- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
This product is temporarily unavailable; in the meantime, our technical team recommend Watco Concrex Sub Zero Floor Repair Mortar as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Rapid set concrete repair mortar for heavy wear, cold areas, that can be applied at 50mm thick at -20°C. Ideal for use in cold stores, securing railings, poles and posts, roads and manhole frames, etc.
- Easy to use – just add water, mix, and apply
- Starts to harden in 10 minutes, fully hard in five hours when suitably insulated (at -10°C)
- Takes forklifts in just 2 hours
- Allows essential maintenance even in freezing conditions
- Magnesium phosphate-based formula generates heat when mixed with water, allowing the product to be used as low as -20°C
- Non shrinking
Note: While great care is taken with the colour samples shown, no guarantee can be given that they represent exactly the colours offered.
Watco Flowpatch Sub Zero is a pre-mixed magnesium phosphate cement blended with specially selected aggregates, that will cure rapidly, even at -20°C and accept traffic after just 2 hours.
Ideal for repairing holes or levelling damaged concrete floors in freezer and chiller rooms. Also suitable for general external repairs in cold conditions.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use include:
- Cold stores
- Securing railings
- Poles and posts
- Roads and manhole frames etc
- Easy to use – just add water, mix and apply
- Starts to harden in 10 minutes, fully hard in five hours when suitably insulated (at -10°C)
- Takes forklifts in just 2 hours
- Allows essential maintenance even in freezing conditions
- Magnesium phosphate-based formula generates heat when mixed with water, allowing the product to be used as low as -20°C
- Non shrinking
Surface Preparation
Remove all loose material including dust, oil, and grease. Minimum application depth should be 20mm. Repair edges should be cut to depth to avoid feather-edging.
Dampen bare concrete with clean, cold water. Remove any standing water.
Briefly warm the area using a blowlamp or gas torch. This helps to accelerate curing.
Mixing
Mixing must be carried out in an ambient temperature above 5°C.
If mixing at temperatures below 5°C, pre-warm the mixing vessel with warm (approximately 25°C - 30°C) water.
Remove the bag of powder and pour 2 litres per 25kg or 0.8 litres per 10kg of clean, cold water into the plastic container. Gradually add all the powder, mixing thoroughly. Continue mixing to produce a smooth workable mortar. Do not mix the product for more than 4 minutes. Use immediately.
Application
Trowel Watco Flowpatch Sub Zero firmly into place using a steel trowel or float (available from Watco). The trowel can be wiped with clean, cold water to make finishing easier.
Apply the product at a minimum 20mm thickness, if using at a temperature range of -20°C to 5°C.
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Concrete
- Application Method
- Steel float or trowel
- Single, Two or Three Pack
- Single
- Pack Size
- 10KG
25KG - Coverage
- 10kg produces 4.6 litres of mortar. This covers approximately 0.24m2 when applied at 20mm thick
25kg produces approximately 11.5 litres of mortar. This covers 0.6m2 when applied at 20mm thick. - Recommended Thinner/Cleaner
- Remove excess with a cloth or scraper and wash with water before the product sets.
- Density
- 2200kg/m3
- Layer Thickness
- Minimum application depth should be 20mm
- Pot Life
- Approximately 5 to 10 minutes at 20°C, so do not mix at one time more than you can use within a few minutes.
- Fully Cured
- Fully hard in five hours when suitably insulated (at -10°C)
- Base Type
- Solvent-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Sand and Cement
- Application Method
- Trowel
- Product Usage Type
- Repair
- Product Range
- Watco Specialist
- Product Range
- Flowpatch
- Categorised As
- Repairs > Low Temperature Repair Mortars
- Seasonal
- Cold Weather
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Flowpatch Sub Zero Rapid Floor Repairs is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT