- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Decorative, thin film intumescent base coat that delivers a Class 0 rating over solid timber and particle boards when used in conjunction with Bollom Flameguard Ultra Topcoats.
- Achieves Class 0 fire protection rating to BS476: Parts 6 and 7
- Hard wearing protective/decorative finish
- Water-based
- For all types of timber in communal areas
Description
Bollom Broflame Ultra Basecoat
Bollom Broflame Ultra Basecoat is ideal for all types of interior timber in communal areas.
Recommended Uses
- Solid timber
- Timber-faced boards
- Particle boards
- Communal interior timber
- Public buildings
- Schools
- Hospitals
Together with one of the Bollom Flameguard Ultra Topcoats this system provides a means of achieving your desired colour scheme and finish, whilst providing Class 0 on the painted surface. The paints are designed to inhibit surface spread of flame and heat release, providing vital escape time in the event of a fire.
NOTE:It is important to speak to our Technical Department and refer to the product data sheet prior to using this product to ensure the correct specification has been chosen for your surface.
Preparation
Ensure the surface to be painted is sound, clean, dry and free from grease or any substance liable to give adhesion problems. Treat any knots. Scrape off any old or flaking paint until you have a firm well adhered surface; if in doubt remove all existing coatings. For existing gloss and eggshell finishes wet abrade and rinse with clean water to remove any residues.
Application
- Stir well before use.
- Applied by brush or airless spray, can be applied by roller but must be subsequently laid off with a brush to achieve a smooth finish.
- Bollom Broflame Ultra Basecoat must not be thinned.
- Coverage rates must be adhered to in order to achieve the Class 0 upgrade.
- Apply two coats @ 5m² per litre/per coat taking care to avoid runs or sags allow at least 4 hours between coats. After the second coat leave 24 hours before applying Flameguard Ultra Top coats.
How do I get Fire Certification?
To obtain the completed certificates for a project customers should email [email protected] with the following details:
- Proof of purchase
- The contractors/applicators name and contact details (tel. no, email, address)
- Batch number(s) of product(s) used
- Site address
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Product Details
563-183721
Data sheet
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior Use
- Single, Two or Three Pack
- Single
- Application
- Brush, Roller, Spray
- Coverage
- 5m² per litre
- Touch Dry
- 4 Hours
- Base Type
- Water-Based
- Suitable For Use On
- Wood
- Finish
- Matt
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Base Coat
- Product Range
- Broflame
- Fastest Delivery
- Next Working Day
- Colour Family
- White
Questions
Question about the product
Andrew Thomas
on
2023-11-10 14:30:16
| Question:
Under the new holiday home regulations we have to create a 30 min fire protected escape route in a 2 storey cottage. We intend using Broflame ultra on the timber doors and frames. How many coats of base and top coat to achieve 30 mins. Incidentally the walls are either solid granite or plasterboard stud. |
Answer from Rawlins’ Technical Team:
This product will only achieve a Class 0 fire protection rating to BS476: Parts 6 and 7. We have e-mailed seperately to request more information in order to assist with a 30min timed rating requirement. | |
|
pete duffy
on
2018-11-13 16:24:22
| Question:
We are currently carrying out a shop fit using 18mm MDF fixed to 75 x 50 CLS timber studding The finish IS lining paper, then 2 coats of washable white matt emulsion Building Inspector said he would accept am intumescent paint What do you recommend Doors and door frames are FD30 |
Answer from Rawlins’ Technical Team:
Could you confirm the level of fire protection you are being asked to achieve on the MDF please? This is extremely important to ensure we provide the correct advice/product. Also, do you know how many square metres there will be to paint? | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Bollom Broflame Ultra Basecoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Bollom Flameguard Ultra Vinyl Matt
Top coat in 4,400+ matt colours for Bollom Broflame Ultra Basecoat on bare and previously painted wood and Bollom Brosteel Ultra 60. Provides Class 0 on non-combustible surfaces. Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour. Buy A Paint Colour Sample...
Price
£87.23
(incl. VAT)
In Stock and Available for Delivery
Temporarily Out-of-Stock
Bollom Flameguard Ultra Primer / Undercoat
This product is temporarily unavailable; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. A primer/undercoat for application prior to the use of Bollom Flameguard Ultra Topcoats on bare and previously painted non-combustible...
Price
£96.00
(incl. VAT)
Temporarily Out-of-Stock
Bollom Flameguard Ultra Acrylic Eggshell
Top coat in 4,400+ eggshell colours for Bollom Broflame Ultra Basecoat on bare and previously painted wood, and Bollom Brosteel Ultra 60 for steel. Provides Class 0 on non-combustible surfaces. Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour. Buy A Paint...
Price
£108.74
(incl. VAT)
In Stock and Available for Delivery
Bollom Flameguard Ultra Gloss
Top coat in 4,400+ gloss for Bollom Broflame Ultra Basecoat on bare and previously painted wood, also Bollom Brosteel Ultra 60 for steel. Provides Class 0 on non-combustible surfaces Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour. Buy A Paint Colour Sample...
Price
£43.52
(incl. VAT)
In Stock and Available for Delivery
General Painting Application Kit
Provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects, including uPVC surfaces, walls, ceilings, and more. Click to jump down to...
Price
£12.08
(incl. VAT)
In Stock and Available for Delivery