- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2-pack polyurethane high-gloss finish in 6,700+ colours for coating machinery, agricultural and construction equipment, and many other industrial painting applications where a durable finish is required.
- Compatible with Selemix Epoxy and Polyurethane primers, giving a durable and hard wearing paint system
- For solid colours and single-layer metallic finishes
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- Product can be purchased as a Two Component Pack, or as Base or Hardener only
- Hammer Effects can be achieved by the additon of Selemix 6-540
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Product customisation
Don't forget to save your customization to be able to add to cartProfessional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Selemix 7-510 2K Polyurethane Topcoat is a 2-pack Polyurethane finish for solid colours and single-layer metallic finishes. It has a high gloss finish with good durability.
It is compatible with Selemix Epoxy and Polyurethane primers, giving a durable and hard wearing paint system. With Selemix 2K Polyurethane Direct Primer, the same hardener and thinner can be used in both primer and topcoat, giving a simple and efficient process.
Application can be by conventional or air-assisted airless spray.
Suitable for the coating of machinery, agricultural and construction equipment, and many other industrial painting applications where a durable, high gloss finish is required.
For Professional Use Only.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Surface Preparation
- Mixing
- Application Notes
- Theoretical Coverage
- Drying Times
- Health & Safety
Features & Benefits
- 2-pack Polyurethane finish for solid colours and single-layer metallic finishes
- Compatible with Selemix Epoxy and Polyurethane primers, giving a durable and hard wearing paint system
- Suitable for the coating of machinery, agricultural and construction equipment, and many other industrial painting applications where a durable, high gloss finish is required
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- Product can be purchased as a Two Component Pack, or as Base or Hardener only
- For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Painted Surfaces/Polyurethane or Polyester Fillers:
- Machine sand with P320-400 discs and degrease
Selemix Epoxy Primers or PU Primers:
- Refer to Primer TDS for recoat time
Mixing
- Thoroughly mix paint before activating and check colour before use
Features | Conventional Spray | Air-Assisted Airless |
---|---|---|
By Weight: 7-510 Topcoat 9-060 Hardener |
1000 300 350-400 |
1000 300 350-400 |
By Volume: 7-510 Topcoat 9-060 Hardener |
3.5 1 1.3-1.5 (35-40%) |
3.5 1 1.3-1.5 (35-40%) |
Viscosity (at 20°C): | 18-20 secs DIN4 | 18-20 secs DIN4 |
Pot Life (at 20°C): | 1.5 hours | 1.5 hours |
Mixing Ratio:
- Selemix 7-510 2K Polyurethane Topcoat
- 3.5 parts base : 1 part hardener
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
Application Notes
Features | Conventional Spray | Airless Spray |
---|---|---|
Spraygun Setup: |
Nozzle: Gravity: 1.3-1.4mm Suction: 1.6-1.8mm Pressure feed: 0.85-1.2mm |
Nozzle: 9-11 thou 0.23-0.28mm |
Air Pressure: |
HVLP: 2 Bar Standard: 2-3 Bar |
2.5 Bar |
Fluid Pressure: | N/A | 80-100 Bar |
Number of coats: | 2 | 2 |
Flash-off between coats: | 10-15 mins | 10-15 mins |
Drying: | Air dry or bake at 60°C for 30-40 mins | Air dry or bake at 60°C for 30-40 mins |
Flash-off before bake: | 10 mins | 10 mins |
Wet Film Thickness: | 130 microns | 130 microns |
Dry Film Thickness: | 50 microns | 50 microns |
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
- 7.2-7.5 m²/L at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C | |
---|---|
Dust Free | 10-15 mins |
Touch Free | 1-2 hours |
Tape Free | 16 hours |
Handleable | 4-6 hours |
Hard Dry | 10-16 hours or after bake |
Overcoating time |
Minimum: When Hard Dry Maximum: 24 hours by itself without sanding |
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times |
Health & Safety
- For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
- THIS PRODUCT IS FOR PROFESSIONAL USE ONLY
Data sheet
- Manufacturer
- Selemix
- For Use By
- Professional Use
- Water / Solvent Based
- Solvent Based
- For Use On
- Painted Surfaces
Primed Surfaces - Sheen
- High Gloss
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- 3.5 to 1
- Application
- Spray
Airless Spray - Touch Dry (at 20°C)
- 2 hours
- Pot Life (at 20°C)
- 1.5 hours
- Recommended Dry Film Thickness
- 50 microns
- Recommended Wet Film Thickness
- 130 microns
- UN Number (Activator)
- UN1263
- UN Number (Base)
- UN1263
- Hard Dry
- 10-16 hours or after bake
- Dust Dry (at 20°C)
- 10-15 minutes
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Primed Surfaces
- Finish
- High Gloss
- Substrate
- Painted / Primed Metal
- Usages
- High UV Resistance
- Usages
- Atmospheric
- Usages
- Tough/Durable
- Usages
- Force Dry Compatible
- Product Usage Type
- Topcoat
- Technologies
- Solventborne
- Technologies
- 2K
- Application Methods
- Conventional
- Application Methods
- Airmix
- Application Methods
- Electrostatic
- Product Type
- Polyurethane
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 2 hours
- Drying Properties
- Force Dry Compatible
- Product Attributes
- Tough / Durable
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Selemix 7-510 2K Polyurethane Topcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Selemix 1-470 Slow Direct Thinner
For use with selected products in the Selemix range including Selemix 2K Polyurethane Direct Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
Selemix 1-208 Slow Thinner
For use with selected products in the Selemix range including Selemix 2K Polyurethane Direct Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
Selemix 4-0500 2K Polyurethane Direct Primer
High build 2K polyurethane primer used in conjunction with Selemix 2K Acrylic and PU topcoats for a system suitable for the finishing and protection of machinery, agricultural and construction equipment, and many other industrial painting applications. Gives good corrosion resistance and can be used on Steel, Cast Iron, Light Alloys,...
Selemix 1-420 Polyurethane Thinner
For use with selected products in the Selemix range including Selemix 2K Polyurethane Direct Primer. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use Only
Selemix 6-540 Hammer Effect Additive
A silicone additive for Selemix solventborne cellulose, polyurethane and fast dry synthetic topcoats to achieve attractive Hammer Effect finishes. For use with: Selemix 7-610 and 7-611 Fast Dry Synthetic Topcoats Selemix 1K Cellulose Topcoats 7-510 Polyurethane Topcoat Selemix Direct Pro High Gloss (first coat must be sprayed without...