- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
We no longer stock this product, but can recommend Selemix 7-413 2K Epoxy Primer as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Product customisation
Don't forget to save your customization to be able to add to cartSelemix 7-414 2K Epoxy Vinyl Primer is a fast drying tintable primer which may be used in a wet-on-wet system. It can be used over a wide range of substrates and can be recoated without sanding even after a long period.
For use on Steel, Cast Iron, Light Alloys & Previously Painted Surfaces on Machinery, Signage and Metal Fabrication.
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours.
*Note: RAL Pearl colours shown are approximations only - matches will not be exact.
For Professional Use Only.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Surface Preparation
- Mixing
- Application Notes
- Theoretical Coverage
- Drying Times
- Health & Safety
Features & Benefits
- Fast drying tintable primer which may be used in a wet-on-wet system
- It can be used over a wide range of substrates and can be recoated without sanding even after a long period
- For use on Steel, Cast Iron, Light Alloys & Previously Painted Surfaces
- Suitable for use on Machinery, Signage and Metal Fabrication
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- Product can be purchased as a Two Component Pack, or as Base or Hardener only
- For faster curing please see Selemix 7-414 2K Epoxy Vinyl Primer (Fast Curing)
- For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel (Blast Cleaned):
- Blast clean to ISO 8527-1 SA 2.5 with a blast profile of maximum 40 µm Rz.
- Note: A first coat of 7-413 Epoxy Primer is recommended before spraying a second coat with 7-414
Steel/Cast Iron:
- Machine sand with P80-120 discs and degrease
Light Alloys:
- Machine sand with P280-320 discs and degrease
Phosphated Steel:
- Abrade with SCOTCHBRITE® and degrease
Painted Surfaces:
- Machine sand with P240-320 discs and degrease
Do not use over wash primers or 1K synthetic primers.
Mixing
- Thoroughly mix paint before activating and check colour before use
Features | Conventional Spray |
---|---|
By Weight: 7-414 Primer (Tinted) 9-010/9-011 Hardener |
By Weight: 1000 100 400-500 |
By Volume: 7-414 Primer (Tinted) 9-010/9-011 Hardener 1-410/1-400 Thinner |
By Volume: 9 1 4-5 (45-55%) |
Viscosity (at 20°C): | 25-25 secs DIN4 |
Pot Life (at 20°C): | 8-10 hours |
Mixing Ratio:
- Selemix 7-414 2K Epoxy Vinyl Primer
- 9 parts base : 1 part hardener
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
Application Notes
Features | Conventional Spray |
---|---|
Spraygun Setup: |
Nozzle: Gravity: 1.6-1.8mm Suction: 1.8-2.0mm Pressure feed: 1.2-1.4mm |
Air Pressure: |
HVLP: 2 Bar Standard: 2.5-3 Bar |
Fluid Pressure: | N/A |
Number of coats: | 2 |
Flash-off between coats: | 10-15 mins |
Drying: | Air dry 2 hours at or bake at 60°C for 30-45 mins |
Flash-off before bake: | 10-15 mins |
Wet Film Thickness: | 150-200 microns |
Dry Film Thickness: | 40-50 microns |
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
- 4.5-5m²/L at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C | |
---|---|
Dust Free | 15-20 mins |
Handleable | 2-3 hours |
Hard Dry | 24 Hours |
Stoving | 30-45 minutes @60°C (according to film thickness) |
Overcoating time |
Minimum: 2 hours Maximum: 2 months without sanding on clean surface with any 2K Selemix Topcoat |
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times |
Health & Safety
- For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
- THIS PRODUCT IS FOR PROFESSIONAL USE ONLY
Data sheet
- Manufacturer
- Selemix
- For Use By
- Professional Use
- Water / Solvent Based
- Solvent Based
- For Use On
- Steel
Light Alloy
Painted Surfaces - Sheen
- Matt
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- 9 to 1
- Application
- Spray
- Pot Life (at 20°C)
- 8-10 hours
- Recommended Dry Film Thickness
- 40-50 microns
- Recommended Wet Film Thickness
- 150-200 microns
- UN Number (Activator)
- UN1263
- UN Number (Base)
- UN1263
- Hard Dry
- 24 hours
- Dust Dry (at 20°C)
- 15-20 minutes
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Base Type
- Epoxy Vinyl
- Suitable For Use On
- Steel
- Suitable For Use On
- Cast Iron
- Suitable For Use On
- Light Alloys
- Suitable For Use On
- Compatible Existing Coatings
- Suitable For Use On
- Phospated Steel
- Substrate
- Blasted Steel
- Substrate
- Painted / Primed Metal
- Substrate
- Cast Iron
- Substrate
- Light Alloys
- Substrate
- Phosphated Steel
- Substrate
- Steel
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Product Usage Type
- Primer
- Technologies
- Solventborne
- Technologies
- 2K
- Application Methods
- Conventional
- Application Methods
- Electrostatic
- Dry to Recoat (@ 20-25°C)
- 2 hours
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Selemix 7-414 2K Epoxy Vinyl Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Selemix 1-400 Slow Epoxy Thinner
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
Selemix 1-410 Epoxy Thinner
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
Selemix 7-413 2K Epoxy Primer
Tintable primer with 6,700+ colours and a fast drying time for use in a wet on wet system when recoated with 2K Topcoats. For use on Steel, Cast Iron, Aluminium, Light Alloys, GRP & Previously Painted Surfaces Good anticorrosive properties - Suitable for the finishing and protection of machinery, agricultural & construction...