Follow us on:

Fosroc Renderoc HB45 | High Strength Concrete Reinstatement Mortar
Fosroc Renderoc HB45 | High Strength Concrete Reinstatement Mortar

Fosroc Renderoc HB45

2198000
FOS8010

Fosroc Renderoc HB45 is a high performance, fibre reinforced, high build, high strength concrete reinstatement mortar, applicable by hand or wet spray, suitable for repair methods 3.1, 3.3, 4.4, 7.1, 7.2 as defined by BS EN 1504-3.

  • Specifically developed for the repair of columns and beams, but because of its medium fresh wet density, is also suitable for soffit repairs
  • For the reinstatement of reinforced concrete where low permeability characteristics are required and where higher compressive strength is a consideration

Where compatibility with lower strength concrete is required, Renderoc HB30 should be used.

Size
£95.93(incl. VAT)
£79.94(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

questions 1 question about the product
Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Supplied as a ready to use blend of dry powders requiring only the site addition of clean water to produce a highly consistent, lightweight repair mortar
  • Based on Portland cements, graded aggregates lightweight fillers, fibres and chemical additives which provide a mortar with good handling and finishing characteristics while minimising water demand
  • Exceptional handling characteristics - easy to finish
  • High-build applications possible while maintaining higher compressive strengths — fewer layers
  • Frequently obviates the need for formwork
  • Polymer-modification provides extremely low permeability to water, carbon dioxide and chlorides
  • Exceptional system of shrinkage compensation provides long-term dimensional stability
  • One component, pre-bagged to overcome site-batched variations
  • Contains no chloride admixtures
  • Suitable for use with cathodic protection systems

Uses

  • Specifically engineered for vertical and overhead repair work
  • Can be applied in sections up to 80 mm thickness in vertical locations and up to 70 mm thickness in overhead locations in a single application without formwork
  • Thicker sections can be achieved by the use of formwork or can be built up in layers
  • Deep pockets can sometimes be filled in a single application dependent on the configuration of the pocket and the volume of exposed reinforcing steel
  • Can be quickly and efficiently applied by the wet spray technique



Application Notes


  • Reinforcing steel can be primed with one full coat of Nitoprime Zincrich Plus prior to application
  • Concrete can be primed by scrubbing Renderoc Primer slurry into the surface
  • In exceptional circumstances, e.g. where a substrate/repair barrier is required or where the substrate is wet or likely to remain permanently damp, Nitobond EP bonding aid should be used
  • A forced-action mixer is essential. Mixing in a suitably sized drum using an approved Renderoc Mixing Paddle (MR4) with a slow speed (400/500 rpm) heavy-duty drill is acceptable for the occasional one-bag mix
  • Apply by gloved hand or trowel
  • Additional build-up can be achieved by application of multiple layers. The surface of the intermediate layers should be comb scratchkeyed and cured with Nitobond AR
  • Renderoc HB45 can be quickly and efficiently applied by the wet spray technique. In circumstances where large areas of repair are required, the rapid placement and higher build attainable by this method offer economic advantages over hand-trowelling. The resultant repair also offers a generally more dense compound with enhanced mortar/substrate bond characteristics
  • In cold conditions down to 3°C, the use of warm mixing water (up to 30°C) is advisable to accelerate strength development. At ambient temperatures above 35°C, the material should be stored in the shade and cool water used for mixing
  • The use of Nitobond AR, sprayed on to the surface of the finished mortar in a continuous film, is recommended. A low pressure atomising sprayer is essential for applying the Nitobond AR
  • Large areas should be cured as trowelling progresses (0.5m2 at a time) without waiting for completion of the entire area
  • The Dekguard range of protective, anti-carbonation coatings products may be applied over the repair area without prior removal of the Nitobond AR curing membrane
  • Should be removed from tools, equipment and mixers with clean water immediately after use. Cured material can only be removed mechanically
  • Yield: Approximately 14 litres / 25 kg bag (approximately 1.4 m² at 10 mm thickness)
  • The material should not be applied at less than 10 mm thickness

Note: the actual yield per bag will depend on the consistency used. The yield will be reduced if the material is applied by a spray technique.



Limitations


  • Should not be used when the temperature is below 3°C and falling
  • Free-fall mixers must not be used. Mixing of part bags should never be attempted
  • Due to the nature of Renderoc HB45, the product should not be used in areas subjected to traffic (in these circumstances, Renderoc S should be considered)
  • Should not be exposed to moving water during application
  • Exposure to heavy rainfall prior to the final set may result in surface scour
  • Renderoc HB45 is non-flammable
  • As with other ‘one pack’ repair mortars, Renderoc HB45 may exhibit satisfactory handling characteristics even though inadequately mixed. This will result in a significantly lower level of performance or possible failure. It is therefore essential that mixing instructions are strictly adhered to with particular emphasis on the quantity of water used and the time of the mixing operation



Product Details
8010-912780

Data sheet

Manufacturer
Fosroc
For Use By
Professional Use
For Use On
Concrete
Application Method
Gloved hand, trowel, spray
Single, Two or Three Pack
Single
Pack Size
25KG
Minimum Applied Thickness
10mm
Maximum Applied Thickness
70mm (Overhead)
80mm (Vertical)
Coverage
Approximately 14 litres / 25 kg bag (approximately 1.4 m² at 10 mm thickness)
Recommended Thinner/Cleaner
Water
Flexural Strength (at 20°C)
7.5 MPa @ 28 days
Shelf Life (from date of manufacture)
12 months
Resistance to chemicals
The low permeability of Renderoc HB45 severely retards chemical attack in aggressive environments. The cured mortar is impermeable to acid gases, waterborne chloride ions and oxygen.
Drying time
Initial set: 3 hours
Final set: 5 hours
Compressive Strength
@ 1 Day 20 MPa
@ 28 Days 50 MPa
Suitable For Use On
Concrete
Application Method
Spray
Application Method
Trowel
Application Method
Hand
Manufacturer
Fosroc
Usages
Cementitious Repair Systems
Product Usage Type
Mortar
Product Range
Renderoc
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)
questions Nick Calvert on 2023-04-18 14:09:00
Question: 

Any issues in using this product in confined areas?

Answer from Rawlins’ Technical Team:

Please can you provide more information on the project requirements to [email protected]

IMPORTANT SHIPPING & DELIVERY INFORMATION

Fosroc Renderoc HB45 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
Fosroc Ancillaries | Application Tools For Fosroc Products

Fosroc Ancillaries

Fosroc Ancillaries are a range of application tools and accessories for use when applying Fosroc products.  Range Includes: Fosroc Sealant Mixing Paddle, Fosroc Thioflex Follower Plate, Fosroc Polyurea Accessories Please see below for detailed information and order references where applicable

Price £59.04 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Fosroc Nitobond AR | Polymer Emulsion Bonding Agent

Fosroc Nitobond AR

Fosroc Nitobond AR is a single component polymer emulsion and recommended primer for the Renderoc cementitious repair systems. Nitobond AR can be used as a curing membrane and also a concrete surface sealer in non-traffic areas May also be used as an economical dust proofer and surface sealer for non-trafficked cementitious surfaces...

Price £159.06 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Fosroc Nitobond EP | Epoxy-Resin Concrete Bonding Agent

Fosroc Nitobond EP

Fosroc Nitobond EP is a 100% solids solvent-free epoxy resin containing pigments and fine filler. Used for bonding new cementitious mortars and screeds including Patchroc GP and Paveroc to existing cementitious surfaces. Ideal for extensions and repairs to concrete in factories, loading bays, trucking aisles, bridges, roads, bonded or...

Price £125.54 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Fosroc Nitoprime Zincrich Plus | Single Component Zinc Primer

Fosroc Nitoprime Zincrich Plus

Fosroc Nitoprime Zincrich Plus is the recommended anti-corrosion primer for exposed steel reinforcement for use with Fosroc concrete repair mortars. Fully compatible with all Renderoc mortars and fluid micro-concretes Complies with LU Standard 1-085 ‘Fire Safety Performance of Materials’. BS EN 1504-7: Reinforcement corrosion protection...

Price £63.19 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Fosroc Renderoc Primer | Polymer / Cement Slurry Bonding Agent

Fosroc Renderoc Primer

Fosroc Renderoc Primer is a high performance polymer/ cement slurry primer for use in conjunction with Fosroc cementitious repair materials. Two component cementitious slurry material comprising specially selected cementitious powders and liquid polymer additives The primer facilitates bond strengths conforming to the classification of the...

Price £31.90 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery