303 WG Epoxy Floor Paint is a fast curing, high performance, water dispersible epoxy coating for the protection and decoration of floors and walls. It is designed to be used in lower temperatures or when a fast return to service is required. 303 WG Epoxy Floor Paint is user and environmentally friendly, containing no solvents and is very low odour during application.

303 WG Epoxy Floor Paint may be easily applied by brush, roller or airless spray, to provide a decorative, abrasion and chemically resistant coating of excellent durability. It leaves a smooth satin finish when dry.

Anti-slip properties of the coating can be enhanced by the addition of 508 Fine Particle Anti-Slip Additive can be added to the coating (200g per 5kg of 303 WG Epoxy Floor Paint) during mixing prior to application to produce an even and easily cleanable texture to the dried surface.

Note: For our ultimate slip resistance see 502 HD Anti-Slip Coating.

This product is for Professional Use Only.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Typical Properties
• Slip Resistance
• Coverage
• Surface Preparation
• Application
• Cleaning
• Curing
• Limitations
• Storage & Shelf Life
• Health & Safety

Features & Benefits

• Fast curing even at lower temperatures
• High performance
• Water dispersible
• Contains no solvents
• May be applied to dry or damp surfaces
• Available in a wide range of colours
• Low odour
• Semi-Gloss finish
• Easily applied
• Excellent resistance to water, oils, skydrol, petrol, dilute acids, alkalis and many solvents
• Very good adhesion to concrete
• Hygienic and easily cleaned
• Slip resistant options
• Suitable for use as a floor covering in food factories, abattoirs, dairies, laboratories, warehouses, etc.
• Can also be used as a chemically resistant coating for bund areas
• A hygienic, easily cleanable surface on walls, ceilings etc.
• Ideal where a fast return to service is required or when application must be carried out in lower temperatures

Typical Properties

Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.

Slip Resistance

Should a non-slip finish be required, 508 Fine Particle Anti-Slip Additive can be added to the coating during mixing prior to application to produce an even and easily cleanable texture to the dried surface.

Alternatively the 'Anti Slip' option can be selected when purchasing the product and the 250 micron grade of 508 Anti-Slip Additive will be added at 2.4% prior to receipt.

• 5kg unit - add 200g
  
• 15kg unit - add 600g

The above recommendation must only be used as a general guideline as the slip resistance of a cured resin coating can vary considerably due to many factors including: application technique, variations in film thickness, dispersion of the anti-slip texturing additive and the surface variations of the substrate and location to where it will be applied.

To obtain accurate PTV readings that are site specific (if required) it is strongly recommended that a slip assessment pendulum test is undertaken on each specific site after completion of the installation when the resin has fully cured.

Coverage

• A 5kg pack is sufficient to treat 10.0-12.5 m² of surface with the recommended two coat treatment, providing an overall d.f.t. of 200-250 microns (15kg pack pro rata)

Surface Preparation

Concrete:

• Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
• Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes
• Smooth concrete, or concrete with soft laitance, shall be mechanically treated by diamond grinding or grit blasting to provide a clean profiled surface
• Should this not be practicable then acid etching, although less preferable, is also an option
• Blow holes and defective concrete shall be made good using 201 Epoxy Repair Mortar
• Suitable mechanical treatment, such as vacuum grit blasting, is recommended to ensure a clean, uncontaminated substrate

Metal:

• Metal surfaces shall be wire brushed or power disced to remove any rust and loose or flaking material
• Grit blasting is recommended, where practical, for optimum performance
• Surface should then be immediately coated after preparation with 404 Epoxy Metal Primer

Wood:

• Wood surfaces shall be sanded to a smooth finish, and all previous coating removed
• Previously untreated wood shall be sealed with a coat of 401 Epoxy Floor Primer or 402 Damp Proof Coating

Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.

303 WG Epoxy Floor Paint will not tolerate movement in the substrate, if there is a possibility the substrate may flex, expand and contract, shift etc. use one of our flexible coatings - Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.

Priming:

• A primer coat of 401 Epoxy Floor Primer is recommended on concrete substrates
• This will facilitate application to damp and/or absorbent surfaces
• Apply the 401 Epoxy Floor Primer at a nominal rate of 0.2kg per m² in accordance with the product data sheet instructions
• Allow the primer to cure for a minimum period of 2 hours @ 20°C
• Ensure good ventilation during the drying/curing period

Mixing:

• Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform consistency is achieved
• The mixed material may be thinned by the addition of up to a maximum of 10% by volume of clean, potable water

Mixing Ratio:

• By Volume = 1 Base : 2.6 Curing Agent

Application

• Apply by brush, roller or airless spray at a nominal rate of 0.20 to 0.25kg/sq.m. per coat equivalent to a dry film thickness of 100-125 microns
• A minimum two coat treatment is recommended, applying subsequent coats after a minimum interval of 3 hours cure at 20°C
• Ensure good ventilation after application, as this speeds up the physical drying stage of the curing process
• Should a non-slip finish be required, 508 Fine Particle Anti-Slip Additive can be added to the coating during mixing prior to application to produce an even and easily cleanable texture to the dried surface
• Alternatively for a more aggressive anti-slip finish 504 Standard Anti Slip Aggregate can be scattered onto the first coat of 303 WG Epoxy Floor Paint whilst still wet
• The following day any excess aggregate may be swept from the surface using a clean brush prior to application of the second coat

Cleaning

• Clean equipment with 109 Tool Cleaner prior to curing of the coating

Curing

• Allow to cure for a minimum of 3 hours @ 20°C prior to light foot traffic access and 8 hours @ 20°C prior to vehicular trafficking
• 7 days cure @ 20°C is recommended prior to exposure to chemicals
• Good ventilation is essential for satisfactory curing of the coating
• Lower temperatures will extend the curing time

Limitations

• Do not apply to wet or uncured concrete surfaces
• Do not apply at temperatures of 3°C or less
• In poorly ventilated areas forced extraction must be provided

Storage & Shelf Life

• Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C
• 303 WG Epoxy Floor Paint has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions

Health & Safety

• Avoid contact of the material with skin and eyes
• Wear gloves and goggles
• Wash off splashes immediately with soap and water
• Any eye contamination must be rapidly irrigated with copious amounts of water, and immediate medical attention sought
• Please refer to Material Safety Data Sheet for additional Information
• 303 WG Epoxy Floor Paint shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]