- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2-pack Epoxy finish with 6,700+ colour options for solid colours and single-layer metallic finishes. Suitable for use on Steel surfaces primed with Selemix Epoxy Primers
- Suitable for the coating of equipment and machinery, especially those in an aggressive environment
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- Has a gloss finish and gives a hard and chemically resistant film
- Product can be purchased as a Two Component Pack, or as Base or Hardener only
- For faster curing please see Selemix 7-410 2K Epoxy Topcoat (Fast Curing)
- Please Note: Should not be used on exterior surfaces exposed to sunlight if a good level of colour and gloss stability is required
- For Professional Use Only
Product customisation
Don't forget to save your customization to be able to add to cartSelemix 7-410 2K Epoxy Topcoat is a 2-pack Epoxy finish for solid colours and single-layer metallic finishes. It has a gloss finish and gives a hard and chemically resistant film.
It is compatible with Selemix Epoxy Primers, giving a durable and hard wearing paint system.
Application can be by conventional or air-assisted airless spray.
It is suitable for the coating of equipment and machinery, especially those situated in an aggressive environment.
Please note: It should not be used on exterior surfaces exposed to sunlight if a good level of colour and gloss stability is required.
For Professional Use Only.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Surface Preparation
- Mixing
- Application Notes
- Theoretical Coverage
- Drying Times
- Health & Safety
Features & Benefits
- 2-pack Gloss Epoxy finish for solid colours and single-layer metallic finishes
- It is compatible with Selemix Epoxy primers, giving a durable and hard wearing paint system
- Suitable for use on Steel surfaces primed with Selemix Epoxy Primers
- Suitable for the coating of equipment and machinery, especially those in an aggressive environment
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- Product can be purchased as a Two Component Pack, or as Base or Hardener only
- For faster curing please see Selemix 7-410 2K Epoxy Topcoat (Fast Curing)
- Please Note: Should not be used on exterior surfaces exposed to sunlight if a good level of colour and gloss stability is required
- For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel (use a primer in corrosive environments):
- Machine sand with P80-120 discs and degrease
Selemix Epoxy Primers:
- Refer to Primer TDS for recoat time
Mixing
- Thoroughly mix paint before activating and check colour before use
Features | Conventional Spray | Air-Assisted Airless |
---|---|---|
By Weight: 7-410 Topcoat 9-010/9-011 Hardener |
1000 500 400-500 |
1000 500 400-500 |
By Volume: 7-410 Topcoat 9-010/9-011 Hardener 1-410/1-400 Thinner |
3 2 2-2.5 (65-80%) |
3 2 2-2.5 (65-80%) |
Viscosity (at 20°C): | 18-22 secs DIN4 | 18-22 secs DIN4 |
Pot Life (at 20°C): | 6-8 hours | 6-8 hours |
Mixing Ratio:
- Selemix 7-410 2K Epoxy Topcoat
- 3 parts base : 2 parts hardener
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
Application Notes
Features | Conventional Spray | Airless Spray |
---|---|---|
Spraygun Setup: |
Nozzle: Gravity: 1.3-1.4mm Suction: 1.6-1.8mm Pressure feed: 0.85-1.2mm |
Nozzle: 9-11 thou 0.23-0.28mm |
Air Pressure: |
HVLP: 2 Bar Standard: 2-3 Bar |
2.5 Bar |
Fluid Pressure: | N/A | 80-100 Bar |
Number of coats: | 2 | 2 |
Flash-off between coats: | 10-15 mins | 10-15 mins |
Drying: | Air dry or bake at 60°C for 60 mins | Air dry or bake at 60°C for 60 mins |
Flash-off before bake: | 10 mins | 10 mins |
Wet Film Thickness: | 130 microns (2 x 75-100µm) | 130 microns |
Dry Film Thickness: | 50 microns | 50 microns |
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
- 7.2-7.7m²/L at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C | |
---|---|
Dust Free | 30-40 mins |
Touch Free | 3-4 hours |
Tape Free | 12-18 hours |
Handleable | 6-8 hours |
Hard Dry | 12-18 hours or after bake |
Overcoating time |
Minimum: 3 hours Maximum: 24 hours by itself without sanding |
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times |
Health & Safety
- For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
- THIS PRODUCT IS FOR PROFESSIONAL USE ONLY
Data sheet
- Manufacturer
- Selemix
- For Use By
- Professional Use
- Water / Solvent Based
- Solvent Based
- For Use On
- Steel
Primed Surfaces - Sheen
- Gloss
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- 3 to 2
- Application
- Spray
Airless Spray - Touch Dry (at 20°C)
- 4 hours
- Pot Life (at 20°C)
- 6-8 hours
- Recommended Dry Film Thickness
- 50 microns
- Recommended Wet Film Thickness
- 130 microns
- UN Number (Activator)
- UN1263
- UN Number (Base)
- UN1263
- Hard Dry
- 12-18 hours or after bake
- Dust Dry (at 20°C)
- 30-40 minutes
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Primed Surfaces
- Finish
- Gloss
- Substrate
- Steel
- Substrate
- Painted / Primed Metal
- Usages
- High Chemical Resistance
- Usages
- Chemical Resistance
- Usages
- Atmospheric
- Usages
- Tough/Durable
- Usages
- Force Dry Compatible
- Product Usage Type
- Topcoat
- Technologies
- Solventborne
- Technologies
- 2K
- Application Methods
- Conventional
- Application Methods
- Airmix
- Application Methods
- Electrostatic
- Product Type
- Acrylic
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 4 hours
- Drying Properties
- Force Dry Compatible
- Resistance to
- Chemicals
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Selemix 7-410 2K Epoxy Topcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Selemix 7-410 2K Epoxy Topcoat (Fast Curing)
Fast-curing 2-pack epoxy finish with 6,700+ colour options for solid colours and single-layer metallic finishes. For steel surfaces primed with Selemix Epoxy Primers Suitable for the coating of equipment and machinery, especially those in an aggressive environment Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours...
Selemix 1-400 Slow Epoxy Thinner
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
Selemix 1-410 Epoxy Thinner
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only