- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG C71 Speedline Aerosol is a high quality, single pack, synthetic alkyd enamel suitable for brushing or spraying. Offers fast surface drying, good through drying (even in thick films), and a hard, tough finish, with minimal yellowing even at high temperature - ideal for machinery, appliance and agricultural projects.
- For use on ferrous and suitably prepared non-ferrous metals
- Can be used as part of a finishing system for more demanding exposure scenarios
- For application to fencing, gates and other ironmongery, previously painted or primed timber, agricultural, construction and earth-moving equipment
- Ideal for small touch up areas
- For Professional or Industrial use only
- For the non-aerosol version of this product please see HMG C71 Speedline
- Available in 3,500 colours from RAL, NCS, and British Standard
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartClick To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness
- Drying Times
- Surface Preparation
- Application
- Resistance
- Health & Safety
Features & Benefits
- 400ml/16oz Aerosol
- Available in packs of 1 or packs of 2-10, 40, 50, 100 and 500 with qty price breaks
- High Temperature resistant - up to 170°C
- Minimal yellowing at high temperature even after prolonged exposure
- Good chemical resistance - see Resistance sheet (in 'Data Sheets' tab above) for more information
- Quick-drying paint for agricultural, appliance and machinery use - touch dry in 2 hours at 20℃
- For application to fencing, gates and other ironmongery, previously painted or primed timber, agricultural, construction and earth moving equipment
- Good resistance to chemicals, oils and fats
- Ideal for small touch up areas
- Brush or spray application
- 12 months shelf life from delivery date in original sealed containers
- Available in 3,500 colours from RAL, NCS, and British Standard
Product Specification
Technical Data | |
---|---|
Volume Solids: | 54.5% |
VOC Content: | 0.45Kg/L |
Viscosity: | 320 mPas |
Density: | 1.062 g/cm³ |
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
Shelf Life: | 12 months from delivery date in original sealed containers. |
Flash Point: | -42°C |
Film Thickness
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Aerosol: | 50 µm | 100 µm |
Coverage: 10m² per litre @ 50 microns dft
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 90 mins |
Hard Dry: | 4 hours |
Full Dry: | 12 hours |
Surface Preparation
Bare Substrates:
- New Galvanised Steel to be degreased using suitable:
- Application of HMG Mordant Wash prior to application of HMG Etch Primer and suitable HMG Primer
- Aged Galvanised to be degreased using:
- HMG Prep Clean 2802 Degreaser
- HMG Prep Clean 2803 Degreaser
- or HMG Prep Clean 2804 Degreaser
- and lightly abraded prior to application of suitable HMG Primer
- Aluminium to be degreased using:
- HMG Prep Clean 2802 Degreaser
- HMG Prep Clean 2803 Degreaser
- or HMG Prep Clean 2804 Degreaser
- abrade with P180 – P320, prior to application of suitable HMG Etch Primer and suitable HMG Primer
- Mild Steel remove millscale and thoroughly degrease using:
- HMG Prep Clean 2802 Degreaser
- HMG Prep Clean 2803 Degreaser
- or HMG Prep Clean 2804 Degreaser
- abrade with P80 – P180 if necessary, before applying suitable HMG Primer
- Shot Blasted Steel remove all traces of blast grit/sand before applying suitable HMG Primer
Previously painted/General Maintenance:
- High pressure wash to remove all loose debris and poorly adhered existing coatings to remove salts and other contaminants
- Degrease using suitable HMG Prep Clean 2800 to remove grease and oils not removed with pressure washing alone
- Remove all loose and failed coatings back to firm, wire brush to remove rust and corrosion to clean metallic appearance
- All edges to be firm and well feathered
- Abrade to promote good adhesion
- Wipe over with degreaser to remove loose debris from abrasion
- Substrate to be clean, free of grease, oils, dust and completely dry prior to application
Application
- Read and follow Safety Data Sheet, Product Information Sheet, and label instructions in the 'Data Sheets' section above
- Shake can for a minimum of 2 minutes prior to use ensuring that the contents are fully mixed
- A trial sample should be done prior to application to guarantee correct colour & sheen
- Hold the can 10 - 20cm from surface to be sprayed, moving the can steadily in a straight line, overlapping slightly on each pass
Substrates:
- C71 Speedline is suitable for use on all properly cleaned and prepared bare ferrous and non-ferrous metals and most previously coated metals
- Previous coatings should be fully cured and prepared, test patch is recommended to check compatibility
- Previously painted timber should be dry with all coatings sound and fully adhered
- Failed previous coatings should be removed back to firm well feathered edge
- Suitable primer is recommended for use over aluminium and new galvanised metals
- Rusted steel to be suitably prepared and anti-corrosive primer applied prior to C71
- Not for application over chlorinated rubber or bitumen coatings
Application Climate:
- Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point
- Adequate dry air ventilation should be supplied during drying
Surface Preparation:
- Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application
- Thoroughly degrease using suitable HMG degreaser and where applicable, abrade to remove rust and promote good adhesion
- For best results and optimum corrosion protection mild steel should be blast cleaned to Sa2.5
If in doubt, please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Resistance
Health & Safety
- Refer to the Safety Data Sheet in the 'Data Sheets' section above, as well as tin label prior to use
- Suitable respiratory equipment should be worn when spraying
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid
Data sheet
- Manufacturer
- HMG Paints Limited
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Bare Ferrous metals
Bare Non-Ferrous metals
Fencing
Gates
Iron
Timber
Agricultural Machinery
Construction Machinery
Vehicles - Application Method
- Aerosol
- Sheen
- Satin
Matt
Gloss
Semi-Gloss
Textured - Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 400ml/16oz Aerosol
- Base Type
- Synthetic Alkyd
- Touch Dry (at 20°C)
- 90 minutes
- Dry to Handle (at 20°C)
- 4 Hours
- Dry to Handle (at 20°C)
- 4 Hours
- Dry to Recoat (at 20°C)
- After 12 Hours
- Fully Cured (at 20°C)
- 12 Hours
- Coverage
- 10m²/L
- Recommended Thinner/Cleaner
- HMG Thinner 2611/2612
- Solids by Volume
- 25.4 %
- Heat Resistance (up-to)
- 170°C
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- UN Number
- UN1950
- Resistance to chemicals
- Calcium Chloride
Alcohol
Sea Water
Mineral Oil
Animal Fats
Vegetable Fats
Alum
Copper Sulphate
Sodium Chloride
Codium Sulphate
Sodium Acetate
Sodium Phosphate - Flashpoint
- -42°C
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal Fencing
- Suitable For Use On
- Metal Gates
- Suitable For Use On
- Construction Machinery
- Suitable For Use On
- Timber
- Suitable For Use On
- Suitably Prepared Metal
- Suitable For Use On
- Painted Ferrous Metal
- Suitable For Use On
- Ferrous Metals
- Suitable For Use On
- Non-Ferrous Metals
- Suitable For Use On
- Vehicles
- Suitable For Use On
- Iron
- Suitable For Use On
- Machinery
- Suitable For Use On
- Agricultural Machinery
- Finish
- Matt
- Finish
- Satin
- Finish
- Gloss
- Finish
- Semi-Gloss
- Finish
- Textured
- Application Method
- Aerosol
- Manufacturer
- HMG Paints LTD
- Usages
- High Temperature Resistance
- Usages
- Metal Protectors
- Product Usage Type
- Topcoat
- Product Range
- Speedline
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Purple
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Beige
- Colour Family
- Grey
- Product Type
- Epoxy
- Product Attributes
- Non-Yellowing
- Product Attributes
- Tough / Durable
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG C71 Speedline Aerosol is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG C71 Speedline
HMG C71 Speedline is a high quality, single pack, synthetic alkyd enamel suitable for brushing or spraying. Offers fast surface drying, good through drying (even in thick films), and a hard, tough finish, with minimal yellowing even at high temperature - ideal for machinery, appliance and agricultural projects. For use on ferrous and...
HMG Thinner 2611
HMG Thinner 2611 is a medium thinner. For use with compatible HMG systems.
HMG Thinner 2612
HMG Thinner 2612 is a slow thinner. For use with compatible HMG systems.
HMG Hardener 9029 ZIP
HMG Hardener 9029 ZIP is an isocyanate hardener. Designed for use in recommended HMG Alkyd and Polyurethane Alkyd systems. Upgrades the performance characterstics of the system, including durability and time to touch dry may decrease by 10 - 20% dependant on paint system, film thickness and curing conditions.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...