- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Primes and seals porous, dusty floors prior to painting, for use with Watco specialist polyaspartic coatings.
- Primes and seals porous, dusty floors prior to painting
- Can be used at -10°C to +25°C
- Ready to overcoat in 4 hours
- Superior performance demonstrated by ISO testing to CE Mark EN1504-2
- Use with the following Watco products: Cold Set Coating, Fastcoat, Food Safe Coating, Protecta-Coat, Safety Coat Cold Cure and Safety Coat Food Safe
Watco Polyaspartic Primer is a unique, two part resin that has been specially designed prior to using Watco’s range of polyaspartic coatings.
When applied by roller, Polyaspartic Primer primes and seals very porous or high suction surfaces, such as sand and cement screed, to ensure a uniform finish and help prevent air entrapment bubbles in the subsequent coating.
Polyaspartic Primer cures quickly and after just one hour it leaves a tacky finish which can then be overcoated.
This product can also be beneficial when overcoating an existing, well-bonded paint before using a Watco Polyaspartic coating as a top coat.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Surface Preparation
- Mixing
- Test Results
- Application
- Standard Compliance
- Limitations
Features & Benefits
- Use with the following Watco products:
- Cold Set Coating
- Fastcoat
- Food Safe Coating
- Protecta-Coat
- Safety Coat Cold Cure
- Safety Coat Food Safe
- Areas of use includes production areas, warehouses, showrooms, workshops and loading bays
- Cold stores, walk-in fridges and freezers
- Primes and seals porous, dusty floors prior to painting
- Can be used at minus 10°C to 25°C
- Ready to coat in 4 hours
- Superior performance demonstrated by ISO testing to CE Mark EN1504-2
Surface Preparation
Bare concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow surface to dry. For the removal of heavier deposits of oil and grease, Watco Concroff is recommended; again, flush with clean water and allow the surface to dry.
New concrete – as a guide, new concrete should be left for eight weeks to dry. The surface should then be prepared using Watco Etch & Clean and thoroughly rinsed away and left to dry prior to applying this primer.
Application in low temperatures – If applying in cold conditions the product should ideally be stored in a warm room at least 8 hours prior to use. Below 5°C it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient.
Mixing
Mix between 10°C and 25°C. Remove the two inner tins from the tall outer tin.
Stir each tin thoroughly and poor all of the contents into the outer tin, (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or similar wide bladed tool, (a piece of wooden batten is ideal). Continue mixing until an even consistency is obtained. Do not mix more than one pack at a time.
If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the side and bottom of the tin. Do not dilute.
Test Results
- Abrasion Resistance ISO 5470-1 - 361mg
- Impact Resistance ISO 6272 - CLASS 2
- Adhesion Test ISO 2409 - CLASS 0
- Adhesion Test EN 1542 - 3.0MPa/Nmm2
- Flexibility ISO 1519 - 2mm
- Gloss Value - 96
- Water Permeability EN 1062-3 - W3
Application
Apply between -10°C and +25°C. Empty the mixed components into a paint tray and apply to the floor using a microfibre roller, (not a medium pile or foam), ‘working out’ the primer into a thin paint film. A paint brush can be used for cutting in. Do not apply too thickly since this will result in reduced coverage.
Standard Compliance
- EN 1504-2
- BREEAM Compliant
- Medium VOC level (500g/litre)
- ISO 16000
- REACH Compliant
Limitations
Do not apply to damp surfaces.
Do not apply if rainfall is imminent.
Most self-levelling compounds cannot be painted – please ask for details.
Painting chequer paint can be a problem since coatings can wear prematurely off the ‘high spots’.
Data sheet
- Manufacturer
- Watco
- For Use By
- Professional Use
- Single, Two or Three Pack
- Two-Pack
- Minimum Applied Thickness
- 85 microns
- Coverage
- 25m2 per coat onto a non-porous surface.
10-15m2 onto a porous or textured surface.
If applying in temperatures below 0°C coverage may be reduced. - Recommended Thinner/Cleaner
- It is not practical to clean applicators and they should be discarded after use.
- Min. Application Temperature
- Air Temperature -10°C.
Floor Temperature -10°C. - Min. Application Temperature
- -10c
- Touch Dry
- -10°C: 16 hours
0°C: 8 hours
10°C: 4 hours
20°C: 2 hours - Recommended Dry Film Thickness
- 85 microns.
- Recommended Wet Film Thickness
- 100 microns.
- UN Number (Base)
- UN1263
- Suitable For Use On
- Wood
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Ceramic Tile
- Suitable For Use On
- Asphalt
- Suitable For Use On
- Previously Painted Surfaces
- Suitable For Use On
- Fibreglass
- Suitable For Use On
- Sand and Cement
- Suitable For Use On
- Metal
- Suitable For Use On
- Concrete
- Application Method
- Roller
- Components
- 2K
- Usages
- Low Temperature
- Product Usage Type
- Primer
- Product Range
- Watco Specialist
- Colour Family
- Clear
- Categorised As
- Floor Paints > Low Temperature Floor Primers
- Seasonal
- Cold Weather
- Product Type
- Polyaspartic
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Polyaspartic Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Watco Etch & Clean Concrete Surface Preparation
Dual action formula cleans and prepares bare concrete prior to painting. Use on old and new concrete, inside or outside Etches bare concrete to promote adhesion of paint finishes Removes dirt and light oil deposits Removes cement deposits from new concrete to ensure good paint adhesion Reduces alkalinity of new concrete – essential...
Watco Concroff Oil & Grease Remover
Lift grease and oil from bare concrete with this powerful, water-based degreaser. For preparation of heavily contaminated greasy floors prior to painting, inside or outside. Low odour formula Ideal for preparation to painting Removes oil and grease Can be diluted and used as a general floor cleaner on bare concrete Safe for use on most...
Watco Cold Set Coating
A polyaspartic coating for use at low temperatures - ideal for cold areas such as walk-in fridges, cold stores and loading bays. Highly wear resistant, easily copes with forklift trucks. Allows essential maintenance during the winter Ideal for use in chiller rooms Superior abrasion, scratch, and UV resistance Latest 2-part polyaspartic...
Watco Fastcoat
A new type of resin formulation significantly reducing time taken to paint a floor and put back into use. 5 colours available as well as an anti slip finish for a finely textured, easy clean surface. Revolutionary, high performance, two part, polyaspartic resin formulation Exceptionally fast curing - apply 2 coats in one day to reduce...
Watco Food Safe Floor Coating
A toughened two-pack floor coating designed for food preparation and storage areas and environments, including walk-in fridges. For use on concrete or sand and cement floors and asphalt Provided it is at least a month old and completely dry Can be used on most existing coatings, wood, metals and fibreglass although a sample area...
Watco Safety Coat Food Safe
A safety surface paint certified for use in food manufacturing and storage areas, with a fast-curing anti-slip coating. Meets requirements for EN14/3 (Food taint test) Excellent abrasion and UV resistance Can be applied at a temperature range of minus 10-30°C Note: While great care is taken with the colour samples shown, no guarantee...
Watco Protecta-Coat
Clear high-sheen gloss or non-slip finish that can be applied in cold conditions, as low as minus 10°C. Ideal for long term protection of epoxy and decorative floor finishes. For when conventional coatings will fail to dry. New type of resin formulation. Uses the latest polyaspartic technology for an exceptionally durable protective...
Watco Safety Coat Cold Cure
A new type of anti slip resin formulation that can be applied as low as minus 10°C. Most suited for use in heavily trafficked unheated areas such as workshops, warehouses, loading bays and cold stores. Two part, anti slip, polyaspartic resin formulation with easy clean, anti slip surface Superior performance demonstrated by ISO testing to...