- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A 4,000+ colour intumescent paint system for interior and exterior timber surfaces.
These packs have been created to help users ensure they are purchasing sufficient product for their project. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Thermoguard Smoke & Flame Retardant (SFR) Dualcoat) to ensure protection is achieved in line with the manufacturers recommendations to the respective area in question.
- See Pack Contents below
- Other Kits are available for 60 minute protection, fire protection to doors, and for BS Class 1/0 & EN Class B
- IMPORTANT - The information from the manufacturer contained within the main description below must be read and referred to your relevant authority for approval BEFORE purchase and use of this product/system.
Please note that this product CANNOT be used without first receiving an application schedule from our Technical Department. Please download and complete the 'Thermoguard Wood Enquiry Form' and return by email to [email protected]
Product customisation
Don't forget to save your customization to be able to add to cartPlease note that this product CANNOT be used without first receiving an application schedule from our Technical Department. Please download and complete the 'Thermoguard Wood Enquiry Form' and return by email to [email protected]
If you have any questions regarding this process consult our technical department on 0113 2455450 (option 2).
Thermoguard Timbercoat 30 Minute System is a coloured intumescent paint system for interior and exterior timber surfaces. These packs have been created to help users ensure they are purchasing sufficient product for their project. Each pack contains the correct amount of basecoat (Timbercoat) and topcoat (Thermoguard Smoke & Flame Retardant (SFR) Dualcoat) to ensure protection is achieved in line with the manufacturers recommendations to the respective area in question.
4000+ colours available from RAL, BS & NCS
Quick Links - Click To Jump To Section:
- Other Kits
- Pack Contents
- System
- Drying Times
- Preparation & Application
- IMPORTANT
- Minimum Timber Board Thicknesses
- Beams and Joists
- Application to OSB/Sterling Board
- Spray Equipment Suggestions
Other Kits
Each component of the packs can still be purchased individually if required here: Thermoguard Timbercoat and here: Thermoguard Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
For 60 minute protection, see Thermoguard Timbercoat 60 Minute System
For fire protection to doors, see Door Upgrade Products
For BS Class 1/0 & EN Class B only see Thermoguard Timbercoat BS Class 1/0 & EN Class B System
Pack Contents
- 7m² Pack (Int/Ext. Spec.) = 1 x 5kg Timbercoat + 1 x 20m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 10m² Pack (Int/Ext. Spec.) = 1 x 5kg Timbercoat + 1 x 20m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 14m² Pack (Interior Spec.) = 2 x 5kg Timbercoat + 1 x 20m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 14m² Pack (Exterior Spec.) = 2 x 5kg Timbercoat + 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 20m² Pack (Interior Spec.) = 2 x 5kg Timbercoat + 1 x 20m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 20m² Pack (Exterior Spec.) = 2 x 5kg Timbercoat + 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 21m² Pack (Interior Spec.) = 3 x 5kg Timbercoat + 1 x 20m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 21m² Pack (Exterior Spec.) = 3 x 5kg Timbercoat + 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 28m² Pack (Interior Spec) = 1 x 20kg Timbercoat + 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 28m² Pack (Exterior Spec) = 1 x 20kg Timbercoat + 1 x 20m² & 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 30m² Pack (Interior Spec.) = 3 x 5kg Timbercoat + 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 30m² Pack (Exterior Spec.) = 3 x 5kg Timbercoat + 1 x 20m² & 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 40m² Pack (Interior Spec) = 1 x 20kg Timbercoat + 1 x 40m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
- 40m² Pack (Exterior Spec) = 1 x 20kg Timbercoat + 1 x 80m² Thermoguard Smoke & Flame Retardant (SFR) Dualcoat
System
10mm + thickness boards/3mm loss to char beams & joists (see below red text for full details)
- Apply 3 coats of Thermoguard Timbercoat @ 4m² per kg/per coat
15mm + thickness boards/7mm loss to char beams & joists (see below red text for full details)
- Apply 2 coats of Thermoguard Timbercoat @ 4m² per kg/per coat
Either application of Timbercoat should always be followed by;
- Internal Applications: 1 coat of Thermoguard Smoke & Flame Retardant (SFR) Dualcoat Satin or Matt
- External, Damp or High Wear Applications: 2 coats Thermoguard Smoke & Flame Retardant (SFR) Dualcoat Satin or Matt
2 coats of Thermoguard Smoke & Flame Retardant (SFR) Dualcoat may also be required for strong/dark colours - Thermoguard Timbercoat will be provided in a suitable undercoat shade to aid topcoat opacity unless instructed otherwise.
Please note: Timber must be clean and thoroughly dry prior to application (maximum 18% moisture content). Any gaps should be sealed with Thermoguard Intumescent Mastic. Fire should be prevented from accessing unprotected wood surfaces and for external applications it is recommended wood has been sealed on the reverse face to stop water ingress.
NOT suitable for the topside of floor surfaces that will be trafficked/walked on.
To achieve 30 minute protection minimum wood thicknesses apply of which approval must be sought before purchase.
Drying Times
Touch Dry: 1 hour / Overcoat: 4 hours in normal conditions.
Ensure fully hard dry before next coat, only apply to dry timber in good drying conditions.
Preparation & Application
Preparation:
All surfaces must be clean and dry. Remove all possible surface contaminates such as grease, smoke residues, silicates etc. Seal water-stain risks with stain blocking sealer suitable to overcoat with water-based acrylic paints. Abrade hard or smooth surfaces with wetted 120 grit wet-or dry abrasive or dust extracting abrader. Rinse off slurry while still damp. When dry, remove any loose or suspect material back to firm edge. Fill and repair any damage to the substrate using a good quality remedial filler.
Application:
Apply Thermoguard Timbercoat and Thermoguard Smoke & Flame Retardant (SFR) Dualcoat at rate stated on specification to protect surfaces & enable project Certification.
IMPORTANT
The below information from the manufacturer must be read and referred to your relevant authority for approval BEFORE purchase and use.
Please note that this product CANNOT be used without first receiving an application schedule from our Technical Department. Please download and complete the 'Thermoguard Wood Enquiry Form' and return by email to [email protected]
If you have any questions regarding this process consult our technical department on 0113 2455450 (option 2).
Half Hour and 1 Hour Resistance To Wood
In line with good common practice, we recommend that approval be sought for the use of our system, outlining our justification for the issuing of the Fire Certificate prior to the product’s use.
Authorities generally accept our Fire Test evidence (copies available upon request) as justification for the provision of One Hour Fire Resistance in cases such as this for up to 1 Hour Fire Resistance, depending upon the thickness of board in question.
We hold independent Fire Tests for Thermoguard Timbercoat to provide One Hour Fire Resistance to a mock-up of a ceiling comprising softwood timber boards on softwood joists, with the boards abutting one another and joined by metal tongues set into the abutting edges of the boards. Whilst the amount of residual undamaged timber was clearly adequate to have withstood office or accommodation design loads, the floor tested in the Fire Test did not have weight imparted to it, as we sought data to work from the test for sites with greatly differing make-ups.
The floor tested achieved One Hour Fire Resistance to BS 476 Part 22, with approximately 7mm of timber joist and board surfaces destroyed to charring during the test. Charring was greater up the open joints between floorboards, reaching 12mm, as one would expect being merely butt-jointed rather than tongue and groove jointed. Provided the calculated residual structure is adequate, we also issue Certification to BS 476 Part 21 to 30 or 60min Fire Resistance. The normal char factor of unprotected softwood for 60 minutes is approx 50mm, thus additional Fire Resistance provided by our Intumescent Paint was approximately 30 minutes.
A Fire Resistance test for 30mins was carried out at Warrington Fire Research Centre in January 2016 to 25mm softwood and 25mm MDF. Uncoated boards burnt through completely during the test.
- Application at 300 microns wet (12m² per 5kg) resulted in loss to char of 7mm on softwood and 5mm on MDF
- Application at 500 microns wet (8m² per 5kg) resulted in loss to char of 3mm on softwood and 2mm on MDF
Thermoguard Timbercoat was filmed by Channel 5 for documentary “Megastructures – Building from Disaster” which recorded in simultaneous parallel test to 18mm softwood that at 6mins uncoated board burnt through, while boards protected with Timbercoat @ 600 microns / 7m² per 5kg lost only 3mm to char at 45mins, with the protected board retaining insulation so that it was safe to put a hand on the reverse face while the burner continued on the front face.
Minimum Timber Board Thicknesses
- 30min protection - 10mm + thick boards minimum (select ‘10mm + thickness boards/3mm loss to char beams & joists’ above when ordering)
- 30min protection – 15mm+ thick boards (select ‘15mm + thickness boards/7mm loss to char beams & joists’ above when ordering)
Beams and Joists
- 30min protection - For wood which can afford to lose only 3mm to charring from exposed faces without collapsing, flame penetration or excessive heat penetration (select ‘10mm + thickness boards/3mm loss to char beams & joists’ above when ordering)
- 30min protection - For wood which can afford to lose 7mm to charring from exposed faces without collapsing, flame penetration or excessive heat penetration (select ‘15mm + thickness boards/7mm loss to char beams & joists’ above when ordering)
Note – For advice contact our technical team on 0113 2455450 (option 2) or send a message to [email protected].
Application to OSB/Sterling Board
Only surface spread of flame protection can be provided to OSB, for BS Class 1/0 & EN Class B s1 d0 ONLY see Thermoguard Timbercoat BS Class 1/0 & EN Class B System for details.
Spray Equipment Suggestions
- Pressure Pot & Gun conventional unit with small compressor
- Ensure all traces of solvent flushed out
- Thin 5 > 10% with water to spray viscosity
- Adjust fluid flow & air flow as normal for acrylic emulsion paint
OR
- Airless Graco 1500, 3500 or equivalent
- 3/8” line, 30 mesh filter on machine, not filter in gun
- 521,523, 621 or 623 tip
Ensure coverage and product quantity is applied as per specification.
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Data sheet
- Manufacturer
- Thermoguard
- Interior / Exterior Use
- Interior & Exterior
- Application Method
- Brush & Roller - Use woven fabric roller sleeves and synthetic bristle brushes
- Application Method
- Spray - Pressure Pot & Gun conventional unit with small compressor* (See important notes in Description tab
- VOC Levels
- Low Voc. Limit for this product (cat A/i) is 140 g/l. This product contains just 16 g/lv
- Single, Two or Three Pack
- Two-Pack
- Coverage
- Follow on-can guide to coverage, do not overspread as this compromises the system and results in non-compliance and inability to certify
- Touch Dry
- 1 hour
- Drying time
- In normal conditions touch dry 1 hour, over paintable with Thermoguard Smoke & Flame Retardant (SFR) Dualcoat after 4 hours
- Dry to Recoat
- 4 hours
- Suitable For Use On
- Wood
- Finish
- Matt
- Finish
- Eggshell
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Basecoat & Topcoat
- Product Range
- Timbercoat
- Fastest Delivery
- Next Working Day
- Application Conditions
- Min 8°C max 30°C. Max relative Humidity 75%. Surface should be at least 3°C above the dew point, free from condensation
- Cleaning
- Return as much unused material to its original container as possible. Wash brushes, rollers and guns with clean water immediately following use
- Health and Safety
- Please Refer To The Relevant Safety Data Sheet for full details of this product. Apply all products in accordance with BS 6150:2019- Code of practice for painting of buildings
- Health and Safety
- Do not store this product in cold temperatures below 5°C or above 30°C
- Colour Family
- Neutral
- Colour Family
- Dark
- Colour Family
- Lilac
- Colour Family
- Anthracite Grey
- Colour Family
- Salmon
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Fire Rating
- 30 Minutes
Questions
Question about the product
Sam Hughes on 2023-12-18 11:33:25 | Question:
Can this be used directly on OSB board? |
Answer from Rawlins’ Technical Team:
Thank you for your enquiry, for us to be able to fully assist, please fill out the form on the link below and return to [email protected] for a member of the Technical team to be able to assist further - Thermoguard_Wood_Survey_Form_NEW.pdf (rawlinspaints.com) | |
kevin stevens on 2023-05-02 08:08:45 | Question:
Can this be used on previously ordinary painted interior wooden surfaces |
Answer from Rawlins’ Technical Team:
Yes this can be applied to most previously painted substrates assuming they meet the minimum requirements of the system. Please send the information below to [email protected] and we can assist with a specification. GENERAL TIMBER SURFACES - Size of surface area to paint - Timber thickness - Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.) - Type of timber (i.e. pine, mdf, plywood, etc.) - Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.) - Internal or external - Use (i.e. floor, wall cladding, ceiling, etc.) - Clear or coloured coating required? - Bare or previously coated?
| |
Matt on 2023-02-24 14:31:12 | Question:
can i apply this start onto the timber joists as i want an open beam look? |
Answer from Rawlins’ Technical Team:
We will need the information listed below and pictures of the timber beams to assist with a specification, please can you send these to [email protected] GENERAL TIMBER SURFACES - Size of surface area to paint - Timber thickness - Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.) - Type of timber (i.e. pine, mdf, plywood, etc.) - Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.) - Internal or external - Use (i.e. floor, wall cladding, ceiling, etc.) - Clear or coloured coating required? - Bare or previously coated? | |
david morters on 2022-05-30 15:49:48 | Question:
please can you tell drying time between coats of thermoguard timbercoat |
Answer from Rawlins’ Technical Team:
The drying time between coats at 20°C is approximately 6 hours, this can vary dependant on temperature, humidity and airflow. | |
ruth johnson on 2021-08-06 12:40:52 | Question:
Hi, Can this be used on plasterboard and bare plaster? Thanks |
Answer from Rawlins’ Technical Team:
no, but assuming you require 30mins protection, the plasterboard is at least 9mm thick and building control approval is sought for this application, Thermoguard Wallcoat 30 & 60 Minute System for Plasterboard can be used. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Thermoguard Timbercoat 30 Minute System is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Thermoguard Timbercoat
An intumescent basecoat used as part 1 of a system to achieve 30 or 60 minute fire resistance for compartmentation. Can achieve 30 or 60 minutes Fire Resistance in certain instances subject to a specification from the Technical Department. For BS Class 1/0 and EN Class B only see Thermoguard Timbercoat Insulating Basecoat. Interior and...
Thermoguard Smoke & Flame Retardant Dualcoat
4,000+ matt and eggshell colours for use over Thermoguard Timbercoat or Thermoguard Timbercoat Insulating Basecoat. Topcoat and maintenance paint for timber surfaces protected with Thermoguard Timbercoat. Emits a safe fire-damping vapour in a fire to control flame spread and suppress smoke. As part of a complete system achieves 30 or 60...
General Painting Application Kit
Provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects, including uPVC surfaces, walls, ceilings, and more. Click to jump down to...
Thermoguard Timbercoat BS Class 1/0 & EN Class B System
4,000+ coloured fire retardant paint system for interior and exterior timber surfaces. Each pack contains the correct amount of basecoat (Thermoguard Timbercoat Insulating Basecoat) and topcoat (Smoke & Flame Retardant Dualcoat) to ensure protection is achieved in line with the manufacturers recommendations to the area in question....
Thermoguard Timbercoat Door Upgrade System
An intumescent paint system to upgrade solid doors to 30min Fire Resistance, with 4,000+ colour options. Available as a convenient pack containing the required basecoat and topcoat to protect 2 doors in a white or coloured Eggshell or Gloss finish Thermoguard UK will issue a Fire Certificate for Authority approved projects following...