- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Fosroc Paveroc is a high performance reinstatement mortar for the reinstatement or resurfacing of large areas of concrete pavements, ramps and floors to avoid the full depth replacement of bays.
- May be used internally and externally including areas subject to heavy trafficking
- Suitable for repair methods 3.1, 3.2, 4.4, 7.1, 7.2 as defined by BS EN 1504-3
Paveroc can be used in conjunction with Fosroc Hardtop S for the repair of floors with a dry shake floor surfacing.
Quick Links - Click To Jump To Section:
Features & Benefits
- Supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent repair mortar
- Based on Portland cements, graded aggregates, and chemical additives providing a mortar with good handling characteristics while minimising water demand
- Low water requirement ensures good strength gain and long-term durability
- Alkaline in nature and will protect embedded steel reinforcement
- Long open time - applicable to large bay areas
- High strength, abrasion and weather resistance
- One component, pre-bagged to overcome site-batched variations
- Excellent bond to the concrete substrate
- Shrinkage compensated
- Contains no chloride admixtures
- Designed for horizontal use
- Please refer to the Product Data Sheet for full details of:
- Standards compliance
- Specification Clause
- Properties
- Application Instructions
- Storage
- Health and Safety
Application Notes
- To prime reinforcing steel, apply one full coat of Nitoprime Zincrich Plus and allow to dry before continuing
- Prime concrete using Nitobond EP, scrubbed into the surface with a suitable stiff nylon-type brush
- A forced-action mixer is essential. Mixing in a suitably sized drum using an approved Renderoc Mixing Paddle (MR4) with a slow speed (400/500 rpm) heavy-duty drill is acceptable for the occasional one-bag mix
- While the Nitobond EP is still tacky, apply the mixed Paveroc evenly by trowel and tamp in place with a wood float
- May be applied at thicknesses 12mm - 100mm. Thicker sections can be built up in layers
- In cold conditions down to 5°C, the use of warm mixing water (up to 30°C) is advisable to accelerate strength development. At ambient temperatures above 35°C, the material should be stored in the shade and cool water used for mixing
- In common with all cementitious materials, it must be cured immediately after finishing in accordance with good concrete practice. The use of Concure WB, sprayed on to the surface of the finished mortar in a continuous film, is recommended
- Nitoflor FC products may be applied over the repair area after prior removal of the curing membrane generally after 3 days
- Paveroc should be removed from tools, equipment and mixers with clean water immediately after use. Cured material can only be removed mechanically
- Coverage and yield: Approximately 11.5 litres / 25 kg bag (approximately 0.9 m² at 12 mm thickness)
Limitations
- Where a rapid return to service is required when patching small areas (>4m2 ) of concrete pavements and floors, the use of Patchroc GP is suggested instead of Paveroc
- Should not be used when the temperature is below 5°C and falling
- Should not be exposed to moving water during application. Exposure to heavy rainfall prior to the final set may result in surface scour
- Free-fall mixers must not be used. Mixing of part bags should never be attempted
- As with other ‘one pack’ repair mortars, the product may exhibit satisfactory handling characteristics even though inadequately mixed. This will result in a significantly lower level of performance or possible failure. It is therefore essential that mixing instructions are strictly adhered to with particular emphasis on the quantity of water used and the time of the mixing operation
Data sheet
- Manufacturer
- Fosroc
- For Use By
- Professional Use
- For Use On
- Concrete Floors
- Application Method
- Trowel, float
- Single, Two or Three Pack
- Single
- Pack Size
- 25KG
- Minimum Applied Thickness
- 12mm
- Maximum Applied Thickness
- 100mm
- Coverage
- approximately 0.9 m² at 12 mm thickness
- Compressive Strength (at 20°C)
- @ 1 Day 20 MPa
@ 7 days 45 MPa
@ 28 Days 65 MPa - Min. Application Temperature
- 5°C
- Shelf Life (from date of manufacture)
- 12 months
- Resistance to chemicals
- The low permeability of Paveroc severely retards chemical attack in aggressive environments. The cured mortar is impermeable to acid gases, waterborne chloride ions and oxygen.
- Dry for Light Traffic (at 20°C)
- (Pedestrian)
18 hours @ 10°C
12 hours @ 20°C
8 hours @ 30°C - Dry for Full Traffic (at 20°C)
- (Vehicular)
36 hours @ 10°C
24 hours @ 20°C
16 hours @ 30°C - Drying time
- Initial set: 3.5 hours
Final set: 5.0 hours - Working Time
- 60 minutes @ 10°C
55 minutes @ 20°C
30 minutes @ 30°C - Suitable For Use On
- Concrete Floors
- Application Method
- Trowel
- Application Method
- Float
- Manufacturer
- Fosroc
- Usages
- Cementitious Repair Systems
- Product Usage Type
- Mortar
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Fosroc Paveroc is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Fosroc Concure WB
Fosroc Concure WB is a water based concrete curing compound based on a low viscosity wax emulsion. For use as a spray applied membrane to retain moisture in concrete for effective curing. Suitable for all general concreting applications and of particular benefit for large area concrete surfaces, such as airport runways, roads and...
Fosroc Ancillaries
Fosroc Ancillaries are a range of application tools and accessories for use when applying Fosroc products. Range Includes: Fosroc Sealant Mixing Paddle, Fosroc Thioflex Follower Plate, Fosroc Polyurea Accessories Please see below for detailed information and order references where applicable
Fosroc Nitobond EP
Fosroc Nitobond EP is a 100% solids solvent-free epoxy resin containing pigments and fine filler. Used for bonding new cementitious mortars and screeds including Patchroc GP and Paveroc to existing cementitious surfaces. Ideal for extensions and repairs to concrete in factories, loading bays, trucking aisles, bridges, roads, bonded or...
Fosroc Nitoprime Zincrich Plus
Fosroc Nitoprime Zincrich Plus is the recommended anti-corrosion primer for exposed steel reinforcement for use with Fosroc concrete repair mortars. Fully compatible with all Renderoc mortars and fluid micro-concretes Complies with LU Standard 1-085 ‘Fire Safety Performance of Materials’. BS EN 1504-7: Reinforcement corrosion protection...
Fosroc Nitoflor Hardtop S
Fosroc Nitoflor Hardtop S surface hardening compound is a quality controlled, factory blended powder which is ready to use on site. It consists of special hard wearing aggregates selected for their physical properties of abrasion and wear resistance, Portland cement and special additives to improve workability. Cures to provide a dense, non...