- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
3-component insulating and coating system for concrete and steel surfaces. It can be use as insulating and toplayer applied on elements with dynamic weights arisen from pedestrians and vehicles traffic, especially as footbridges, vehicle bridges, bridge sidewalks, car parks, and ramps.
- See Construction of System below for component details
- To build your system:
- Select product type (primer, main coat, top coat)
- Pick a component product
- Choose a colour (Clear primer, coloured main-and-topcoat)
- Select a size
- Choose a finish
Product customisation
Don't forget to save your customization to be able to add to cartQuick Links - Click To Jump To Section:
- Features & Benefits
- Construction of System
- Surface Preparation
- Application - Main Coat
- Application - Topcoat
- Drying Time
Features & Benefits
- Anti slip, rough surface
- High abrasion and compression resistance
- Unaffected of salts
- UV-resistant, frost-resistant, waterproof
- Can be use as insulating and toplayer applied on elements with dynamic weights arisen from pedestrians and vehicles traffic, especially as:
- Footbridges and vehicle bridges
- Bridge sidewalks, car parks, ramps
Construction of System
- Mineral surface - concrete or similar, steel
- Primer
- For concrete surfaces:
- Temafloor 400
- Temafloor 200 (2-3 week lead time expected)
- Temafloor 220W (damp-resisting - 2-3 week lead time expected)
- For steel surfaces:
- For concrete surfaces:
- Non-slip sand
- Main coat – composite of colorful polyurethane resin Temafloor PU (2-3 week lead time expected) plus non slip sand in volumetric proportion 5:4
- Non slip sand
- Top coat – colourful polyurethane resin Temafloor PU UV (2-3 week lead time expected)
Surface Preparation
Concrete
Clean and prime surface according to technical card of primer (Temafloor 200, Temafloor 400 or Temafloor 220, 0.27-0.35 l/m3 ).
Add non-slip sand with grain between 0.4-0.8mm in amount around 1 kg/m2 when wet primer. Remove remains of the sand when it is dry.
Steel
Clean and prime surface according to technical card of primer Temabond ST 200.
Application - Main Coat
Mix Temafloor PU and non-slip sand according to table below.
Consumption of mineral-resin composite is around 0.6-0.7 l/m2 at 1 mm thick of layer.
Mixing ratio (Volume) proportion of non-slip sand and joint should be around 5:4.
Mixture is to be distributed by notch trowel then spike roller. Add non-slip sand (4-6 kg/m2) with grain 0.4-0.8 or 0.6-1.2mm depends on required thick and rough of layer. Let it dry minimum 12 hrs at temperature not less than 15°C.
Total thick of coat | Recommended grain of non-slip sand | % of fraction |
---|---|---|
3.0 - 5.0 mm | 0.4 - 0.8 | 100 |
Above 10 mm | 0.4 - 0.8 | 30 |
0.6 - 1.2 | 50 | |
2.0 - 3.0 | 20 | |
Attention: diameter the biggest grains of non-slip sand should not exceed 1/3 thick of main coat |
Application - Topcoat
Earlier prepared Temafloor PU UV according to its data sheet. Apply with portions on dry main coat and distribute by roller and rubber / steel trowel (consumption around 0.35 – 0.45 l/m² depends on required rough of layer).
Let it dry minimum 12 hrs at temperature not less than 15°C.
Steps | Amount of coats | Temafloor products |
---|---|---|
1 | 1-2 | Primer: Temafloor 200, Temafloor 400 or Temafloor 220 for concrete surfaces, Temabond ST 200 for steel surfaces |
2 | 1 | Non-slip sand 0.4 - 0.8 mm |
3 | 1 | Temafloor PU coat + non-slip sand 0.4 - 0.8 mm |
4 | 1 | Non-slip sand 0.4 - 0.8 mm or 0.6 - 1.2 mm |
5 | 1 | Temafloor PU UV coat |
Drying Time
Pedestrian traffic - after 24 hrs
Heavy traffic - after 7 days
Data sheet
- Single, Two or Three Pack
- Three-Pack
- Drying time
- Pedestrians’ traffic - after 24 hrs.
Heavy traffic - after 7 days. - Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Finish
- Gloss
- Finish
- Semi-Gloss
- Finish
- High Gloss
- Components
- 3K
- Product Usage Type
- Primer
- Product Range
- Temafloor
- Colour Family
- Grey
- Colour Family
- Red
- Colour Family
- Black
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tikkurila Temafloor 6 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT