Axalta ViterFloor 300 SF Epoxy Floor Coating is a two pack epoxy, solvent free, high build coating for concrete floors.

This product is suitable for new and old concrete floors subject to heavy mechanical wear and/or chemical attack, in areas such as the food processing, brewing, pharmaceutical and heavy engineering industries.

Axalta ViterFloor 300 SF Epoxy Floor Coating has a high gloss, easily cleaned finish which is resistant to water, oils, weak solutions of non-oxidising acids, alkali and salt solutions. It is also resistant to temporary splashes of oxidising acids and bleaches.

Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Product Specification
• Film Thickness Range And Coverage
• Drying Times
• Surface Preparation
• Mixing
• Thinner
• Application Conditions
• Application Methods
• Product Notes
• Health & Safety

Features & Benefits

• Two pack epoxy, solvent free high build coating
• For new and old concrete floors
• high gloss, easily cleaned finish
• Resistant to water, oils, weak solutions of non-oxidising acids, alkali and salt solutions, and temporary splashes of oxidising acids and bleaches
• VOC free
• Accepts light traffic after 48hrs @23°C (300µm dft)
• Wide colour range of over 350+ RAL and BS shades

Product Specification

Film Thickness Range And Coverage

Drying Times

*Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.

Surface Preparation

• All surfaces must be clean, dry, and free from grease, oil, laitance, dust and other contamination
• Apply over ViterFloor 400 Primer/Sealer – consult relevant Product Data Sheet for details

Mixing

Mixing Ratio:

• Base 2995 - 4 parts by volume (5 parts by wt.)
• Hardener 2995 101 - 1 part by volume (1 part by wt.)

Mixing Instructions:

• Components must be mixed thoroughly by using a mechanical mixer (with side scraper) before use
• Add hardener in the correct proportions and mix thoroughly for a minimum of 2 minutes
• Mix the material just before use, and consider the area to be coated and pot life of the material when deciding how many units are required
• Note: do not scrape or pour out remaining residues of mixed material from the bottom and sides of the container onto the floor, as this material may be incompletely mixed and cause ‘soft spots’ in the applied floor coating
• It is recommended that all material is stored at a temperature of approximately 20ºC for at least 24 hours prior to use, to aid mixing and application

Thinner

Thinner

• Do Not Thin

Equipment Cleaner

• 1031 Thinner

Application Conditions

• Only apply in conditions of good ventilation which must be maintained during drying and curing
• Do not apply when rain, mist, sleet or snow are imminent
• During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
• Paint temperature should ideally be at a minimum of 15ºC

Application Methods

• This product is recommended for application by serrated or steel trowel, felt or mohair roller, with brush being used only where required to cut-in around edges or for very small areas
• Pour out the mixed ViterFloor 300 onto the primed floor and spread with a suitable trowel
• Level with a mohair or felt roller, wearing spiked shoes to walk across the wet coating
• Refer to Axalta Coating Systems ‘Epoxy Application and Curing Notes’

Product Notes

Priming:

• Apply over ViterFloor 400 Primer/Sealer – consult relevant Product Data Sheet for details

DFT:

• Below 300 µm dft performance will be reduced
• This solvent free material can be applied in excess of 500 µm, but where additional thickness is required, a second coat is recommended

Anti-Slip:

• Dependent on the degree of anti-slip required, aggregate can be broadcast onto the wet coating surface and allowed to dry
• Surplus non-adhering particles should then be brushed off and further coats of ViterFloor 300 applied (if required) to encapsulate the particles
• Please note: The higher the degree of anti-slip, the lower the ease of cleaning will be

Application Temperatures:

• Do not apply or cure below 5°C, temperatures above 10°C recommended

Health & Safety

• Containers are provided with safety labels which should be observed
• Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]