- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta ViterShield SPF Epoxy Primer/Finish is a two-pack epoxy, mid-sheen primer/finish for blast cleaned steelwork.
- Low temperature curing (down to 0ºC) and low tendency to bloom
- Use as an anticorrosive primer/undercoat or primer/finish for general structural steelwork
- High build airless spray capability
- Good resistance to undercutting from damaged areas
- Overcoatable with most epoxy, acrylic or polyurethane coatings
- Use as a base coat for most thin film intumescent coatings
- Wide colour range of over 350+ RAL and BS shades
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartAxalta ViterShield SPF Epoxy Primer/Finish is a two pack epoxy, mid-sheen primer/finish for blast cleaned steelwork.
Axalta ViterShield SPF Epoxy Primer/Finish cures at low temperatures (down to 0ºC) and has a low tendency to bloom.
Used as an anticorrosive primer/undercoat or primer/finish for general structural steelwork, Axalta ViterShield SPF Epoxy Primer/Finish has high build airless spray capability and good resistance to undercutting from damaged areas.
Axalta ViterShield SPF Epoxy Primer/Finish is available in a wide range of RAL and BS colours.
It is overcoatable with most epoxy, acrylic or polyurethane coatings and it can be used as a base coat for most thin film intumescent coatings.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Two pack epoxy, mid-sheen primer/finish
- Low temperature curing (down to 0ºC) and low tendency to bloom
- Use as an anticorrosive primer/undercoat or primer/finish for general structural steelwork
- High build airless spray capability
- Good resistance to undercutting from damaged areas
- Overcoatable with most epoxy, acrylic or polyurethane coatings
- Use as a base coat for most thin film intumescent coatings
- Hard Dry in approximately 2hrs at 23°C
- Available in a wide range of RAL and BS colours
Product Specification
Technical Data | |
---|---|
Axalta ViterShield SPF Epoxy Primer/Finish | |
Volume Solids | 60 ± 2% (may vary with colour) |
VOC Content | 421 + 20 g/litre (varies considerably with colour) |
SG | 1.54 – 1.58 kg/lt mixed, varies with colour |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | 23-60°C |
Pot Life | 8 hours at 23°C |
Film Thickness Range And Coverage
Film Thickness Range & Coverage | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum | 75 µm | 125 µm | 8.0 m2/litre |
Maximum | 200 µm | 333 µm | 3.0 m2/litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times
Drying Times | ||||
---|---|---|---|---|
Applied to 100 microns DFT | 10℃ | 23℃ | 35℃ | |
Dust Free | 1 hr | 30 min | 15 min | |
Hard Dry | 4 hr | 2 hr | 1 hr | |
Overcoating | Minimum* | 8 hr | 4 hr | 2 hr |
Maximum | Indefinite if surface is clean and sound | |||
*See Product Notes. Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
Mixing
Mixing Ratio:
- Base 3403 or 3321 (L) - 3 parts by volume
- Hardener 4050 077 - 1 part by volume
Notes:
- Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator
- Agitate periodically during use to ensure product remains homogeneous
Thinner
Thinner
Equipment Cleaner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing
- Do not apply when rain, mist, sleet or snow are imminent
- During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
- Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process
- Paint temperature should ideally be at a minimum of 15ºC
Application Methods
- Airless Spray: Output fluid pressure at tip 2500-3000 psi, Tip Size: 15-21 thou (0.38-0.53mm)
- For airless spray application at low temperatures, up to 5% by volume of 1031 Thinner may be added to ensure achievement of a closed film
- Application by brush/roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
- Refer to Axalta Coating Systems ‘Epoxy Application and Curing Notes’
Product Notes
- Minimum overcoating with itself: allow a minimum 4 hours at 23ºC, when SPF has been applied to 75-100 dft
- Minimum overcoating with 2p polyurethanes and non-iso (i.e. ViterThane PLV or PLS, or ViterSeal EA80): allow a minimum 6 hours at 23ºC, when SPF has been applied to 75-100 dft
- Allow longer drying and overcoating times at higher dft’s and lower temperatures
- A minimum of 100 microns dft will be required to achieve a consistent solid appearance with white, pastel and other low opacity shades
- Do not apply or cure below 0°C, temperatures above 10°C are recommended
- Some shades may contain lead colourants, these are labelled SPF (L)
- Like all epoxy coatings, this product will chalk on prolonged exterior exposure, the degree of which is subject to atmospheric conditions
Health & Safety
- Containers are provided with safety labels which should be observed
- Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Axalta Coating Systems
- For Use On
- Steel
- Application Method
- Airless Spray
- Sheen
- Mid Sheen
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
- Minimum Applied Thickness
- 75µm DFT/125µm WFT
- Maximum Applied Thickness
- 200µm DFT/333µm WFT
- Touch Dry (at 20°C)
- 30 Mins
- Coverage
- 8.0m² (75µm DFT/125µm WFT), 3.0m² (200µm DFT/333µm WFT)
- Recommended Thinner/Cleaner
- Axalta 1031 Thinner/950 Thinner
- Solids by Volume
- 60 ± 2% (may vary with colour)
- Shelf Life (from date of manufacture)
- 12 Months
- UN Number (Activator)
- UN1263
- UN Number (Base)
- UN1263
- Dry to Recoat (at 23°C)
- Allow a minimum 4 hours, when SPF has been applied to 75-100 DFT
- Pot Life
- 8 hrs @ 23°C
- Specific Gravity
- 1.54 – 1.58 kg/lt mixed, varies with colour
- Hard Dry
- 2hrs @ 23°C
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Finish
- Mid Sheen
- Application Method
- Spray
- Usages
- High Build
- Usages
- Low Temperature
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Usages
- Primer/Finish
- Usages
- Overcoatable
- Usages
- Direct to Metal
- Product Usage Type
- Primer & Topcoat
- Product Range
- ViterShield
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Dark
- Categorised As
- Metal Paints > Low Temperature Direct-to-Metal Paints
- Seasonal
- Cold Weather
- Product Type
- Epoxy
- Environment
- Atmospheric
- Environment
- Low Temperature
- Touch Dry/Dust Free (@ 20-25°C)
- 30 mins
- Product Attributes
- High Build
- Product Attributes
- Anti-Corrosive
- Product Attributes
- Primer/Finish
- Product Attributes
- Overcoatable
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterShield SPF Epoxy Primer/Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta ViterThane PLS Recoatable PU Finish
Axalta ViterThane PLS Recoatable PU Finish, A two pack recoatable polyurethane semi-gloss finish for use on protective systems for steelwork. Excellent colour retention and indefinitely overcoatable. Excellent chemical resistance and low temperature cure. An aliphatic polyurethane providing a tough and durable semi-gloss finish with...
Tikkurila Thinner 1031
Tikkurila Thinner 1031 is a thinner for epoxy paints, silicone paints, polyvinylbutyral paints, 2-component zinc rich paints and epoxy shop primers.
Axalta ViterThane PLV Finish
Axalta ViterThane PLV Finish is a two pack recoatable polyurethane gloss finish for use on protective systems for steelwork. Provides a tough and durable gloss finish together with excellent gloss and colour retention Excellent chemical resistance and low temperature curing down to -5ºC Withstands dry heat up to 150ºC (discolouration may...
Axalta 950 Thinner
Axalta 950 Thinner, for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...