- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Selemix 8-110/8-111 2K WB Acrylic Single Stage DTM Finish (Fast Curing)
2K fast curing, waterborne, acrylic coating with 6,700+ colours for direct application to well-prepared steel, galvanised steel, phosphate steel, or aluminium surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111). Standard curing version available here.
- Excellent gloss and colour retention and excellent hardness
- Recommended for high quality finishes in industrial agricultural equipment and machinery
- Product can be purchased as a Two Component Pack, or as Base or Hardener only
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- For Industrial Use Only
Please Note: This listing refers to 8-110 and 8-111 when used Direct To Metal. To use this product as a topcoat please see Selemix 8-110/8-111 2K WB Acrylic Topcoat (Fast Curing)
Product customisation
Don't forget to save your customization to be able to add to cartSelemix 8-110/8-111 2K WB Acrylic Single Stage DTM Finish (Fast Curing) is a 2K waterborne, acrylic coating, suitable for direct application to well-prepared steel, galvanised steel, phosphate steel, or aluminium surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111) please choose from the drop down menu above. Standard curing version available here.
It provides excellent gloss and colour retention and excellent hardness.
It is especially recommended for high quality finishes in industrial agricultural equipment and machinery.
This listing refers to 8-110 and 8-111 when used Direct To Metal. To use this product as a topcoat please see Selemix 8-110/8-111 2K WB Acrylic Topcoat (Fast Curing).
Please note: Other gloss levels are achievable when 8-110 and 8-111 Binders are combined - please contact our Technical Department before placing an order on 0113 2455450 (option 2) or send a message to [email protected] for details.
For Industrial Use Only.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Surface Preparation
- Mixing
- Application Notes
- Theoretical Coverage
- Drying Times
- Health & Safety
Features & Benefits
- 2K waterborne, acrylic coating
- Suitable for direct application to well-prepared steel, galvanised steel, phosphate steel, or aluminium surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use
- Available in High Gloss (8-110) and Matt (8-111)
- Excellent gloss and colour retention and excellent hardness
- Recommended for high quality finishes in industrial agricultural equipment and machinery
- Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
- *Note: RAL Pearl colours shown are approximations only - matches will not be exact
- For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel:
- Machine sand with P80-120 discs and degrease
Phosphated Steel:
- Abrade with Scotchbrite® and degrease
Galvanised Steel:
- Abrade with Scotchbrite® and degrease
Light Alloys:
- Machine sand with P280-320 discs and degrease
Aluminium:
- Machine sand with P280-320 discs and degrease
GRP:
- Machine sand with P280 discs and degrease
Painted Surfaces:
- Machine sand with P240-320 discs and degrease
Mixing
- Thoroughly mix paint before activating and check colour before use
Features | Conventional Spray 1st Coat | Conventional Spray 2nd Coat | Air Assisted Airless |
---|---|---|---|
By Weight: 8-110/8-111 Topcoat 9-125 Hardener Water - (Thoroughly mix topcoat for 5 minutes and then add:) |
By Weight: 1000 400 150 - 300 Water |
By Weight: 1000 400 150 - 300 Water |
By Weight: 1000 400 150 - 200 Water |
By Volume: 8-110/8-111 Topcoat 9-125 Hardener Water - (Thoroughly mix topcoat for 5 minutes and then add:) |
By Volume: 2.5 1 0.4-0.75 (15-30%) Water |
By Volume: 2.5 1 0.4-0.75 (15-30%) Water |
By Volume: 2.5 1 0.4-0.6 (15-20%) Water |
Viscosity (at 20°C): | 65-70 secs DIN4 | 55-60 secs DIN4 | 55-60 secs DIN4 |
Pot Life (at 20°C): | 2 hours | 2 hours | 2 hours |
Application Notes
Features | Conventional Spray | Air-Assisted Airless |
---|---|---|
Spraygun Setup: |
Nozzle: Gravity: 1.4-1.6mm Suction: 1.6-1.8mm Pressure feed: 0.8-1.0mm |
Nozzle: 04.132/ 05.152/05.172 |
Air Pressure: |
HVLP: 2 Bar Standard: 2-3 Bar |
Atomisation: 3-3.5 Bar |
Fluid Pressure: | N/A | Paint Pressure: 70-150 Bar |
Number of coats: |
1 Light dry + 1 full (1 visit) or: 1 light closed + 1 medium (2 coats) |
1 medium + 1 medium |
Flash-off between coats: |
2 mins minimum at 20°C (1 visit) or: 15-30 mins minimum at 20°C (2 coats) |
15-20 mins minimum at 20°C |
Drying: |
Air dry or bake at: 60°C for 30 mins |
Air dry or bake at: 60°C for 30 mins |
Flash-off before bake: | 20 mins minimum at 20°C | 15-20 mins minimum at 20°C |
Wet Film Thickness: | 125-150 microns | 125-150 microns |
Dry Film Thickness: | 60-80 microns | 60-80 microns |
Brush and Roller:
8-110/8-111 Acrylic Topcoat can be applied by brush (solvent resistant) or roller short haired mohair roller:
- Activate 2.5:1 with 9-125 Hardener
- Thinning with 10% of water is recommended
- Apply in 2 coats with minimum 45 minutes flash-off between coats
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
- 5 - 7 m² per litre at 70 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C | |
---|---|
Dust Free | 10-15 mins |
Touch Free | 2-3 hours |
Handleable | 6 hours |
Hard Dry | Overnight |
Stoving | 30 minutes @60°C (according to film thickness) |
Overcoating time |
Minimum: 8 hours Maximum: 24 hours without sanding on clean surface with itself |
Please Note: Lower temperature or film thickness higher than 80µm will extend drying times. The drying times quoted are approximate times and will vary depending on drying conditions and film thickness. Poor ventilation, temperature below 20°C, humidity above 85% RH and excessive film thickness will extend the drying times. |
Health & Safety
- For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
- THIS PRODUCT IS FOR INDUSTRIAL USE ONLY
Data sheet
- Manufacturer
- Selemix
- For Use By
- Industrial Use
- Interior / Exterior Use
- Interior & Exterior
- Water / Solvent Based
- Water Based
- For Use On
- Steel
Galvanised Steel
Phosphated steel
Aluminium - Sheen
- High-Gloss
Matt - Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- 2.5:1
- Application
- Spray
Brush
Roller - Touch Dry (at 20°C)
- 3 hours
- Pot Life (at 20°C)
- 2 hours
- UN Number (Base)
- N/A
- Hard Dry
- Overnight
- Dust Dry (at 20°C)
- 10-15 mins
- Colour(s)
- Fully Tintable
- Base Type
- Water-Based
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Steel
- Suitable For Use On
- Cast Iron
- Suitable For Use On
- Light Alloys
- Suitable For Use On
- Galvanised Steel
- Suitable For Use On
- Phosphated Steel
- Suitable For Use On
- GRP
- Suitable For Use On
- Compatible Existing Coatings
- Finish
- Matt
- Finish
- High Gloss
- Substrate
- Steel
- Substrate
- Galvanised Steel
- Substrate
- Aluminium
- Substrate
- Painted / Primed Metal
- Substrate
- GRP
- Substrate
- Light Alloys
- Substrate
- Phosphated Steel
- Usages
- Gloss Retention
- Usages
- Colour Retention
- Usages
- Force Dry Compatible
- Usages
- Stoving Compatible
- Usages
- Exterior Durability
- Usages
- Direct to Metal
- Usages
- High Corrosion Resistance
- Usages
- High Chemical Resistance
- Usages
- High UV Resistance
- Usages
- Process Efficiency
- Usages
- Low VOC
- Usages
- Chemical Resistance
- Usages
- Atmospheric
- Technologies
- Waterborne
- Technologies
- 2K
- Application Methods
- Conventional
- Application Methods
- Airmix
- Application Methods
- Electrostatic
- Product Type
- Acrylic
- Environment
- Atmospheric
- Environment
- Exterior Durability
- Touch Dry/Dust Free (@ 20-25°C)
- 3 hours
- Drying Properties
- Stoving Compatible
- Drying Properties
- Force Dry Compatible
- Product Attributes
- Gloss Retention
- Product Attributes
- Colour Retention
- Resistance to
- Chemicals
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Selemix 8-110/8-111 2K WB Acrylic Single Stage DTM Finish (Fast Curing) is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Selemix 8-110/8-111 2K WB Acrylic Topcoat (Fast Curing)
A fast-curing 2K waterborne, acrylic topcoat, suitable for use on primed or painted surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111). Standard Curing version available here. Excellent gloss and colour retention and excellent hardness Can be...
Selemix 8-110/8-111 2K WB Acrylic Single Stage DTM Finish
2K waterborne, acrylic coating, with 6,700+ colours for direct application to well-prepared steel, galvanized steel, phosphate steel, or aluminium surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111). Fast Curing version available here. Excellent...