Recommended Tip Range 0.45-0.66 mm (18-26 thou)
  • Total output fluid pressure at spray tip not less than 190 - 246 kg/cm² (2700 - 3500 p.s.i.)

Brush

  • Application by brush is recommended for small areas only
  • Multiple coats may be required to achieve specified film thickness

Roller

  • Not recommended

Cleaner

  • International GTA822/GTA220

Work Stoppages and Clean Up

  • Do not allow material to remain in hoses, gun or spray equipment
  • Thoroughly flush all equipment with International GTA822/GTA220
  • Once units of paint have been mixed, they should not be resealed, and it is advised that after prolonged stoppages work recommences with freshly mixed units
  • Clean all equipment immediately after use with International GTA822/GTA220
  • It is good working practice to periodically flush out spray equipment during the working day
  • Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays
  • Do not exceed pot life limitations
  • All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation

Welding

  • In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation



Limitations


  • This product will not cure adequately below 5°C. Substrate temperature should not exceed 40°C
  • Interbond 808 can be applied over a damp but drying surface - not a wet surface. It cannot be applied over pools of water or water droplets
  • A simple test for dampness is as follows: With a finger, mark a 'V' on the surface to be coated. If drops of water collect at the bottom of the 'V', then the surface is wet not damp and should not be coated
  • The surface may be dried however and coated if it does not become wet during application
  • Interbond 808 series is can continue its cure process once immersed in water. However, early immersion following application will tend to retard coating cure and may result in soft films. See 'Drying Times, before flooding'
  • The curing agent for Interbond 808 tends to go cloudy when stored at temperatures below 5°C. Warming the curing agent above 5°C will restore the clear nature of the produc.
  • No adverse effect on performance is observed if the curing agent is cloudy when used
  • Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions
  • Consult your local International Paint representative for specific recommendations
  • For optimum application properties bring the material to 25-30°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet
  • Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures 
  • Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments
  • As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating



Health and Safety


Please refer to the product data sheet and safety data sheets in the attachments section above.

Product Details
5213-863141

Data sheet

Manufacturer
International
For Use By
Professional Use
For Use On
Metal
Application Method
Brush, Spray
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Mixing Ratio
4 volume(s) Part A to 1 volume(s) Part B
Coverage
2.73 m²/litre at 300 microns dft
Recommended Thinner/Cleaner
Cleaner: International GTA822/GTA220
Max. Application Temperature
40°C
Min. Application Temperature
5°C
Solids by Volume
82%
Solids by Volume
82% ±2%
VOC
220 g/lt
Shelf Life (from date of manufacture)
12 months at 25°C
Touch Dry
5°C: 15 hours, 15°C: 8 hours, 25°C: 3.5 hours, 35°C: 2 hours
Size
20L
Recommended Dry Film Thickness
300 microns
Recommended Wet Film Thickness
366 microns
UN Number (Activator)
UN1263
UN Number (Base)
UN3470
Pot Life
5°C: 2 hours, 15°C: 100 minutes, 25°C: 75 minutes, 35°C: 30 minutes
Hard Dry
5°C: 34 hours, 15°C: 18 hours, 25°C: 7 hours, 35°C: 4 hours
Before Flooding
5°C: 3 days, 15°C: 2 days, 25°C: 24 hours, 35°C: 12 hours
Suitable For Use On
Metal
Application Method
Spray
Application Method
Brush
Product Usage Type
Tank Coating
Product Range
Interbond
Colour Family
Cream
Colour Family
Beige
Colour Family
Magnolia
Colour Family
Aluminium
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

International Interbond 808 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
International Thinner/Equipment Cleaner GTA220

International Thinner/Equipment Cleaner GTA220

International Thinner/Equipment Cleaner GTA220 is used for thinning compatible International products. It can also be used for the general cleaning of surafces and equipment after using the associated paint or coating.

Price £63.38 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
International Thinner/Equipment Cleaner GTA822

International Thinner/Equipment Cleaner GTA822

International Thinner/Equipment Cleaner GTA822 is used for thinning compatible International products. It can also be used for the general cleaning of surafces and equipment after using the associated paint or coating.

Price £63.38 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery