- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Water based, fire resistant adhesive suitable for use with FirePro Beamclad and Rockwool Fire Duct Systems where glued joints or noggins are required.
- Can be used in conjunction with other Rockwool Stone Wool products where there is a requirement for a fire resistant adhesive
- Authorised for use in LUL surface and sub-surface premises and achieves fire ratings of up to 4 hours
276658 - 300ml Cartridge is available on 14-21 working days delivery only.
This specially created water-based and fire resistant adhesive with an approximate pH 11 is supplied in 17 kg plastic tubs and 300ml cartridges. It has been specially developed for fixing Rockwool fire protection systems as well as other suitable Rockwool products where a high quality, fire resistant adhesive is required.
Demonstrating its durability, the Firepro Glue is able to withstand a wide range of application temperatures. For example frost exposure does not remove the products curing ability and has been tested when applied to surfaces with temperatures of -10°C or rising.
The setting times of glue in moist air conditions is approximately 6-8 hours if the temperature is above freezing point, or in approximately 1 hour at 20°C. Firepro Glue in tubs must always be stirred before use to ensure a uniform product consistency. It is then easily applied using a pallet knife or trowel before pressing surfaces together. The application for the Firepro Glue cartridge is made using a sealant gun and spread evenly over the surface with a spatula or flat bladed tool.
Quick Links - Click To Jump To Section:
Features & Benefits
- LUL Approved
- Easy to apply
- Sets in as little as 4 hours
- Can be used from -10ºC upward
- Supplied in 17kg tubs and 300ml cartridges (in boxes of 12)
- Frost exposure does not remove curing ability
- Fire rating of up to 4 hours (When tested with Rockwool Fire Protection Systems)
Application Notes
- See product data sheet and installation guide for detailed application instructions
- Application of glue from tub is typically made by a pallet knife or trowel before pressing surfaces together. The product must always be stirred before use to ensure a uniform product consistency
- Application of glue from cartridge is made using a sealant gun and spread evenly over the surface with a spatula or similarly flat bladed tool
- Fixing boards together is supplemented by nails, pins or staples through noggin board joints and board joints
- Whilst steel surfaces may be acceptable when just moist to the touch, heavy water droplets, grease, scale oxide, dust etc should be removed prior to application
- Testing has shown that even if glued joints are immediately subjected to heavy frost exposure, the final glued joint strength is not threatened, but curing is retarded
- Glue fixed noggins must be allowed to set fully before any attempt is made to fix cover boards
- May be used to attach cover boards onto cured noggins (and in glued board joints), provided that a 24 hour interval is acceptable before further trades work on such protected steelwork
- Exhaustive testing has been made under various application conditions. All noggins fitted into steelwork should be cut to provide an interference friction fit of approximately 0.5mm. Excessive oversizing causing the noggins to bend should be avoided
- Noggins should be installed so as to be just proud of the flange tips. For web depths greater than 500mm ‘solid’ noggins or ‘T’ noggins Rockwool Beamclad must be used
- A nominal 0.5mm interference fit is recommended for all ambient conditions, but particularly for winter working. All noggin edges in contact with steelwork must be glued
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Data sheet
- Manufacturer
- Rockwool
- For Use By
- Professional Use
- Interior / Exterior Use
- Exterior Use
- For Use On
- Steelwork
- Application Method
- Pallet knife, trowel, sealant gun
- Single, Two or Three Pack
- Single
- Pack Size
- 17kg tubs and 300ml cartridges (in boxes of 12)
- Suitable For Use On
- Building Board
- Suitable For Use On
- Steel
- Application Method
- Trowel
- Application Method
- Sealant Gun
- Manufacturer
- Rockwool
- Product Usage Type
- Adhesive
- Product Range
- Firepro
- Fire Rating
- 240 Minutes
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Rockwool Firepro Glue is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Rockwool Beamclad System
Manufactured using high performing, noncombustible stone wool insulation, specially designed to provide fire protection to structural steel for periods of up to 4 hours. Offers contractors simple and economical fire protection solutions to the very real diversity of modern steel constructions Available in a plain or foil faced finish,...
Rockwool Fire Duct Section
Provides comprehensive performance for stability, integrity and insulation, for all ducts passing through fire-rated walls or floors. Fully tested to BS476-24 (duct types A and B) for preventing fire spread from one compartment to another. Three products are available in the Fire Duct Systems range, in a range of thicknesses: Fire Duct...
Rockwool Fire Duct Slab
Provides comprehensive performance for stability, integrity and insulation, for all ducts passing through fire-rated walls or floors. Fully tested to BS476-24 (duct types A and B) for preventing fire spread from one compartment to another. Three products are available in the Fire Duct Systems range, in a range of thicknesses: Fire Duct...