- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta ViterLac Containergard HS is a single pack, modified alkyd primer/finish, specially developed for the transport container market and for Commercial Vehicle Chassis protection.
- One coat system* for Commercial Vehicle Chassis protection (* see Product Notes)
- High solids coating for dry cargo transport containers, ISO tank containers, anti-vandal accommodation units, waste containers and other industrial steel fabrications
- Wide colour range of over 350+ RAL and BS shades
- Fast drying - Good early water spotting resistance - Good exterior durability
- Indefinitely overcoatable for easy repair - Sheen finish disguises dents and welds
- Resistant to splashes of diesel, petrol and hydraulic fluid (see Product Notes)
- Tested to BS476 Part 7 (Surface Spread of Flame) - Class 1 and BS476 Part 6 (Fire Propagation) - Class 0
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartAxalta ViterLac Containergard HS is a single pack, modified alkyd primer/finish, specially developed for the transport container market and for Commercial Vehicle Chassis protection.
Axalta ViterLac Containergard HS is an excellent one coat system* with low VOCs to aid UK SED Compliance (*please see Product Notes).
Used for dry cargo transport containers, ISO tank containers, anti-vandal accommodation units, waste containers and other industrial steel fabrications.
Axalta ViterLac Containergard HS is fast drying and indefinitely overcoatable for easy repair. It is also resistant to splashes of diesel, petrol and hydraulic fluid (see Product Notes).
Approvals/Certification
Tested to:
- BS476 Part 7 (Surface Spread of Flame) - Class 1
- BS476 Part 6 (Fire Propagation) - Class 0
Quick Links - Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Single pack, modified alkyd primer/finish
- Specially developed for the transport container market and for Commercial Vehicle Chassis protection
- Low VOCs to aid UK SED Compliance
- Good early water spotting resistance and good exterior durability
- Fast drying and indefinitely overcoatable for easy repair
- Sheen finish helps disguise dents and welds
- Resistant to splashes of diesel, petrol and hydraulic fluid (see Product Notes)
- Tested to BS476 Part 7 (Surface Spread of Flame) - Class 1 and BS476 Part 6 (Fire Propagation) - Class 0
- Used for dry cargo transport containers, ISO tank containers, anti-vandal accommodation units, waste containers and other industrial steel fabrications
Product Specification
Technical Data | |
---|---|
Axalta ViterLac Containergard HS | |
Volume Solids | 61 ± 2% (varies with colour) |
VOC Content | 340 + 20 g/litre (varies with colour) |
SG | 1.37-1.41 kg/lt (varies with colour) |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | 23-60°C |
Film Thickness Range And Coverage
Film Thickness Range & Coverage | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum | 75 µm | 123 µm | 8.1 m2/litre |
Maximum | 125 µm | 205 µm | 4.9 m2/litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times
Drying Times | ||||
---|---|---|---|---|
Applied to 75 microns DFT | 10℃ | 23℃ | 35℃ | |
Dust Free | 1.5 hr | 30 min | 15 min | |
Hard Dry | 8 hr | 3 hr | 1.5 hr | |
Overcoating | Minimum - Wet-On-Wet | 20 min | 15 min | 10 min |
Maximum | Indefinite if surface is clean and sound | |||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination
- Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
- Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns
- Can also be applied to clean, dry, abraded steel
- Aluminium and Zinc coated surfaces: Surfaces should be degreased, abraded and etch primed prior to application of Axalta Containergard HS*
- Existing coatings: Containergard HS has been found to be tolerant to a wide range of existing coatings, including chlorinated rubber and vinyl systems which other topcoats may cause to soften or blister. A test area is recommended to ensure compatibility prior to full coating. Longer term performance will depend on the nature and integrity of the existing system and Axalta Coating Systems cannot assure results in these cases
*Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice.
Mixing
- Must be mixed thoroughly by using a mechanical agitator before use
- Agitate periodically to ensure paint remains homogeneous
Thinner
Thinner
Equipment Cleaner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing
- Do not apply when rain, mist, sleet or snow are imminent
- During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
- Paint temperature should ideally be at a minimum of 15ºC
Application Methods
- Airless Spray: Output fluid pressure at tip 2500 psi, Tip Size 15-17 thou (0.38- 0.43 mm)
- Conventional spray: requires thinning with 1006 Thinner which will increase the VOC content
- Brush should be used for touch-up of small areas
Product Notes
- Splash Resistance - when fully cured, resists splashes of diesel, petrol and hydraulic fluid. Splashes of brake fluid may cause some film softening and loss of gloss. Splashes should be immediately removed to prevent longer term film damage
- *Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems
Health & Safety
- Containers are provided with safety labels which should be observed
- Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Data sheet
- Manufacturer
- Axalta Coating Systems
- Interior / Exterior Use
- Exterior Use
- For Use On
- Steel
Aluminium
Zinc - Application Method
- Airless Spray
Spray
Brush - Sheen
- Sheen
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Product Certifications
- BS476 Part 7 (Surface Spread of Flame) - Class 1, BS476 Part 6 (Fire Propagation) - Class 0
- Pack Size
- 5L, 20L
- Minimum Applied Thickness
- 75µm DFT/123µm WFT
- Maximum Applied Thickness
- 125µm DFT/205µm WFT
- Touch Dry (at 20°C)
- 30 Mins
- Coverage
- 8.1m²/l at 75µm DFT/123µm WFT 4.9m²/l at 125µm DFT/205µm WFT
- Recommended Thinner/Cleaner
- Axalta Thinner 1006
- Solids by Volume
- 61 ± 2% (varies with colour)
- Shelf Life (from date of manufacture)
- 12 months
- UN Number
- UN1263
- Specific Gravity
- 1.37-1.41 kg/lt (varies with colour)
- Hard Dry
- 3hrs @ 23°C
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Suitable For Use On
- Compatible Existing Coatings
- Suitable For Use On
- Commercial Vehicle Chassis
- Suitable For Use On
- Transport Containers
- Finish
- Sheen
- Application Method
- Brush
- Application Method
- Spray
- Usages
- Exterior Durability
- Usages
- Overcoatable
- Usages
- Resistant to Diesel
- Usages
- Resistant to Hydraulic Fluid
- Usages
- Resistant to Petrol
- Usages
- BS476 Part 7 (Surface Spread of Flame) - Class 1
- Usages
- BS476 Part 6 (Fire Propagation) - Class 0
- Usages
- Direct to Metal
- Usages
- Low VOC
- Usages
- Atmospheric
- Usages
- 1 Coat
- Product Usage Type
- Primer & Topcoat
- Product Range
- ViterLac
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Dark
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Product Type
- Modified Alkyd
- Environment
- Atmospheric
- Environment
- Exterior Durability
- Touch Dry/Dust Free (@ 20-25°C)
- 30 mins
- Product Attributes
- 1 coat
- Product Attributes
- Overcoatable
- Product Attributes
- Low VOC
- Resistance to
- Hydraulic Fluid
- Resistance to
- Diesel
- Resistance to
- Petrol
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterLac Containergard HS is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT