- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Tremco SF115 Contact Adhesive is a one-part, modified elastomer contact adhesive for use with rubber and PVC. SF115 has been specially developed for contact bonding (two-way stick) of a wide range of floor coverings including: rubber tiles and sheet, vinyl and cork.
- Also suitable for horizontal and vertical surfaces for bonding rubber/PVC nosing and covings
- Extra strong bond
- Extended working life
- Fast drying but long ‘open time’
- The dry bond does not support combustion
- Coverage of approx. 2.5 - 3m² of bonded area per litre
- Please note: Colours shown are approximate and are for illustrative purposes only
- Please note this product is subject to a minimum order quantity
Tremco SF115 Contact Adhesive is a one-part, modified elastomer contact adhesive for use with rubber and PVC.
SF115 has been specially developed for contact bonding (two-way stick) of a wide range of floor coverings including:
- Rubber tiles and sheet
- Vinyl and cork
To horizontal and vertical surfaces:
- Rubber nosing and covings
- PVC nosings and covings
Where superior water resistance is required use SF165 Water Resistant Contact Adhesive.
Benefits:
- Also suitable for horizontal and vertical surfaces for bonding rubber/PVC nosing and covings
- Extra strong bond
- Extended working life
- Fast drying but long ‘open time’
- The dry bond does not support combustion
- Coverage of approx. 2.5 - 3m² of bonded area per litre
- For detailed product information please see the Product Data Sheet
Preparation
Site conditions MUST comply with British Standards CP 102, BS 8203, BS 5325 and supplementary specifications.
- The surfaces must be sound, clean, dry and free from oil, grease, paint, dust and other contaminants liable to impair adhesion
- Concrete and sand/cement screeds must be fully cured and free from laitance
- Direct to earth subfloors must incorporate an efficient damp proof membrane
- Underfloor heating must have been fully commissioned as per manufacturer's instructions and must be switched off 48 hours before and during installation
- The heating should be switched on 48 hours after completion but then only gradually as per the commissioning schedule. Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Priming
- Ensure substrate is suitable for the adhesive before application
Application
- Stir the adhesive thoroughly before use and apply an even continuous coating, using a ‘V’ notched trowel size 1 mm x 4 mm
- With some rubber floor coverings, it is recommended that the adhesive is applied to the floor with the ‘V’ notched trowel and to the back of the rubber with a flat spreader
- Refer to the Flooring Manufacturer’s instructions
- For vertical surfaces, a bristle brush application may be convenient
- Allow the solvents to evaporate until the adhesive on both surfaces is ‘touch dry’. This may take approximately 5 to 45 minutes, according to prevailing conditions
- Place the materials accurately into position and press firmly to exclude air and ensure overall contact.
- On horizontal surfaces, roll in both directions using a 68kg flooring roller.
LIMITATION
- This product is not suitable for use with certain types of PUR vinyl
- Please check with the floor covering manufacturer
Technical Data:
Property | Result |
---|---|
Composition | A modified chloroprene elastomer dissolved in a blend of flammable solvents |
Specific Gravity | 0.82 - 0.86 |
Flash Point | Below -18°C |
Application Temperature Range | +4°C to +30°C |
Service Temperature | -20°C to +85°C |
Coverage | 2.5 - 3m² of bonded area per litre |
Dry Tack Time | Up to 40 minutes after becoming touch dry |
Drying Time | 5 to 45 minutes |
Final Bond Strength | 36 to 48 hours |
Storage | Store between +5°C and +27°C |
Shelf Life | 12 months from manufacturing date, when stored as recommended in original unopened containers |
Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Data sheet
- Manufacturer
- Tremco
- Interior / Exterior Use
- Interior Use
- Water / Solvent Based
- Solvent
- For Use On
- Rubber, PVC
- Application Method
- Notched Trowel
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Coverage
- 2.5 - 3m² of bonded area per litre
- Recommended Thinner/Cleaner
- Tremco AW421 Heavy Duty Cleaner
- Max. Application Temperature
- 30°C
- Min. Application Temperature
- 4°C
- Shelf Life (from date of manufacture)
- 12 Months
- UN Number
- UN1133
- Drying time
- 5 - 45 minutes according to prevailing conditions
- Specific Gravity
- 0.82 - 0.86
- Base Type
- Solvent-Based
- Suitable For Use On
- PVC
- Suitable For Use On
- Rubber
- Application Method
- Trowel
- Usages
- Quick Drying
- Usages
- Long Open Time
- Product Usage Type
- Adhesive
- Colour Family
- Beige
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tremco SF115 Contact Adhesive is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Tremco SF165 Water Resistant Contact Adhesive
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Tremco SF165 Water Resistant Contact Adhesive is a cross-linking contact adhesive used for the permanent bonding of smooth backed rubber floor...
Tremco AW421 Industrial Cleaner
Tremco AW421 Industrial Cleaner is a powerful solvent-based cleaning solution for dissolving and removing mastics, adhesives and sealants. AW421 will remove many common adhesives and sealants, particularly in the uncured state. The product may also be used for cleaning and to degrease other surfaces that are not sensitive to solvents, such as...