- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A hard-wearing flame-retardant topcoat with 4,400+ colours for application over Zeroflame Aquasteel WB+ Intumescent Coating:
- Class 0 fire rated finish on bare or previously painted non-combustible surfaces
- Hard wearing, water-based acrylic eggshell, matt or solvent-based gloss finish
- High coverage rates
Important!
- Should be used in most instances as one part of the following systems:
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Zeroflame Aquasteeel WB+ Finish is an exceptionally hard wearing decorative finish for application over Zeroflame Aquasteel WB+ Intumescent Coating and as a Class 0 fire rated finish on bare or previously painted non-combustible surfaces.
Aquasteel WB+ Finish is available as a water based acrylic eggshell or solvent based gloss finish. Both Eggshell, Gloss and Matt finishes are available in nearly all BS, RAL and NCS colours.
Apply at a rate of 12m² per litre/per coat for Eggshell and 14m² per litre/per coat for Gloss over Zeroflame Aquasteel WB+ Intumescent Coating, one coat is normally sufficient but for dark contrasting colours two may be required. Allow a minimum of 16 hours after the final coat of Aquasteel WB+ basecoat has been applied before applying topcoat.
Features and Benefits
- Easily applied by brush, roller or spray
- Hard wearing matt, eggshell or gloss finish
- High coverage and wide colour range
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Product Details
851-966340
Data sheet
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- Single, Two or Three Pack
- Single
- Application
- Brush, Roller, Spray
- Coverage
- 12m² per litre (Eggshell, Matt), 14m² per litre (Gloss),
- Touch Dry
- 4 hours
- Base Type
- Solvent-Based
- Base Type
- Water-Based
- Suitable For Use On
- Previously Painted Surfaces
- Finish
- Matt
- Finish
- Gloss
- Finish
- Eggshell
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Product Range
- Aquasteel WB+
- Fastest Delivery
- Next Working Day
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Dark
- Colour Family
- Stone
- Colour Family
- Lilac
- Colour Family
- Anthracite Grey
- Colour Family
- Salmon
- Colour Family
- Beige
- Colour Family
- Grey
Questions
Question about the product
P
on
2024-08-16 20:47:28
| Question:
I have a steel roof frame to paint in a commercial unit, it was painted before I bought the place and I'm not sure if it was done with a normal paint or fire safety paint. Do I need to strip back this paint before painting with intumescent paint or can I give it a rough sand with a 240 grit? If so, could you recommend how to strip back the original paint? Thanks. |
Answer from Rawlins’ Technical Team:
No, we wouldn't recommend this product. An intumescent paint system can only be over painted with the same manufacturers approved topcoats. In some instances we can offer an intumescent paint system that with a test for compatibility and adhesion can be applied over other coatings, but in most cases it would need to be removed back to bare metal. Please complete the steel form on the Thermoguard Fire Application Forms page and return. | |
|
Jessica
on
2022-01-24 16:03:07
| Question:
Hi, do you sell this in any smaller quantities than 2.5l? |
Answer from Rawlins’ Technical Team:
Unfortunately no, 2.5ltr is the smallest size. | |
|
Maurice Williams
on
2020-03-28 12:09:01
| Question:
Is this paint OK for an integral garage ceiling? If not, what would you recommend? |
Answer from Rawlins’ Technical Team:
We would need to know the level of fire protection you are required to achieve and what the ceiling is made from that is to be coated. Please contact our Technical Team on 0113 2455450 (option 2) with this information and they will be able to advise on a suitable system. | |
|
Fiona Murphy
on
2019-04-22 21:25:35
| Question:
I am currently painting an RSJ with waterbased intumescent paint and it isincredibly glutenous ,difficult to spread and the finish is really lumpy. What could cause this please? |
Answer from Rawlins’ Technical Team:
Intumescent paint is notoriously thick and not the most aesthetic of products to use. We would recommend the paint is kept in a warm place overnight before use and then it be mechanically stirred prior to application which should make it much more fluid and easier to use. | |
|
Darren
on
2018-04-05 15:27:08
| Question:
Is it possible to just use the eggshell finish coat over the top of a steel supporting girder previously coated in Hammerite to provide 30 min fire protection or does it specifically need the intumescent undercoat? |
Answer from Rawlins’ Technical Team:
The intumescent basecoat (Zeroflame Aquasteel WB+) must be applied first to achieve any level of fire protection. In this instance the steels would need to be completely stripped of Hammerite would need to be completely before application of Zeroflame Aquasteel WB+ and Zeroflame Aquasteel WB+ Finish. | |
|
Stephen
on
2018-03-17 10:12:23
| Question:
I want to paint a flat metal roof (lift car )that has been graffitied would this be any good? |
Answer from Rawlins’ Technical Team:
No, Zeroflame Aquasteel WB+ Finish is part of a fire protection system for structural steel and assuming you are not trying to achieve any level of fire protection we would instead recommend Rust-Oleum CombiColor, assuming this is the internal, underside of the metal roof and it had been previously painted before the graffiti attack. Clean graffiti off first as much as possible, you may require a stain blocking primer like Zinsser Cover Stain to be applied before the CombiColor finish if the graffiti is still visible. | |
|
Martyn Dobbing
on
2017-11-07 11:42:09
| Question:
Hi, we are currently having a loft conversion. To meet building regs we need to have fire doors leading on to the escape route stairs on all the floor with the house now being on 3 floors. My question is, will this paint turn my current doors into fire door. Meeting the building regs. Many thanks. |
Answer from Rawlins’ Technical Team:
No, for fire retardant products that upgrade the fire resistance of doors see Door Upgrade Kits. | |
|
Chris Burroughs
on
2017-10-19 08:28:42
| Question:
Hi
I am installing a log burner and the surrounding wall is finished with sand and cement, what paint would you recommend? |
Answer from Rawlins’ Technical Team:
Please refer to our blog post Painting the Walls around a Fireplace or Multi Fuel Stove for more details. | |
|
barbara lees
on
2017-01-23 19:17:49
| Question:
We are currently converting our garage and do not want plasterboard walls! the building office says if we use panelling it must be class 1 spread of flame. We would like to use mdf 9mm wall panelling sheets so what paint would you recommend to make them conform? |
Answer from Rawlins’ Technical Team:
| |
|
aubert
on
2015-12-13 12:50:40
| Question:
Is Zeroflame Aquasteel WB+ Finish suitable to paint over the render of a chimney hearth? |
Answer from Rawlins’ Technical Team:
No it isn't, we recommend using Thermoguard Wallcoat Smoke & Flame Retardant Topcoat. This product isn't heat resistant and may discolour over time if continually subjected to high temperatures, but it is a much safer alternative to standard emulsion. | |
|
Oliver Dew
on
2015-06-29 17:56:48
| Question:
Hi there, I was wondering if you can match Zeroflame Aquasteel WB+ Finish to any RAL or Pantone colour? Two colours I'm interested in are RAL 10A01 and Pantone warm gray u. |
Answer from Rawlins’ Technical Team:
We can mix Zeroflame Aquasteel WB+ Finish to most RAL, BS and NCS colours. We cannot produce Pantone colours but can offer the 10A01 you have asked for, this is actually in the BS 4800 colour range not RAL and is available to select as a standard colour from the options listed on the product on our website. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Zeroflame Aquasteel WB+ Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Zeroflame Fire Retardant Treatment
For use on bare, solid wood with a minimum thickness greater than 12mm. Soaks virtually ‘invisibly’ into the wood. Achieves Euroclass B s2 d0 (replaces UK Classes ‘0’ and ‘1’ BS 476 Part 6/7*). Can be overcoated for decorative purposes with waterborne, non-flammable stains, varnishes and paints. For internal and external use. Simple...
Price
£195.80
(incl. VAT)
In Stock and Available for Delivery
Zeroflame Aquasteel WB+
White thin-film waterbourne intumescent coating with new and improved formula to provide 30 and 60 minutes fire resistance on standard structural steel members in internal environments. It provides an easier and more efficient alternative to cladding steel members in plasterboard. New improved formula Achieves both 1/2 hour and 1 hour fire...
Price
£104.40
(incl. VAT)
In Stock and Available for Delivery
Zeroflame Fire Retardant Paint
A matt white, single-pack waterborne coating for wood that reduces ignitability for interior surfaces. Achieves Euroclass B s2 d0 (replaces UK Classes ‘0’ and ‘1’ BS 476 Part 6/7*). Can be overcoated with waterborne, non-flammable paints. Simple certificate application following purchase and application. Internal use. Can be applied by...
Price
£169.15
(incl. VAT)
In Stock and Available for Delivery
General Painting Application Kit
Provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects, including uPVC surfaces, walls, ceilings, and more. Click to jump down to...
Price
£12.08
(incl. VAT)
In Stock and Available for Delivery