- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG 1K DTM 70 Colour is a single pack direct to metal compliant coating, giving good corrosion and early moisture resistance, ideal for application as a single coat primer finish for use on skips, containers, agricultural and construction vehicles and machinery.
- Professional use only
- Low Odour
- Recoat at any stage, ready for use
- Quick drying – touch dry after 2 hours at 20°C
- Spray application
- Coverage: 6m²/L
- Improved performance at higher film weights
- Please note: Light shades may require dust coat
- Available in 3,500 colours from RAL, NCS, and British Standard
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application
- Health & Safety
Features & Benefits 
- Recoat at any stage, ready for use
- Suitable for most clean and degreased metal surfaces
- Quick drying – touch dry after 2 hours at 20°C
- Coverage: 6m²/L
- Wet film thickness: 150 microns
- Dry film thickness: 100 microns
- Recommended Thinner: HMG 2621
- PG6/23 11 Compliant
- Manufactured under the auspices of an ISO 9001 management system
- Available in 3,500 colours from RAL, NCS, and British Standard
Product Specification
| Technical Data | |
|---|---|
| HMG 1K DTM 70 Colour | |
| Volume Solids: | 55% |
| VOC Content: | 0.410Kg/L |
| Viscosity: | 300 mPas |
| Density: | 1.187 g/cm³ at 20℃ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed |
| Shelf Life: | 12 months from delivery date in original sealed containers |
| Flash Point: | 24°C |
Drying Times
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 2 hours |
| Hard Dry: | 24 hours |
| Dry To Recoat: | At any stage |
| Full Dry: | 7 days |
Surface Preparation
- Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application
- Read and follow the safety data sheet, product data sheet (see section above) and label instructions
- Stir all paints thoroughly before use
- Thoroughly clean and degrease using suitable HMG Prep Clean. Abrade with P80 – P180 if necessary
- Reduce emissions and maintain quality by replacing tin lid after use
Application
- Apply HMG 1K DTM evenly via Airless/Air-assisted, Pressure Pot, Compliant Spray. 1-2 full coats
- Read and follow safety data sheet, technical data sheet (see section above), and label instructions
- Stir paint thoroughly before use
- Always use the same batch number on the same job
- Check colour and sheen
- Filter the product immediately before use. Reduce emissions and maintain quality by replacing tin lid after use
- High pressure wash to remove all loose debris and other contamination
- Thoroughly clean and degrease using suitable HMG Prep Clean - Apply by cloth and quickly remove using clean lint free cloth
- Repeat until surface is clean and free from all deposits (grease, oil, silicone). Replace cloths regularly to ensure that contamination is not re-applied to the surface
Painting existing coatings (powder coated)
- Check all existing coatings are well adhered with all loose and failed material removed back to firm with all edges well feathered
Substrates
- Suitable for application direct to most suitably prepared metals
- Not suitable for coating over bitumen orchlorinated rubber coatings
- Suitability over existing coating should be trialled in small area prior to full application
Application Climate
- Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰ above the dew point
- Adequate dry air ventilation should be supplied during drying
Application Information
- Thinning should only take place after material is thoroughly mixed
- Application and use should always conform with the codes of practice described in BS 6150 and BS 5493
| Technical Data | |||
|---|---|---|---|
| Airless/Air-Assisted | Pressure Pot | Compliant Spray Gun | |
| Thinner Options: | - | - | Thinner 2621 |
| Spray Gun Setup: | 13 - 15 thou | 2.0 | 1.6 - 2.0 |
| Number Of Coats (Guide Only): | 1 full coat | 1 full coat | 2 full coats |
| Flash Off: | 15 minutes between coats | 15 minutes between coats | 15 minutes between coats |
For further assistance, please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use
- Suitable respiratory equipment should be worn when spraying
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a non-combustible container with a tight fitting lid
Product Details
5461-887262
Data sheet
- Manufacturer
- HMG Paints Ltd
- For Use By
- Professional Use
- For Use On
- Metal
Skips
Metal Containers
Agricultural Machinery
Construction Machinery - Application Method
- Spray
- Sheen
- 70% Sheen
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Product Certifications
- PG6/23 11 Compliant
- Pack Size
- 5L
15L - Touch Dry (at 20°C)
- 2 hours
- Dry to Recoat (at 20°C)
- Any stage
- Fully Cured (at 20°C)
- 7 Days
- Coverage
- 6 square metres per litre @ 100 microns dft
- Recommended Thinner/Cleaner
- HMG Thinner 2621
- Solids by Volume
- 55%
- VOC
- 0.362Kg/L
- Shelf Life (from date of manufacture)
- 12 months
- UN Number
- UN1263
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Suitable For Use On
- Steel
- Suitable For Use On
- Agricultural Machinery
- Suitable For Use On
- Construction Machinery
- Suitable For Use On
- Skips
- Suitable For Use On
- Metal Containers
- Suitable For Use On
- Powder Coated Surfaces
- Finish
- Semi-Gloss
- Application Method
- Spray
- Manufacturer
- HMG Paints LTD
- Usages
- Low Odour
- Usages
- Corrosion Resistance
- Usages
- Atmospheric
- Usages
- 1 Coat
- Usages
- Water Resistance
- Usages
- Overcoatable
- Usages
- Direct to Metal
- Product Usage Type
- Primer
- Product Range
- 1K DTM
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 2 hours
- Product Attributes
- 1 coat
- Product Attributes
- Overcoatable
- Product Attributes
- Low Odour
- Resistance to
- Corrosion
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG 1K DTM 70 Colour is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
You might also like
HMG Prep Clean 2803
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. HMG Prep Clean 2803 is a slow evaporating, low odour and mild preparatory cleaning solvent for the degreasing of substrates. Used in many...
In stock
HMG Thinner 2621
HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems.
Price
£13.45
(incl. VAT)
In Stock and Available for Delivery
HMG 1K DTM 30 Colour
HMG 1K DTM 30 Colour is a single pack direct to metal compliant coating, giving good corrosion and early moisture resistance, ideal for application direct to metal as a single coat primer finish for use on skips, containers, agricultural and construction vehicles and machinery. Low Odour Improved performance at higher film weights...
Price
£53.14
(incl. VAT)
In Stock and Available for Delivery
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£25.93
(incl. VAT)
In Stock and Available for Delivery