Could this be applied to a sanded plywood substrate for high foot traffic ramp? What are the flexibility characteristics of this paint once cured? thanks, sid

No, for plywood this product wouldn't be suitable. Assuming the plywood is lightly abraded, clean, dry, sound and prepared as detailed in the technical datasheet, you could consider Coo-Var High Performance Primer followed by 2 coats of Coo-Var ProGrip Heavy Duty Two Pack Anti-Slip Floor Paint , to leave a hardwearing, aggregated, off-gloss finish for heavy trafficked areas.

Is it UV stable - won't yellow if the sun is on it?

This product does state that is is non yellowing which indicates good colour retention, however we don't have any testing results for UV protection so couldn't confirm if this would be suitable.

Hi, is the paint ready mixed or do you have to add harder and thiners?

Blackfriar Professional High Traffic Floor Paint is a 2 pack epoxy coating so a 5lt is supplied in 2 tins - 1 tin of base and a smaller tin of activator. You should add the activator to base container and mix thoroughly for at least 5 minutes until product is smooth and even. Allow to rest 5 minutes before using

I am considering using "Blackfriars High Traffic Paint" on a car parking bay. The 6mm asphalt surface course is old so existing oils on the surface course should not be a problem. Question: Does your product contain MMA which seems to be a prefered additive? Alternatively do you have any suggestions?

Blackfriar Professional High Traffic Floor Paint is not suitable for asphalt, instead we would suggest 703 MMA Flexible Anti-Slip Coating assuming the surface is not currently painted.

how does this product deal with (skydrol) aircraft hydraulic fluid, which are phosphate ether based? and what floor preparation is required? chemical /mechanical? do you offer product solutions to floors that require sealing first i.e concrete saturated in fluid

There has been no testing carried out on Blackfriar Professional High Traffic Floor Paint for Skydrol exposure but our 310 Chemical Resistant Coating and 304 HD Epoxy Floor Coating have both been tested for full immersion. Under fully immersed conditions (i.e. constant contact/exposure) 304 would require re-coating after 1-2 years and 310 would require coating after 5-10 years. Concrete should be a minimum of 21 days old and/or the residual moisture content below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes etc. Blow holes and defective concrete can be made good using 201 Epoxy Repair Mortar . Suitable mechanical treatment such as vacuum grit blasting of suitable diamond floor grinding is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating. A coat of 401 Epoxy Floor Primer is recommended on absorbent concrete surfaces. Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.

Blackfriar Professional High Traffic Floor Paint

Reference BF2170351A1

Brand Blackfriar Professional

Search ID BLA688

Exceptionally hard-wearing, high performance, easy-to-clean 2-pack solvent based floor coating in 4,400+ colours ideal for indoor and outdoor use. Provides outstanding resistance to a wide range of chemicals, non-yellowing, excellent colour fastness.

Resists grease, oil and solutions of acid and alkali
Minimises disruption due to rapid drying time – vehicular traffic can use after just 3 days
Can be applied over concrete, metal, brickwork and stone
Indoor and outdoor high traffic areas
Solvent-based

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart

Colour Group

Size

Finish

£116.96(incl. VAT)

£97.47(ex. VAT)

Quantity

Please choose your colour

In Stock and Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

5 questions about the product

Description

Blackfriar Professional High Traffic Floor Paint is an exceptionally hard-wearing, high performance, easy-to-clean 2-pack floor coating, ideal for indoor and outdoor use. It can be tinted to any RAL, BS or NCS colour (except metallic and fluorescent shades) and is available in Tile Red and Mid Grey colours as standard, it produces a non-yellowing, semi-gloss, colour-fast finish.

Blackfriar Professional High Traffic Floor Paint provides an exceptionally hard wearing finish for surfaces such as brickwork, concrete, metal and stone. It protects floors with an easy-to-clean two pack solvent based polyurethane coating giving excellent resistance to solvents, grease, oil and solutions of acid and alkali, making it ideal for commercial and industrial use.

Features & Benefits

A high performance solvent based polyurethane acrylic
Resists grease, oil and solutions of acid and alkali
Ideal for Indoor and outdoor high traffic areas
Minimises disruption due to rapid drying time - vehicular traffic can use after just 3 days
Brush or roller application
Can be applied over concrete, metal, brickwork and stone
Can be tinted to BS, RAL and NCS colours

Preparation

Ensure the surface to be painted is sound, clean, dry and free from grease or any substance liable to give adhesion problems. Scrape off any old or flaking paint until you have a firm surface. Special attention should be given to areas under cars to ensure all oil, grease, dirt and road salt is removed. Prepared surfaces with residual oil contamination should be primed with Blackfriar Professional Oil Tolerant Primer. New concrete must be left for at least 6 months before applying Blackfriar Professional High Traffic Floor Paint. Power-floated floors should either be blast tracked or treated with Blackfriar Professional Acid Etch followed by thorough rinsing. New or exposed bare concrete should be primed with Blackfriar Professional Epoxy Floor Primer.

Mixing

Base and activator are supplied in correct proportions. Add all activator to base container and mix thoroughly for at least 5 minutes until product is smooth and even. Allow to rest 5 minutes before using. DO NOT MIX PART UNITS. Badly activated or incorrectly mixed materials will affect performance and may cause early failure or discolouration. The mixed material has a usable pot life of 6 hours at 20°C.

Application

Apply with a good quality medium pile roller - smaller areas may be brushed.

Limitations

Not suitable for spray. Blackfriar Professional High Traffic Floor Paint is not suitable for use over PVC, thermoplastic tiles, quarry tiles or granolithic concrete. Do not apply it on concrete surfaces treated with alkali containing liquids, areas subjected to rising damp or areas treated with PVA bonding solutions. If applying over single pack conventional floor paint the existing coating must be aged and fully cured. Surfaces may be slippery when wet. To ensure slip resistance the floor must be kept dry when in use. The use of protective mats will help preserve the surface under tyres.

Product Details

Reference 688-970682

Data sheet

Manufacturer: Blackfriar Professional
For Use By: Professional Use
Interior / Exterior Use: Interior & Exterior
Sheen: Semi-Gloss
Colour: Fully Tintable
Single, Two or Three Pack: Two-Pack
Pack Size: 5L
Dry to Recoat (at 20°C): 8-48hrs
Coverage: 12m² per litre
VOC: 500g/litre
Touch Dry: 2 Hours
UN Number (Activator): UN1866
UN Number (Base): UN1263
Base Type: Solvent-Based
Suitable For Use On: Brick
Suitable For Use On: Stone
Suitable For Use On: Metal
Suitable For Use On: Concrete
Application Method: Roller
Components: 2K
Usages: High Traffic
Product Usage Type: Topcoat
Fastest Delivery: Next Working Day
Colour Family: Purple
Colour Family: Yellow
Colour Family: Off-White
Colour Family: Black
Colour Family: White
Colour Family: Cream
Colour Family: Beige
Colour Family: Grey
Colour Family: Green
Colour Family: Blue
Colour Family: Red
Colour Family: Brown
Colour Family: Pink
Colour Family: Orange
Product Type: Polyurethane Acrylic
Product Attributes: Tintable

Attachments

Download

Data Sheet

Download

Safety Data Sheet (Base)

Download

Safety Data Sheet (Activator)

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Sid on 2024-08-28 09:35:34	Question: Could this be applied to a sanded plywood substrate for high foot traffic ramp? What are the flexibility characteristics of this paint once cured? thanks, sid
	Answer from Rawlins’ Technical Team: No, for plywood this product wouldn't be suitable. Assuming the plywood is lightly abraded, clean, dry, sound and prepared as detailed in the technical datasheet, you could consider Coo-Var High Performance Primer followed by 2 coats of Coo-Var ProGrip Heavy Duty Two Pack Anti-Slip Floor Paint, to leave a hardwearing, aggregated, off-gloss finish for heavy trafficked areas.

Phil on 2023-10-19 21:51:24	Question: Is it UV stable - won't yellow if the sun is on it?
	Answer from Rawlins’ Technical Team: This product does state that is is non yellowing which indicates good colour retention, however we don't have any testing results for UV protection so couldn't confirm if this would be suitable.

Matt Parker on 2019-04-30 08:07:20	Question: Hi, is the paint ready mixed or do you have to add harder and thiners?
	Answer from Rawlins’ Technical Team: Blackfriar Professional High Traffic Floor Paint is a 2 pack epoxy coating so a 5lt is supplied in 2 tins - 1 tin of base and a smaller tin of activator. You should add the activator to base container and mix thoroughly for at least 5 minutes until product is smooth and even. Allow to rest 5 minutes before using

Robbie Thorne on 2019-04-03 08:54:10	Question: I am considering using "Blackfriars High Traffic Paint" on a car parking bay. The 6mm asphalt surface course is old so existing oils on the surface course should not be a problem. Question: Does your product contain MMA which seems to be a prefered additive? Alternatively do you have any suggestions?
	Answer from Rawlins’ Technical Team: Blackfriar Professional High Traffic Floor Paint is not suitable for asphalt, instead we would suggest 703 MMA Flexible Anti-Slip Coating assuming the surface is not currently painted.

gary on 2016-03-14 07:12:11	Question: how does this product deal with (skydrol) aircraft hydraulic fluid, which are phosphate ether based? and what floor preparation is required? chemical /mechanical? do you offer product solutions to floors that require sealing first i.e concrete saturated in fluid
	Answer from Rawlins’ Technical Team: There has been no testing carried out on Blackfriar Professional High Traffic Floor Paint for Skydrol exposure but our 310 Chemical Resistant Coating and 304 HD Epoxy Floor Coating have both been tested for full immersion. Under fully immersed conditions (i.e. constant contact/exposure) 304 would require re-coating after 1-2 years and 310 would require coating after 5-10 years. Concrete should be a minimum of 21 days old and/or the residual moisture content below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes etc. Blow holes and defective concrete can be made good using 201 Epoxy Repair Mortar. Suitable mechanical treatment such as vacuum grit blasting of suitable diamond floor grinding is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating. A coat of 401 Epoxy Floor Primer is recommended on absorbent concrete surfaces. Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.

IMPORTANT SHIPPING & DELIVERY INFORMATION

Blackfriar Professional High Traffic Floor Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Blackfriar Professional Oil Tolerant Primer

We no longer stock this product, but can recommend Coo-Var Oil Tolerant Primer as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113...

Shop now

In stock

Floor Application Kit

Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish. Each kit contains: 12" Roller,...

£101.80 (incl. VAT)

Shop now

In Stock and Available for Delivery

Follow us on:

Blackfriar Professional High Traffic Floor Paint

Blackfriar Professional High Traffic Floor Paint

Product customisation

Your customization: Chosen Colour: Ready Mixed - Grey

Data sheet

Questions

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION

Blackfriar Professional Oil Tolerant Primer

Floor Application Kit