- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2 pack, fast curing flexible coating in 4,400+ matt colours usually for Tarmac and Asphalt surfaces. Concrete surfaces may also be treated, following suitable preparation and priming. Ideal for use on surfaces such as parking bays, ramps, cycle paths, driveways, steps, etc.
- Readily available standard colours also available here
- Tough and abrasion resistant
- Colour stable
- Very good chemical resistance
- Cures at low temperatures (from 5°C)
- Light foot traffic after just 2 hours at 20°C
- Slip resistance properties may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate
- Images are for illustrative purposes only and may differ from the actual product
- This product is for Professional Use Only
Ordering References | Weight | Min. Order Quantity |
---|---|---|
RAL Classic and BS4800 Colours | 5KG | 10 |
RAL Classic and BS4800 Colours | 10KG | 5 |
BS381C, RAL Design, NCS | 5KG | 15 |
BS381C, RAL Design, NCS | 10KG | 8 |
Product customisation
Don't forget to save your customization to be able to add to cart702 MMA Flexible Floor Coating is a two pack, fast curing flexible coating usually for Tarmac and Asphalt surfaces. Concrete surfaces may also be treated, following suitable preparation and priming.
702 MMA Flexible Floor Coating is designed to provide a dust free, seamless floor finish with protective and decorative properties and allows a fast return to service.
Slip resistance properties may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.
This product is for Professional Use Only.
Recommended Uses:
- As a tough, durable and flexible coating for Tarmac, Asphalt and Concrete type surfaces. e.g. parking bays, ramps, cycle paths, driveways, steps, etc
Quick Links - Click To Jump To Section:
- Features & Benefits
- Typical Properties
- Coverage
- Surface Preparation
- Application
- Cleaning
- Curing
- Limitations
- Storage & Shelf Life
- Health & Safety
Features & Benefits
- Can be applied at temperatures as low as 5°C
- Tough and abrasion resistant
- Light foot traffic after just 2 hours at 20°C
- For Tarmac and Asphalt and Concrete surfaces
- Very good chemical resistance
- Two-pack
- Easily applied
- Hygienic and easily cleaned
- Flexible
Typical Properties
Technical Data | |
---|---|
702 MMA Flexible Floor Coating | |
Pot life @ 20°C: | 15 Minutes |
Pot life @ 10°C | 20 minutes |
Elongation at break: | 250% |
Adhesion to asphalt: | 3N/mm² (substrate failure) |
Temp. range during application: | 5°C to +40°C |
Temp. range during service: | -30°C to + 60°C |
Chemical Resistance | |
---|---|
Chemical | Resistance |
Dilute Acids and Alkalis | Excellent |
Oil | Excellent |
Petrol | Excellent |
Diesel | Excellent |
Vegetable Oils | Excellent |
Fruit Juices | Excellent |
Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.
Coverage
- A 10kg pack will be sufficient to coat an area of 10m² at a rate of 1kg/m²
Surface Preparation
- Asphalt and Tarmac surfaces must be clean, dry and free from contaminants
- New Asphalt and Tarmac must be allowed to ‘weather’ to ensure any excess oils are released
- Mechanical preparation is not normally necessary, however vacuum shot blasting can be employed to clean the surface should this be required, and will provide a better mechanical ‘key’ in heavy duty environments
Priming:
- No primer required for Asphalt and Tarmac surfaces
- Prime using 706 MMA Floor Primer on concrete (please refer to 706 MMA Floor Primer data sheet)
- Damp concrete surfaces can be primed using 709 MMA Damp Proof Primer – refer to product data sheet for full details
- Steel surfaces can be primed using 707 MMA Metal Primer – refer to product data sheet for full details
Mixing:
- 702 MMA Flexible Floor Coating is supplied as a two pack material consisting of the resin component, and the catalyst component
- Incorporate the catalyst component under mechanical stirring and mix for 1-2 minutes
Mixing Ratio:
- (% Catalyst by Weight) = 2
Application
- Apply 702 MMA Flexible Floor Coating using short nap perlon or smooth lambswool rollers at a nominal rate of 0.4 – 1.0kg/m² depending on substrate profile and desired thickness
- Should a slip resistant finish be required then broadcast 504 Standard Anti Slip Aggregate onto the first coat within 10 minutes of application
- Following a minimum of 1 hour, sweep off excess aggregate, and apply a second coat of 702 MMA Flexible Floor Coating.
Cleaning
- Clean equipment with 109 Tool Cleaner immediately after use
Curing
- Light Foot Traffic: 2 hours @ 20°C
- Full chemical resistance: 24 hours @ 20°C
Limitations
- Do not apply to damp substrates
702 MMA Flexible Floor Coating will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered
Storage & Shelf Life
- Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
- Adequate ventilation of the storage area should be provided
- Keep container tightly closed when not in use
- 702 MMA Flexible Floor Coating has a minimum shelf life of six months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
702 MMA Flexible Floor Coating flammable during application, so adequate safety precautions should be observed.
- Avoid contact of the material with skin and eyes
- Wear gloves and goggles
- Wash off splashes immediately with soap and water
- Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
- Please refer to Material Safety Data Sheet for additional information
- 702 MMA Flexible Floor Coating shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Rawlins Paints
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior & Exterior
- Water / Solvent Based
- Solvent
- For Use On
- Tarmac, Asphalt, Concrete
- Application Method
- Roller
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 10KG
- Fully Cured (at 20°C)
- 24 Hours
- Pot Life (at 20°C)
- 15 minutes
- Coverage
- 1m² per KG
- Max. Application Temperature
- 40°C
- Min. Application Temperature
- 5°C
- Touch Dry
- 2 Hours
- UN Number (Activator)
- UN3106
- UN Number (Base)
- UN1866
- Elongation at break
- 250%
- Base Type
- Solvent-Based
- Base Type
- MMA
- Suitable For Use On
- Concrete
- Suitable For Use On
- Tarmac
- Suitable For Use On
- Asphalt
- Finish
- Matt
- Application Method
- Roller
- Components
- 2K
- Product Usage Type
- Topcoat
- Product Category
- Paints
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Off-White
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Anthracite Grey
- Colour Family
- Dark
- Colour Family
- Cream
- Colour Family
- Stone
- Colour Family
- Beige
- Colour Family
- Lilac
- Colour Family
- Grey
- Colour Family
- Salmon
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
702 MMA Flexible Floor Coating - Special Colours is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
504 Standard Anti Slip Aggregate
504 Standard Anti Slip Aggregate is a specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased `anti-slip` properties in both dry and wet conditions to improve safety. Produces a rough, non-skid surface Hard wearing and chemical resistant Coloured Quartz Aggregate 0.4-0.8mm...
706 MMA Floor Primer
A rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds. Ideal for use as a rapid curing primer for concrete, steel, masonry,...
707 MMA Metal Primer
A rapid curing three-pack primer for steel, galvanised steel, aluminium, and unglazed ceramic tiles to be used prior to any of the MMA range of coatings, mortars, and screeds. Rapid cure, even at low temperatures - from as low as -30°C* Very good corrosion resistance Excellent adhesion Impervious to water Pre-packed units ready for use...
709 MMA Damp Proof Primer
Developed as a primer for damp concrete, being used prior to any of our MMA range of coatings, mortars, and screeds. Rapid cure, even at low temperatures - from as low as -30°C*. Very good chemical resistance. Excellent adhesion to damp concrete. Impervious to water. Pre-packed units ready for use. Easily applied. Can be overcoated...
109 Tool Cleaner
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product More...