Follow us on:

Tremco CS175 Epoxy Primer for Porous Substrates | Water based epoxy primer
Tremco CS175 Epoxy Primer for Porous Substrates | Water based epoxy primer

Tremco CS175 Epoxy Primer for Porous Substrates

350571 350572
TRE5593

Tremco CS175 Epoxy Primer for Porous Substrates is a two part water based epoxy primer. CS175 provides a breathable sealer for calcium sulphate screeds. Additionally, it is suitable for priming new and existing cementitious screeds, concrete, brick and blockwork.

  • May be used as a low viscosity primer for epoxy paint coatings on prepared power floated concrete
  • Excellent coverage - 10m² per kg depending on the substrate and method of application
  • Low viscosity
  • Consolidates weak surfaces
  • Please note: Colours shown are approximate and are for illustrative purposes only
  • Please note this product is subject to a minimum order quantity
Colour
Size
£79.93(incl. VAT)
£66.61(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

The minimum purchase order quantity for the product is 2.

No queries yet, leave the first!
Description

Tremco CS175 Epoxy Primer for Porous Substrates is a two part water based epoxy primer. CS175 provides a breathable sealer for calcium sulphate screeds. Additionally, it is suitable for priming new and existing cementitious screeds, concrete, brick and blockwork.

May be used as a low viscosity primer for epoxy paint coatings on prepared power floated concrete.

Floor coverings may be laid directly using suitable flooring adhesives. Before applying smoothing compounds onto anhydrite screed, Tremco CS100 Epoxy Primer must be used.

 

Benefits:

  • Excellent coverage - 10m² per kg depending on the substrate and method of application
  • Low viscosity
  • Consolidates weak surfaces
  • For detailed product information please see the Product Data Sheet

 

 Preparation:

  • Surfaces should be clean, firm and free from dust, dirt or other material liable to impair adhesion

 

Application Conditions:

  • New concrete should be a minimum of 28 days old
  • Surface temperatures should be +3°C above the dew point
  • Temperatures should be above +5°C at time of application and for 24 hours thereafter
  • Do not apply over wet substrates or externally if rain is expected prior to curing
  • Where used internally, especially in high humidity conditions, forced ventilation will be required to assist curing
  • At lower temperatures and in internal situations, allow a minimum of 24 hours, before overcoating
  • If contaminated before installing floor finishes, it will be necessary to sand the surface of the primer and reapply one or two coats as required

 

Mixing:

  • Add contents of Part A (small bottle) to Part B (large container) and mix thoroughly for a minimum of 2 minutes

 

Application:

Concrete and Sand Cement Screeds:

  • Apply an even continuous coat, which is free of pinholes to the substrate using a fluff free roller
  • Take care to prevent the formation of puddles. On smooth impervious substrates, application by squeegee is the most effective way to quickly obtain a uniform film
  • Leave the coating to dry to a translucent film (usually 3 to 6 hours depending on substrate, temperature and ventilation). If in doubt, leave overnight
  • Once dried, the primed surface is ready for overlaying and must be kept free of contaminants
  • If more than 24 hours have elapsed since the application, then a repeat application of the primer may be required

Calcium Sulphate Screeds:

  • Prepare all surfaces by mechanical techniques as recommended by the screed manufacturer to provide a clean, sound, smooth contaminant free surface with a fine texture
  • Remove all traces of dust and debris
  • Apply 1 or 2 coats of mixed CS175 Epoxy Primer for Porous Substrates (as required) and allow each coat to dry (usually 3 to 6 hours depending on substrate, temperature and ventilation)
  • Once the calcium sulphate screed is dry (Refer to specific manufacturer’s instructions) secure the floor covering with the approved Tremco adhesive

 

Technical Data:

Property Result
Composition A two part water based epoxy primer
Pot Life 20°C: Approximately 45 minutes
Curing Time Overnight
Coverage  10m² per kg depending on the substrate and method of application
Storage Store in shaded dry conditions between +10°C and +35°C
Shelf Life 12 months when stored as recommended in original unopened containers

 

Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.

Product Details
5593-888124

Data sheet

Manufacturer
Tremco
Water / Solvent Based
Water
For Use On
Concrete, Brick, Blockwork, Cementitious Screeds,
Application Method
Roller, Squeegee
Colour
Clear
Single, Two or Three Pack
Two-Pack
Pack Size
7.5kg
Dry to Recoat (at 20°C)
Usually 3 to 6 hours depending on substrate, temperature and ventilation. If in doubt, leave overnight
Coverage
10m² per kg depending on the substrate and method of application
Recommended Thinner/Cleaner
Water
Shelf Life (from date of manufacture)
12 Months
UN Number (Activator)
N/A
UN Number (Base)
UN3082
Base Type
Water-Based
Suitable For Use On
Concrete
Suitable For Use On
Brick
Suitable For Use On
Blockwork
Suitable For Use On
Cementitious Screeds
Application Method
Squeegee
Application Method
Roller
Usages
Breathable
Usages
Low Viscosity
Product Usage Type
Primer
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Tremco CS175 Epoxy Primer for Porous Substrates is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like