- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta ViterLac TF95 Finish is a single pack, fast drying urethane-alkyd, high gloss finish, specially designed for the CV and ACE markets.
- Excellent flow, gloss and sag resistance with very high Distinction of Image
- Excellent chemical resistance coupled with superb weather resistance and gloss retention
- VOC rating below 420 gm/lt, complies with PG6/34b (06)
- High build for durability and protection
- Can be applied by airless, hot airless (with or without electrostatic), conventional and HVLP spray methods
- Hard Dry in approximately 2-3hrs at 23°C
- Wide colour range of RAL and BS shades
- Resistant to splashes of diesel, petrol and hydraulic fluid (see Product Notes)
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartAxalta ViterLac TF95 Finish is a single pack, fast drying urethane-alkyd, high gloss finish, specially designed for the CV and ACE markets.
For use on steel/general substrates, Axalta ViterLac TF95 Finish has excellent flow, gloss and sag resistance with very high Distinction of Image.
Axalta ViterLac TF95 Finish exhibits excellent chemical resistance coupled with superb weather resistance and gloss retention. It is a high build product which enhances durability and protection. It is also resistant to splashes of diesel, petrol and hydraulic fluid (see Product Notes).
Axalta ViterLac TF95 Finish is available in a wide range of RAL and BS colours, and can be applied by airless, hot airless (with or without electrostatic), conventional and HVLP spray methods.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Single pack, fast drying urethane-alkyd, high gloss finish
- For use on steel/general substrates
- Excellent flow, gloss and sag resistance with very high Distinction of Image
- Excellent chemical resistance coupled with superb weather resistance and gloss retention
- VOC rating of Below 420 gm/lt – complies with PG6/34b (06)
- High build for durability and protection
- Can be applied by airless, hot airless (with or without electrostatic), conventional and HVLP spray methods
- For application by brush or conventional spray
- Resistant to splashes of diesel, petrol and hydraulic fluid (see Product Notes)
- Available in a wide range of RAL and BS colours
Product Specification
Technical Data | |
---|---|
Axalta ViterLac TF95 Finish | |
Volume Solids | 50 ± 2% (may vary with colour) |
VOC Content | 368 + 20 g/litre (varies with colour) |
SG | 0.99 – 1.10 kg/lt (varies with colour) |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | 23-60°C |
Film Thickness Range And Coverage
Film Thickness Range & Coverage | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum | 25 µm | 50 µm | 20.0 m2/litre |
Maximum | 35 µm | 70 µm | 14.3 m2/litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times
Drying Times | ||||
---|---|---|---|---|
Applied to 25 microns DFT | 10℃ | 23℃ | 35℃ | |
Dust Free | 2 hrs | 40 min | 20 min | |
Hard Dry | 16 hr | 2-3 hr | 2 hr | |
Overcoating | Minimum | 16 hr | 16 hr | 16 hr |
Maximum | Indefinite if surface is clean and sound | |||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- This product is a finish coat and should be applied over an appropriate primer and/or intermediate coat
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination
Mixing
- Must be mixed thoroughly by using a mechanical agitator before use
- Agitate periodically to ensure paint remains homogeneous
Thinner
Thinner
Equipment Cleaner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing
- Do not apply when rain, mist, sleet or snow are imminent
- During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
- Paint temperature should ideally be at a minimum of 15ºC
Application Methods
- Airless Spray: Output fluid pressure at tip 2000 psi min., Tip Size 11-13 thou (0.28-0.33 mm)
- Hot airless: ready for use as supplied. Suitable for hot spray at 60-80°C, with or without electrostatic. Apply a ‘mist’ coat followed by a full coat. Some colours may thicken on heating and require some thinning. Hot spray gives a higher build and can lead to slower through-hardening
- For multi-colour applications allow to dry at least overnight before masking - a longer time may be necessary for hot spray applications*
- Conventional spray and HVLP: will require thinning by approx. 10% (9:1 by volume) with 1736 Thinner to 22-32 seconds BSB4 @ 25°C. Note: this may render the thinned product non-compliant with PG6/34b (06). Please check the VOC content of the particular colour used and degree of thinning to ensure compliance*
*Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice.
Product Notes
- Overcoating: if primers or undercoats are de-nibbed or flatted prior to overcoating, an extended period should be allowed before application of ViterLac TF95 to allow the surface to harden again. Failure to allow this extra time can result in lifting and crazing
- Splash Resistance: when fully cured, ViterLac TF95 resists splashes of diesel, petrol and hydraulic fluid. Splashes of brake fluid may cause some film softening and loss of gloss. Splashes should be immediately removed to prevent longer term film damage
- For best opacity, particularly with tinted colours such as bright yellows, oranges and reds, this product should be applied over a primer or intermediate coat tinted to the recommended undercoat shade – Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice
- Some shades may contain lead based colourants, and these are labelled (L)
Health & Safety
- Containers are provided with safety labels which should be observed
- Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Axalta Coating Systems
- For Use On
- Steel
- Application Method
- Airless Spray, Spray
- Sheen
- Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Minimum Applied Thickness
- 25µm DFT, 50µm WFT
- Maximum Applied Thickness
- 35µm DFT, 70µm WFT
- Coverage
- 20.0m²/l (25µm DFT, 50µm WFT), 14.3m²/l (35µm DFT, 70µm WFT)
- Recommended Thinner/Cleaner
- 1736 Thinner
- Solids by Volume
- 50 ± 2% (may vary with colour)
- Shelf Life (from date of manufacture)
- 12 Months
- UN Number
- UN1263
- Dry to Recoat (at 23°C)
- 16hrs
- Specific Gravity
- 0.99 – 1.10 kg/lt (varies with colour)
- Hard Dry
- 2-3hrs @ 23°C
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Finish
- Gloss
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Product Range
- ViterLac
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- Neutral
- Colour Family
- Dark
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterLac TF95 Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT