- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Unique dustproofer, hardener and surface sealer combined - ideal for use in warehouses, production areas, garages, and storage rooms.
- Water-based acrylic
- Microporous formula allows surface to breathe
- Reduces staining and is easy to clean
- Suitable for general industrial use
- Dustproofs and seals in one coat, saving on downtime
- Ready for full use after 24 hours
Watco Concrete Sealer Water Based seals and hardens new and old bare, porous concrete floors and screeds. It is micro-porous, which allows the surface to breathe, and contains a micronised acrylic which penetrates deep into porous surfaces to bind, harden and seal.
The cross linking properties of the acrylic dries to form a surface film, providing a more stain resistant, easier to clean finish.
The appearance can vary from low sheen to gloss depending upon the porosity of the substrate and the number of coats applied.
It is quick and easy to apply and most suited for use in warehouses and production areas, or anywhere which would benefit from a penetrative, dustproof, virtually odourless sealer for medium trafficked areas.
Concrete Sealer Water Based is also available in a light grey finish, which both seals and tints the floor at the same time.
Concrete Sealer Water Based is breathable, virtually solvent free and safe for use in confined areas. It has an A+ VOC emissions rating with a very low VOC content.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use include:
- Warehouse
- Production Areas
- Garages
- Storage Rooms
- Clear, acrylic, water based sealer
- Also available in a light grey tinted version to both seal and add colour
- Penetrates, dustproofs and hardens in just one coat
- Single pack sealer – easy to apply
- Ready for full use after 24 hours
- Only one coat is generally needed saving on downtime
- Minimal darkening effect on most surfaces
- Breathable
- Virtually solvent free and low odour
- Glossy finish – stain resistant and easy to keep clean
Surface Preparation
Bare concrete – a good sweep and/or vacuum is often sufficient on a dusty surface.
For the removal of dirt, light oil and grease we recommend Watco Bio-D. Flush with clean water and allow the surface to dry. For heavier deposits, Watco Concroff, a very powerful degreaser, is recommended, again, flush with clean water and allow the surface to dry.
Concrete Sealer Water Based must be applied to a dry surface, not wet, however, if any residual damp remains as a result of cleaning, this is acceptable. Avoid wetting very porous surfaces since they will absorb too much water.
New concrete – as a guide, new concrete should be left for 4 weeks to dry in the summer and six in the winter.
Surface laitance should be removed by means of mechanical abrasion. If the surface is dirty, please clean as per the heading ‘Bare concrete’.
Priming – is not usually required, but for open textured, or very porous high suction surfaces, such as sand and cement, further coats may be required to seal the substrate and to provide a uniform finish.
Do not use on very smooth or power floated concrete, instead use Watco Powerfloat Sealer.
Application
Important – give the container a really good shake to disperse the pigment which may have settled during storage.
Pour a small amount of Concrete Sealer Water Based directly onto the floor and spread using a soft broom or brush, working it into the floor. It is important to spread it reasonably evenly to avoid an uneven finish.
If a stronger colour is required when using the tinted grey version, apply a second coat.
Standard Compliance
- BREEAM COMPLIANT
- VOC LEVEL 10g/litre (low)
- ISO 16000
- REACH COMPLIANT
Limitations
Do not apply to painted, sealed or power floated surfaces since Concrete Sealer Water Based relies upon penetration.
Do not apply to a wet surface - slight residual damp which may remain after cleaning is acceptable.
In areas where it is important to achieve a uniform, light grey tinted finish, we recommend applying a test patch as the colour can vary, particularly on very porous surfaces such as sand and cement screed.
Do not allow the product to puddle on the surface – any unabsorbed surface liquid should be completely removed.
Do not acid etch surfaces prior to using Concrete Sealer Water Based.
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior & Exterior
- Water / Solvent Based
- Water
- For Use On
- Concrete
- For Use On
- Concrete Floors
- Application Method
- Soft broom or brush
- Single, Two or Three Pack
- Single
- Pack Size
- 5L (Grey, Clear)
25L (clear only) - Minimum Applied Thickness
- 50 microns
- Coverage
- 40m2 -50m2 per 5L depending on the porosity of the substrate.
Textured or particularly porous surfaces, such as sand and cement screed, will greatly reduce the coverage. - Recommended Thinner/Cleaner
- Water
- Min. Application Temperature
- Air temperature 15°C
Floor temperature 10°C - Touch Dry
- 10°C 6 hours
20°C 4 hours
30°C 2 hours - Recommended Dry Film Thickness
- 50 microns
- Recommended Wet Film Thickness
- 100 microns
- UN Number
- N/A
- Dry to Recoat
- 10°C 8 hours
20°C 6 hours
30°C 6 hours - Base Type
- Water-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Sand and Cement
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Broom
- Components
- 1K
- Product Usage Type
- Sealer
- Product Range
- Concrete
- Dry for Light Traffic
- 10°C 12 hours
20°C 12 hours
30°C 12 hours - Dry for Heavy Traffic
- 10°C 24 hours
20°C 24 hours
30°C 24 hours - Colour Family
- Grey
- Colour Family
- Clear
- Product Type
- Acrylic
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Concrete Sealer Water Based is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Watco Bio-D Floor Cleaner
A heavy-duty biodegradable cleaner for floor preparation, removes grease and oil from painted or bare concrete. Low odour formula Ideal for preparation to painting Removes oil and grease Can be diluted and used as a general floor cleaner on bare concrete Safe for use on most painted surfaces More Information Delivery Info
Watco Powerfloat Sealer
Seals and protects power floated floors, specially formulated for smooth, power floated or glazed concrete. No need for expensive mechanical floor preparation Retains the attractive, smooth floor surface Tough, easy clean epoxy resin formulation Anti-slip version also available - excellent slip resistance Coverage Calculator See...