- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Hammer Finishes QAD are used to produce an attractive and durable special effect hammer finish, which will hide imperfections on marked, pitted, or uneven surfaces of all types.
- Excellent drying gloss, adhesion and weathering properties
- Available in a range of colours with an attractive hammer finish
- For application on a wide variety of substrates
- Temperature resistant up to 80°C
Description
HMG Hammer Finishes QAD are used to produce an attractive and durable special effect hammer finish, which will hide imperfections on marked, pitted, or uneven surfaces of all types.
Non-cell (air dry acrylic) are the most popular general purpose hammer finish for application on a wide variety of substrates, offering excellent drying gloss, adhesion and weathering properties.
For a high performance, rapid curing stoving enamel please see HMG Stoving Enamel Hammer Finish.
Click To Jump To Section:
- Features & Benefits
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Important Instructions Before Use
- Health & Safety
Features & Benefits
- Easy to use
- Quick drying - Fully Cured in 24 hours @20°C
- Temperature resistant up to 80°C
- Available in a wide colour range
- For spray application on metal surfaces
Film Thickness Range And Coverage
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Gravity Gun: | 50 µm | 100 µm | |
| Pressure Pot: | 50 µm | 100 µm | |
| Compliant Spray Gun: | 50 µm | 100 µm | |
Coverage: 20m²/litre @ 40 microns dft.
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness
- These values are a guide only and are not to be used as specifications
- Film thickness will vary depending on actual use and specification
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness
Drying Times
| Drying Times At 20°C | |||
|---|---|---|---|
| Touch Dry: | 30 minutes | ||
| Hard Dry: | 4 - 6 hours | ||
| Dry To Recoat: | 10 minutes minimum - 18 hours maximum | ||
| Fully Cured: | 24 hours | ||
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants
Application Methods
| Technical Data | |||||
|---|---|---|---|---|---|
| Gravity Gun | Pressure Pot | Compliant Spray Gun | |||
| Mixing Ratio: | Base 85 - 95% | Base 85 - 95% | Base 85 - 95% | ||
| Thinner 5 - 15% | Thinner 5 - 15% | Thinner 5 - 15% | |||
| Thinner Options: | Thinner 2621 | Thinner 2621 | Thinner 2621 | ||
| Thinner 2622 | Thinner 2622 | Thinner 2622 | |||
| Viscosity: | 30 - 40 secs B4 cup | 30 - 40 secs B4 cup | 30 - 40 secs B4 cup | ||
| Spray Gun Setup: | 1.6 - 1.8 | 1.6 - 1.8 | 1.0 - 1.2 | ||
| Number Of Coats (Guide Only): | 1 - 2 coats | 1 - 2 coats | 1 - 2 coats | ||
| Flash Off: | 10 minutes @20°C | 10 minutes @20°C | 10 minutes @20°C | ||
For further information on mixing ratios please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected].
Important Instructions Before Use
- Read and follow SDS, TDS and label instructions
- Stir all paints thoroughly before use
- Always use the same batch number on the same job
- Check colour and sheen prior to application
- Filter the product immediately before use
- Reduce emissions and maintain quality by replacing tin lid after use
- If in any doubt, please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Health & Safety
- Refer to the Safety Data Sheet in the attachments section above and tin label prior to use
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a non-combustible container with a tight fitting lid
Product Details
7662-908304
Data sheet
- Manufacturer
- HMG paints Ltd
- For Use On
- Metal
- Single, Two or Three Pack
- Single
- Pack Size
- 1L, 2.5L, 5L, 20L
- Mixing Ratio
- Base 85-95% - Thinner 5-15%
- Application
- Spray
- Touch Dry (at 20°C)
- 30 min
- Dry to Recoat (at 20°C)
- 10min Minimum - 18hrs Maximum
- Fully Cured (at 20°C)
- 24 Hours
- Coverage
- 20m²/litre @ 40 microns dft
- Recommended Thinner/Cleaner
- Thinner 2621 - Thinner 2622
- Density
- 0.983g/cm³ (Contains Lead 1.023g/cm³)
- Solids by Volume
- 47.8% (Contains Lead 51.5%)
- VOC
- 0.54kg/l
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
Store between 5°C - 25°C. When not in use, cans must be kept sealed - Recommended Dry Film Thickness
- 50µm
- Recommended Wet Film Thickness
- 100µm
- UN Number
- UN1263
- Specific Gravity
- 0.96
- Viscosity
- 200mPas
- Hard Dry
- 4 - 6 Hours @20°C
- Flashpoint
- 4°C
- Colour(s)
- Standard Colours
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Finish
- Hammered
- Application Method
- Spray
- Manufacturer
- HMG Paints LTD
- Product Usage Type
- Topcoat
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Orange
- Colour Family
- Black
- Colour Family
- Metallic
- Colour Family
- Gold
- Colour Family
- Copper
- Colour Family
- Bronze
- Colour Family
- Stone
Questions
Question about the product
Rob
on
2021-12-06 14:07:29
| Question:
Does this need an undercoat on bare steel? or is it an undercoat and top coat? For some steel site boxes |
Answer from Rawlins’ Technical Team:
Assuming the bare steel is clean, dry, sound and prepared as detailed in the technical data sheet, the substrate should be primed first with HMG HB48 Primer. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Hammer Finish QAD is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT