Follow us on:

Sherwin-Williams Epo-Phen FF - Special Order

Sherwin-Williams Epo-Phen FF - Special Order

Epo-Phen FF - Special Order
SHE8123

Sherwin-Williams Epo-Phen FF - Special Order coating is a flake-filled (MIO) amine cured epoxy phenolic novolac formulated for use under thermal insulation at elevated or cryogenic temperatures and for immersion service in water and hydrocarbons such as gasoline, fuel oil, and diesel fuel. 

  • Temperature resistant to 218°C (425°F), constant;  232°C (450°F) intermittent (dry service)
  • Self priming
  • Chemical resistant
  • Please note: This product in a 20L pack size is made to order subject to a minimum order quantity of 200L and an extended lead time of 28 days
  • For the readily available 5L pack size please see Sherwin-Williams Epo-Phen FF
Colour
Size
Finish
£701.88(incl. VAT)
£584.90(ex. VAT)
Quantity
Please choose your colour
This Combination may be Subject to Extended Lead Times

The minimum purchase order quantity for the product is 10.

No queries yet, leave the first!
Description

Sherwin-Williams Epo-Phen FF  coating is a flake-filled (MIO) amine cured epoxy phenolic novolac formulated for use under thermal insulation at elevated or cryogenic temperatures and for immersion service in water and hydrocarbons such as gasoline, fuel oil, and diesel fuel. 

Features & Benefits

  • Temperature resistant to 218°C (425°F), constant;  232°C (450°F) intermittent (dry service)
  • Self priming
  • Chemical resistant

The micaceous iron oxide (MIO) provides:

  • High temperature resistance
  • Film reinforcement
  • One coat, high build application
  • Improved edge protection

Recommended Uses

  • Steel and stainless steel tanks and piping under insulation
  • Non-insulated structural steel and piping subjected to chemical or abrasion attack
  • Use in areas subject to wet/dry cycling up to 149°C (300°F)
  • Use in areas where temperature resistance up to 232°C (450°F) is required (dry service)
  • Acceptable for use in immersion service at elevated temperatures for fresh water and distilled water 99°C (210°F)
  • Suitable for storage of gasoline, fuel oil, diesel fuel, and other similar hydrocarbon cargos
  • Not qualified for potable water immersion
  • Water and wastewater facilities
  • Wind tower gearbox lining

Performance Tips

Stripe coat crevices, welds, and sharp angles to prevent early failure in these areas.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle.

Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, roughness or porosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive film build.

For Immersion Service: (if required) Holiday test in accordance with ASTM D5162 for steel, or ASTM D4787 for concrete.

Excessive reduction of material can affect film build, appearance, and adhesion.

Do not mix previously catalyzed material with new.

Do not apply the material beyond recommended pot life. In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with Reducer #15.

Temperatures above 25°C (77°F) will shorten the pot life.

Do not apply over 225 microns (9.0 mils) total dft when used in service above 149°C (300°F).

Not recommended for potable water immersion.

Acceptable for insulation to be applied over the coating, after the coating has reached it's dry to touch time.

Refer to Product Information sheet for additional performance characteristics and properties.

Product Details
8123-915951

Data sheet

Manufacturer
Sherwin-Williams
For Use By
Industrial Use
For Use On
Steel
Application Method
Brush, Roller, Spray
Sheen
Semi Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
20L
Application
Brush, Roller, Spray
Coverage
3.0 - 3.9m² per litre
Solids by Volume
70% ± 2%
Shelf Life (from date of manufacture)
24 months, unopened Store indoors at 4.5°C (40°F) to 38°C (100°F)
Touch Dry
3 hours
UN Number (Activator)
UN3066
UN Number (Base)
UN1263
Fully Cured
7 days
Solids by Weight
85% ± 2%
Base Type
Solvent-Based Epoxy
Suitable For Use On
Steel
Finish
Semi-Gloss
Application Method
Brush
Application Method
Roller
Application Method
Spray
Product Usage Type
Tank Lining
Product Range
Epo-Phen
Colour Family
Grey
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Sherwin-Williams Epo-Phen FF - Special Order is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT