A unique formula based on a blend of ceramic, ‘diamond hard’ wax and polyurethane resin, has produced a ‘Best in Class’ single pack paint for general use.

All grades now carry CE Mark EN 1504-2 and have impressive test results for abrasion, scratch-and-impact resistance, as well as for adhesion, hardness and flexibility.

All tests have been undertaken to ISO standard where applicable and demonstrated this ‘Best Ever Formulation’ to be four times more scratch resistant than previously, twice as hard wearing and with 50% improved adhesion.

This attractive, hardwearing coating is easy to apply and dries quickly to provide a low maintenance, tough, oil resistant finish.

Other versions available:

Matt Concrete Floor Paint helps to disguise imperfections in older floors and reduce reflection or glare. It’s still easy to keep clean and has all the benefits of the high gloss finish.

Watco Concrete Floor Paint Anti Slip provides a good level of slip resistance and the anti-slip particles are pre-blended which makes it easier to achieve a uniform finish.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Surface Preparation
• Mixing
• Test Results
• Application
• Standard Compliance
• Limitations

Features & Benefits

• Areas of use includes production areas, warehouses, and workshops
• Professional quality, single pack polyurethane coating
• Transforms and dustproofs drab, stained concrete
• Ideal for identifying production and storage areas and traffic aisles
• Easy to use and easy to keep clean
• Superior performance demonstrated by ISO testing to CE mark EN 1504-2
• High Gloss, Matt & Anti Slip versions available
• New formulations to 9 RAL colour shades
• Chemical resistant - resists short term spillages of oils, grease, diesel, and White Spirit

Surface Preparation

Bare Concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow the surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff, again, flush with clean water and allow the surface to dry.

New Concrete – as a guide, new concrete should be left for four weeks to dry in the summer and six in the winter. The surface should then be prepared using Watco Etch & Clean and thoroughly rinsed away and left to dry prior to applying this coating.

Priming – is not usually required, but for very porous high suction surfaces, such as sand and cement screed, use Watco 4 Hour Epoxy Primer. Concrete should be sufficiently porous to allow the paint to penetrate, so very smooth or power floated concrete is unsuitable unless first primed with Watco Powerfloat Primer.

Painted Surfaces – abrade to remove any weak or loose paint. Check remaining paint is well bonded. Very smooth, glossy paint should be lightly abraded to provide a key. Watco Bio-D can be used to remove grease and oil from painted surfaces. Watco Concroff is a very powerful degreaser for contaminated bare concrete, (do not use on a previously painted surface since it can soften paint).

Test Results

• Abrasion Resistance ISO 5470-1 - 361mg
• Impact Resistance ISO 6272 - CLASS 2
• Scratch Resistance ISO 4586-2 - 7N
• Adhesion Test ISO 2409 - CLASS 1
• Adhesion Test EN 1542 - 3.25MPa/Nmm²
• Wolff-Wilborn Hardness Test - 9H
• Flexibility ISO 1519 - 2mm
• Gloss Value - High Gloss 92, Matt 4
• Water Permeability EN 1062-3 - W₃
• Slip Resistance BS7976-2
• 28 PTV (Gloss)

Application

The paint should be thoroughly stirred and must not be thinned.

Apply by roller and work well into the surface. Use a paint brush for edges.

Avoid applying the paint too thickly.

The second coat can be applied as soon as the first coat is dry (generally 16 hours) and should be applied within 5 days. If more than 5 days elapse, the first coat should be lightly abraded before the second coat is applied.

Avoid washing the surface for 7 days.

Standard Compliance

• EN 1504-2
• BREEAM Compliant
• High VOC level (450g/litre)
• ISO 16000
• REACH Compliant

Limitations

This coating is not recommended for areas where cars may stand for long periods.

In common with single pack paints of this type, a reaction can take place between the car tyres and the paint, leading to delamination – in such cases we recommend a two-pack epoxy system such as Watco Epoxy Gloss Coat.

It is also unsuitable for most self-levelling compounds (please ask for details) and areas subject to rising damp.