- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta ViterLac DTM190 Primer/Finish is a one coat anti-corrosive alkyd primer/finish (gloss) for the ACE market. Fast drying single coat system for blast cleaned steelwork for in-shop application.
- Provides a colourful high gloss finish from one fast drying in-shop application
- Specially designed for the ACE market
- Available in a wide colour range
- For blast-cleaned steelwork
- Hard Dry in approximately 16hrs at 23°C
- Wide colour range of RAL and BS shades
- Designed for airless spray application
- Excellent build properties and hold-up on edges
- Resistant to splashes of diesel and hydraulic fluid (see Product Notes)
- Please Note: Colours tinted on a White base are only available in a 5L pack size. When using the colour picker, Price Bands 1 and 2 will show colours tinted on a White base, Price Bands 3 and 4 are for all other tintable colours
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartAxalta ViterLac DTM190 Primer/Finish is a one coat anti-corrosive alkyd primer/finish (gloss) for the ACE market. Fast drying single coat system for blast cleaned steelwork for in-shop application.
It is designed for airless spray application, and it has excellent build properties and hold-up on edges.
Axalta ViterLac DTM190 provides a colourful, high gloss system in one coat*.
*Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected].
Quick Links - Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- One-coat anti-corrosive alkyd primer/finish
- Specially designed for the ACE market
- For blast cleaned steelwork for in-shop application
- Available in a wide colour range
- Fast drying single coat system
- Excellent build properties and hold-up on edges
Product Specification
Technical Data | |
---|---|
Axalta ViterLac DTM190 Primer/Finish | |
Volume Solids | 55 ± 2% (varies with colour) |
VOC Content | 429 + 20 g/litre (varies considerably with colour) |
SG | 1.00 – 1.30 kg/lt (varies with colour) |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | 23-60°C |
Film Thickness Range And Coverage
Film Thickness Range & Coverage | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum | 50 µm | 91 µm | 11 m2/litre |
Maximum | 100 µm | 182 µm | 5.5 m2/litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times
Drying Times | ||||
---|---|---|---|---|
Applied to 70 microns DFT | 10℃ | 23℃ | 35℃ | |
Dust Free | 2.5 hr | 1 hr | 45 min | |
Hard Dry | 24 hr | 16 hr | 12 hr | |
Overcoating | Minimum | 24 hr | 10 hr | 10 hr |
Maximum | See Product Notes | |||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination
- Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
- Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns
Mixing
- Must be mixed thoroughly by using a mechanical agitator before use
- Agitate periodically to ensure paint remains homogeneous
Thinner
Thinner
Equipment Cleaner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing
- Do not apply when rain, mist, sleet or snow are imminent
- During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
- Paint temperature should ideally be at a minimum of 15ºC
Application Methods
- Airless Spray: Output fluid pressure at tip 2000-2500 psi, Tip Size 11-13 thou (0.28-0.33 mm)
- Conventional spray: typical atomising pressure 40-60 psi, will require thinning to 23-35 seconds at 25ºC through a BS B4 Flow Cup. Multiple coats will be required to achieve recommended dft
- Application by brush/roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
Product Notes
- Damaged areas may be touched up after the minimum times shown. Can be overcoated with itself indefinitely if clean and sound
- In common with most alkyd primers and primer/finishes, this product is not recommended for extended exterior exposure, exposure in aggressive or coastal locations, or for immersion. Epoxy primers are preferred for these conditions, please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice.
- When fully cured, ViterLac DTM190 resists splashes of diesel oil and hydraulic fluid. Splashes of petrol and brake fluid may cause some softening and loss of gloss. Splashes should be immediately removed to prevent long term film damage
- Some shades may contain lead based colourants and these are labelled (L)
- *Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems
Health & Safety
- Containers are provided with safety labels which should be observed
- Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Axalta Coating Systems
- For Use On
- Steel
- Application Method
- Airless Spray, Brush, Roller
- Sheen
- Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 5L, 20L
- Minimum Applied Thickness
- 50µm DFT 91µm WFT
- Maximum Applied Thickness
- 100µm DFT 182µm WFT
- Touch Dry (at 20°C)
- 60 mins
- Coverage
- 5.5m²/l @ 100µm DFT (182µm WFT) or 11.0 m²/l @ 50µm DFT (91µm WFT)
- Recommended Thinner/Cleaner
- Axalta Thinner 1006
- Solids by Volume
- 55 ± 2%
- Shelf Life (from date of manufacture)
- 12 months
- UN Number
- UN1263
- Dry to Recoat (at 23°C)
- 10 hours
- Specific Gravity
- 1.00 – 1.30 kg/lt (varies with colour)
- Hard Dry
- 16 Hours @ 23°C
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Suitable For Use On
- ACE (Agricultural, Construction & Earthmoving Equipment)
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Usages
- Force Dry Compatible
- Usages
- Primer/Finish
- Usages
- 1 Coat
- Usages
- Resistant to Diesel
- Usages
- Resistant to Hydraulic Fluid
- Usages
- Direct to Metal
- Usages
- High Build
- Usages
- In-Shop Application
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Product Usage Type
- Primer & Topcoat
- Product Range
- ViterLac
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Dark
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Product Type
- Alkyd
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 60 mins
- Drying Properties
- Force Dry Compatible
- Product Attributes
- 1 coat
- Product Attributes
- High Build
- Product Attributes
- Anti-Corrosive
- Product Attributes
- Primer/Finish
- Resistance to
- Diesel
- Resistance to
- Hydraulic Fluid
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterLac DTM190 Primer/Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT