Watco Asphalt Paint Anti Slip (formerly Anti Slip Traffic Paint) is a flexible, anti-slip coating which transforms and brightens up asphalt, and offers a good degree of slip resistance with just one high build application.

Asphalt Paint Anti Slip contains a pre-blended aggregate which provides a finely textured slip resistant surface. It leaves a more uniform and easily cleaned finish than conventional anti slip coatings where grit is sprinkled on separately.

This abrasion resistant, waterproof coating is most suited for use in light to medium trafficked areas, private asphalt driveways, tennis courts, playgrounds and warehouses. Watco Heavy Duty Anti Slip Traffic Paint is available for heavier wear external areas.

Asphalt Paint Anti Slip is quick and easy to use for painting large areas, and ideal for highlighting hazards, marking out parking bays and pedestrian areas, and for using with Watco Stencils. This coating has excellent UV resistance which helps protect against fading.

Asphalt Paint Anti Slip carries CE Mark EN 1504-2 and has impressive test results for slip resistance, hardness, abrasion, adhesion, impact, and flexibility. It’s virtually solvent free and has an A+ VOC emissions rating.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Surface Preparation
• Application
• Test Results
• Standard Compliance
• Limitations

Features & Benefits

• Areas of use include:
• Pedestrian walkways
• Colour coding and highlighting hazardous areas
• Line marking
• Playgrounds
• Tennis courts
• Private asphalt driveways
• Anti-slip, flexible water-based acrylic
• Fine pre-blended grit offers slip resistance for pedestrians
• Transforms, dull, drab asphalt and tarmac
• Excellent resistance to UV and weathering
• Colours, protects, and waterproofs with just one coat
• High pigment level offers excellent hiding power
• Breathable
• Virtually solvent free and odourless – safe to use inside as well as outside
• Suitable for both asphalt and concrete
• Superior performance demonstrated by ISO testing to CE Mark EN1504-2

Surface Preparation

New asphalt & tarmac – should be sound and at least 3 months old. If any residual oils remain, the surface should be washed using Watco Concroff.

Existing bare asphalt & tarmac – remove any grease or oil deposits using Watco Concroff.

Painted surfaces – abrade to remove any weak or loose paint. Check remaining paint is well bonded. Very smooth, glossy paint should be lightly abraded to provide a key. Watco Bio D can be used to remove grease and oil from painted surfaces.

Bare concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff, again, flush with clean water and allow the surface to dry.

New concrete – as a guide, new concrete should be left for four weeks to dry in the summer and six in the winter. The surface should then be prepared using Watco Etch & Clean and thoroughly rinsed away and left to dry prior to applying this coating.

Damp surfaces – this coating can be applied to residual damp which may remain after cleaning, but not where there is rising damp.

Priming – one coat is generally sufficient. On very porous or open textured surfaces, two coats may be required. The first coat will act as a ‘priming coat’ and may be diluted with up to 10% water to assist with application.

Application

Stir the paint thoroughly and do not thin, however in very hot weather, (25°C+); up to 10% water may be added to make application easier.

Apply by roller and work well into the surface. It can be applied by brush but this may result in reduced coverage.

Avoid applying the paint too thickly as this encourages water to puddle on the surface and as such may become slippery.

If a second coat is required, apply it as soon as the first coat is dry (generally 6 hours), and within 5 days of applying the first coat. If more than 5 days elapse, the first coat should be lightly abraded before the second coat is applied. Avoid washing the surface for 7 days.

Test Results

• Abrasion Resistance ISO 5470-1 - 333mg
• Impact Resistance ISO 6272 - Class 3
• Scratch Resistance ISO 4586-2 - 7N
• Adhesion Test ISO 2409 - Class 0
• Adhesion Test EN 1542 - 3.3MPa/Nmm²
• Wolff-Wilborn Hardness Test - 7H
• Flexibility ISO 1519 - 2mm
• Gloss Value - 4
• Water Permeability EN 1062-3 - W₃
• Slip Resistance BS7976-2 - 52 PTV

Standard Compliance

• EN 1504-2
• BREEAM COMPLIANT
• VOC LEVEL 10g/litre (very low)
• ISO 16000
• REACH COMPLIANT

Limitations

Not recommended for use on concrete used by vehicles (see instead Watco Heavy Duty Anti Slip Traffic Paint).

Watco Anti Slip Traffic Paint is intended as a decorative finish only and will not bind or fill weak or defective asphalt surfaces.

Do not apply in areas which will be constantly under water. Do not apply too thickly. If the crevices and texture of the asphalt are filled with paint, this can prevent water draining which may result in a slip hazard.