- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Tremco SF200 Carpet Tile Tackifier is a single component, white waterborne liquid adhesive, which dries to a clear, permanently tacky film.
- SF200 has a multitude of uses, but has been specifically developed for use on:
- Release bonding of Hexphalte/ Bitumen backed carpet tiles
- Some grades of PVC backed carpet tiles and thermoplastic hot melt backed tiles
- Underfelts
- Solvent free
- Non-flammable
- Meets existing low VOC requirements
- Can be used on impervious surfaces
- Suitable for metal access flooring
- Coverage of up to 135m² per 15 litre unit
- Please note: Colours shown are approximate and are for illustrative purposes only
- Please note this product is subject to a minimum order quantity
Tremco SF200 Carpet Tile Tackifier is a single component, white waterborne liquid adhesive, which dries to a clear, permanently tacky film. This product has been developed for the installation of Hexphalte/Bitumen backed carpet tiles, some grades of PVC backed carpet tiles, thermoplastic hot melt backed tiles, and underfelts. The adhesive can be used to bond the floor coverings to concrete, sand/cement and is particularly suited for bonding carpet tiles to non-porous surfaces e.g. raised access flooring.
Benefits:
- Solvent free
- Non-flammable
- Meets existing low VOC requirements
- Can be used on impervious surfaces
- Suitable for metal access flooring
- Coverage of up to 135m² per 15 litre unit
- For detailed product information please see the Product Data Sheet
Preparation
Site conditions MUST comply with British Standards CP 102, BS 8203, BS 5325 and supplementary specifications.
- The surfaces must be sound, clean, dry and free from oil, grease, paint, dust and other contaminants liable to impair adhesion
- Concrete and sand/cement screeds must be fully cured and free from laitance
- Direct to earth subfloors must incorporate an efficient damp proof membrane
- Underfloor heating must have been fully commissioned as per manufacturer's instructions and must be switched off 48 hours before and during installation
- The heating should be switched on 48 hours after completion but then only gradually as per the commissioning schedule. Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information
Priming
- Very porous or dusty surfaces should be primed with a thin coat of SF200 Carpet Tile Tackifier adhesive
Application
- The adhesive must be thoroughly stirred before use
- Spread a uniform coating of the adhesive using either a roller or brush and allow to dry until it takes on a clear appearance, when the adhesive become tacky
- Carpet tiles should be placed into the tacky film of adhesive, press firmly from the centre outwards to exclude air and to ensure overall contact
- During the curing period, the adhesive must be kept free of dust and be undisturbed until the floor covering is placed in position
- Remove and replace existing tiles
- The back of the carpet tiles which must be lifted and replaced should be coated with SF200 Carpet Tile Tackifier and allowed to dry before placing into position
- The subfloor must be free of all contaminants and loose particles
Technical Data:
Property | Result |
---|---|
Composition | A white acrylic polymer emulsion |
Open Time/Workability (at +20°C) |
30 - 60 minutes on non-absorbent substrates 15 - 25 minutes on cementitious screeds |
Specific Gravity | 0.98 - 1.02 |
Flash Point | None |
Application Temperature Range | +4°C to +30°C |
Service Temperature | -20°C to +60°C |
Coverage | Up to 135m² per 15 litre unit |
Dry Tack Time | Up to 4 hours |
Storage | Store between +5°C and +30°C DO NOT ALLOW TO FREEZE |
Shelf Life | 12 months from manufacturing date, when stored as recommended in original unopened container |
Please contact Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Data sheet
- Manufacturer
- Tremco
- For Use On
- Bitumen, PVC, Felt
- Application Method
- Roller, Brush
- Colour
- Clear
- Single, Two or Three Pack
- Single
- Pack Size
- 15L
- Coverage
- Up to 135m² per 15 litre unit
- Recommended Thinner/Cleaner
- Water
- Max. Application Temperature
- 30°C
- Min. Application Temperature
- 4°C
- Shelf Life (from date of manufacture)
- 12 Months
- Touch Dry
- Up to 4 hours
- UN Number
- N/A
- Open time
- At 20°C: 30 - 60 minutes on non-absorbent substrates 15 - 25 minutes on cementitious screeds
- Specific Gravity
- 0.98 - 1.02
- Suitable For Use On
- PVC
- Suitable For Use On
- Mineral Felt
- Suitable For Use On
- Bitumen
- Application Method
- Brush
- Application Method
- Roller
- Usages
- Impervious Surfaces
- Product Usage Type
- Adhesive
- Colour Family
- Clear
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tremco SF200 Carpet Tile Tackifier is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT