Glixtone Fungi-Shield Concentrated Sterilising Solution, approved by the National Residential Landlords Association (NRLA), is a specially prepared, water-based surface biocide which destroys mould or fungi. Used to sterilise prepared surfaces prior to the application of Glixtone Fungi-Shield Paint.

Ideal for any internal areas that are susceptible to mould or organic growth including: walls, ceilings, woodwork, bathrooms, shower rooms, kitchens, bedrooms and living areas.

Glixtone Fungi-Shield Concentrated Sterilising Solution eliminates spores, is colourless and easy to apply.

Glixtone Fungi-Shield Concentrated Sterilising Solution must be diluted with water prior to use - 1 x 240ml bottle makes 5 litres.

Glixtone is affiliated with the National Residential Landlords Association (NRLA) as a Recognised Supplier.

Landlords face an on-going battle with properties and the infestation of mould which is both unsightly and a health hazard to their Tenants. Re-decoration is expensive, time consuming and disruptive. If Health Inspectors are notified this can also be a real problem to Landlords.

Glixtone Fungi-Shield will not stop condensation or damp, however, when applied it is impossible for mould spores to survive on its surface as the active biocide is distributed evenly over the entire paint film and will continue to kill spores on contact. Glixtone Fungi-Shield offers a long lasting solution to what can be a never ending battle. 

Quick Links - Click To Jump To Section:

   
• Features & Benefits
• How Do I Use Glixtone Sterilising Solution?
• Limitations

Features & Benefits

   
• Also available pre-diluted and ready to use, please see Glixtone Fungi-Shield Diluted Sterilising Solution (minimum order quantity and an extended lead time applies)
• GS36 must be diluted with water prior to use - 1 x 240ml bottle makes 5 litres
• Kills mould spores prior to painting
• Enables decoration of treated surfaces with minimal risk of re-infection
• Environmentally friendly water-borne formulation
• No fire or solvent vapour hazards during application or use
• Good coverage - 6-8m² per litre (when mixed) when used on a smooth surface of average porosity
• Ideal for use by Landlords who can face an on-going battle with properties and the infestation of mould which is both unsightly and a health hazard to their Tenants
• Approved by the National Residential Landlords Association (NRLA)
• For detailed information please see the Product Data Sheet, also please see the Application Guide and Information Sheet for Glixtone Fungi-Shield

How Do I Use Glixtone Sterilising Solution?

• First, wash the affected areas with Glixtone Concentrate Sterilising Solution diluted 5:1 with water
• You may not need to use 5 litres. If not, mark the 240ml container into 5 equal parts, each of which can be diluted with 1 Litre of water
• Allow to dry
• After the above treatment, you may notice a ‘Stained’ area. These are Mould Spores which may grow back
• On these ‘Stained’ areas apply Glixtone Concentrate Sterilising Solution UNDILUTED using a sponge and rubber or disposable gloves
• Wipe over the stained area with the Sterilising Solution but DO NOT WASH OFF
• Leave to FULLY dry
• This will kill the spores and seal against oxygen ingress
• If there are other stains such as water marks, rust stains etc, then a ‘Stain Block’ should be used prior to application of Glixtone Fungi–Shield
• Fungi-Shield can now be painted on the whole area
• After 5 days this painted area will be fully washable and give a high quality emulsion finish, ideal for any internal areas that are susceptible to mould or organic growth including: walls, ceilings, woodwork, bathrooms, shower rooms, kitchens, bedrooms and living areas

Limitations

• DO NOT apply outside when there is a risk of rain or frost
• When using inside, ensure good ventilation
• Please Note: If Glixtone Fungi-Shield coatings are over-painted with anything other than Glixtone Fungi-Shield products, the fungicidal properties will be lost
• Please refer to the Safety Data Sheet before use