- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A water-based coating which has been specially formulated to bring tarmac and concrete surfaces back to life, for a fraction of the cost of re-surfacing. Suitable for interior and exterior use.
- Tough and long lasting slip resistant finish which renews and protects tarmac.
- Safe water-based product, eco friendly.
- Used to colour cycle ways and pedestrian refuges, renews and protects driveways, provides clear demarcation areas for indoor floors, corridors and offices.
Britannia Tarmac Reviver is a water-based coating which has been specially formulated to bring tarmac and concrete surfaces back to life, for a fraction of the cost of re-surfacing.
It provides a tough and long lasting slip resistant finish for interior and exterior use.
Used to colour cycle ways and pedestrian refuges, renews and protects driveways, provides clear demarcation areas for indoor floors, corridors and offices. It is also suitable for use on porous substrates.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Spreading Rate
- Drying Times
- Preparation
- Application
- Cleaning
- Shelf Life & Storage
- Precautions
Features & Benefits
- Safe water-based product
- Eco-friendly
- Tough and long lasting
- Slip resistant finish
- Equally suitable for tarmac or concrete surfaces
- Single-pack product
- Interior and exterior use
- Application by brush, roller
- Not suitable for heavy traffic areas
- Please Note: Old polished granite macadams and power floated concrete areas as well as chemically or mechanically hardened floors may not be suitable for coating
Spreading Rate
These will vary depending on substrate, the site conditions and longevity required.
Typically spreading rates will vary depending on the end use.
- 6-8m² per litre for brush or roller application
- Dependent on substrate, texture and porosity of the surface
- Apply 2 coats
Drying Times
- Drying is approximately 2-4 hours dependent on ambient temperature
- Avoid painting when rain is expected or under poor drying conditions – below 5°C
- Curing of the coating can be extended at lower temperatures, dependent on coating thickness, substrate and texture
Preparation
- All surfaces should be dry (not damp)
- Free from loose or flaking material, dirt grease and vegetative growth
- Vacuum or pressure blasting with air or water may remove any debris
- Brushing (manual or machine) may be suitable
- If in doubt always test a small area prior to use
- Not to be applied if there is salt contamination or frost
Application
- Stir well before use as stainers used can separate with time, best to mix thoroughly when using different batches
- Surfaces that are cold – below 5°C – are not suitable for coating
- Hot surfaces – above 30°C – should be cooled with water spray before application otherwise paint will dry before film formation is completed
- Please follow the coverage rates shown in Spreading Rate Section
- Apply an even coat either by brush or roller
- A new macadam surface should be left to oxidise for at least four weeks (longer in winter than in summer) before painting
- Not suitable for use on open graded macadam or other materials incorporating “cut back” bitumen
- New concrete should be allowed to mature for several months before coating
- Priming is not normally required, however the first coat on concrete or porous surfaces, should first be thinned up to 10% with water and allow to dry
- Apply during April to October (exterior)
Cleaning
- Clean all equipment with water immediately after use
Shelf Life & Storage
- Up to 12 months if stored correctly in an unopened container
- Store above 5°C
Precautions
- Keep out of reach of children
- In case of contact with eyes wash immediately with plenty of water
- Remove splashes from skin with soap and water or a recognised hand cleaner
- Protect from freezing
- Do not apply paint if there is a risk of heavy rain or frost
- Do not use near fishponds
Data sheet
- Interior / Exterior Use
- Interior & Exterior
- Water / Solvent Based
- Water
- For Use On
- Tarmac
Concrete - Application Method
- Brush
Roller - Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Coverage
- 6-8 square metres per litre. Apply 2 coats.
- Recommended Thinner/Cleaner
- Water
- Min. Application Temperature
- 5°C
- Shelf Life (from date of manufacture)
- 12 months
- Touch Dry
- Approximately 2-4 hours
- UN Number
- N/A
- Base Type
- Water-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Tarmac
- Finish
- Matt
- Application Method
- Brush
- Application Method
- Roller
- Components
- 1K
- Product Usage Type
- Topcoat
- Colour Family
- Green
- Colour Family
- Red
- Colour Family
- Black
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Britannia Tarmac Reviver is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT