- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A toughened two-pack floor coating designed for food preparation and storage areas and environments, including walk-in fridges.
- For use on concrete or sand and cement floors and asphalt
- Provided it is at least a month old and completely dry
- Can be used on most existing coatings, wood, metals and fibreglass although a sample area should be tested first
- Meets requirements for EN14/3 (Food taint test)
- Rapid drying - 2 coats in a day, re-coatable in only 5 hours
- Can be applied at a temperature range of minus 10-30℃
- Excellent abrasion and UV resistance
- Hard-wearing chemical resistance
- Steam cleanable
- Can be applied in temperatures as low as -10℃
- Not for general or consumer use
Note: While great care is taken with the colour samples shown, no guarantee can be given that they represent exactly the colours offered.
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Watco Food Safe Coating uses the latest polyaspartic resin technology for a high quality, highly wear resistant coating that has been tested and has EN71/3 and taint test certification. It is ideal for normal food preparation environments as well as cold food storage areas such as walk-in fridges. It will cure in refrigerated areas (down to -10ºC) where other conventional paints will fail to dry.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use include:
- Food manufacturing and storage areas
- Cold food storage areas
- Tested to EN71/3 as a non-toxic product
- Takes heavy wear and tear
- Fast curing, re-coatable in only 5 hours
- Can be applied between -10℃ and 30℃
- Excellent chemical resistance
- Steam cleanable
Surface Preparation
All surfaces must be -10℃ or above and free from ice or water. Concrete to be treated must be at least four weeks old, completely dry and free of contaminants. Grease or oil should be removed with Watco Bio-D (or a similar emulsifying degreasant) and the area thoroughly washed off and allowed to dry.
Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Watco Etch & Clean to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Etch & Clean.
Watco Powerfloat Primer is recommended on powerfloated surfaces but it must be fully cured before overcoating.
Previously painted surfaces should be thoroughly abraded by sanding to improve adhesion and to remove any weak or loose material. A trial area is advisable to test compatibility with previous coatings.
Below 5℃ it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient.
Mixing
Mix between 10°C and 25°C. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin (scrape around the inside of the tins to remove any residue).
Mix the components together thoroughly using a spatula or a similar wide bladed tool (a piece of wooden batten is ideal). Continue mixing until an even colour and consistency are obtained. Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, use the spatula to blend in any unmixed material from the sides and bottom of the tin. Do not dilute.
Application
Apply between minus 10℃ and 30℃. The viscosity can become thicker at lower temperatures, reducing the coverage rates.
The product should be worked out with a short pile roller to maximise the coverage and get the best performance from the product.
Product Details
9299-947082
Data sheet
- Manufacturer
- Watco
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- Water / Solvent Based
- Solvent
- For Use On
- Wood
- For Use On
- Concrete
- For Use On
- Metallic Substrates
- For Use On
- Fibreglass
- For Use On
- Asphalt surfaces
- Application Method
- Short pile roller
Cut in using a brush - Single, Two or Three Pack
- Two-Pack
- Pack Size
- 2.5L
- Pot Life (at 20°C)
- 25 - 30 minutes at 15ºC.
Higher temperatures will reduce this time.
Pot life can be maximised by decanting mixed product into a shallow tray. - Coverage
- Approximately 25m² per coat per 2.5 litre unit.
The coverage will be reduced if the surface is textured or porous, or if the floor temperature is below 0ºC. - Recommended Thinner/Cleaner
- Watco Cleaning Solvent TH99 to remove splashes or clean tools before the product cures.
- Min. Application Temperature
- (-10°C)
- Min. Application Temperature
- -10°C
- Min. Application Temperature
- -10c
- UN Number
- N/A
- Resistance to chemicals
- resistant
- Resistance to chemicals
- 7 days
- Dry to Recoat
- -10°C 30 hours
0°C 36 hours
20°C 48 hours - Suitable For Use On
- Floors
- Suitable For Use On
- Asphalt
- Suitable For Use On
- Previously Painted Surfaces
- Suitable For Use On
- Fibreglass
- Suitable For Use On
- Asphalt Surfaces
- Suitable For Use On
- Sand and Cement
- Suitable For Use On
- Metal
- Suitable For Use On
- Concrete
- Suitable For Use On
- Wood
- Finish
- Mid-Gloss
- Application Method
- Roller
- Components
- 2K
- Usages
- Low Temperature
- Usages
- Hygienic Finish
- Product Usage Type
- Topcoat
- Dry for Light Traffic
- -10°C 16 hours
0°C 24 hours
20°C 6-8 hours - Dry for Heavy Traffic
- -10°C 48 hours
0°C 36 hours
20°C 12 hours - Colour Family
- Red
- Colour Family
- Yellow
- Colour Family
- Grey
- Colour Family
- Blue
- Categorised As
- Floor Paints > Low Temperature Floor Paints
- Seasonal
- Cold Weather
- Product Type
- Polyaspartic
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Food Safe Floor Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
You might also like
Watco Bio-D Floor Cleaner
A heavy-duty biodegradable cleaner for floor preparation, removes grease and oil from painted or bare concrete. Low odour formula Ideal for preparation to painting Removes oil and grease Can be diluted and used as a general floor cleaner on bare concrete Safe for use on most painted surfaces More Information Delivery Info
Price
£30.96
(incl. VAT)
In Stock and Available for Delivery
Watco Etch & Clean Concrete Surface Preparation
Dual action formula cleans and prepares bare concrete prior to painting. Use on old and new concrete, inside or outside Etches bare concrete to promote adhesion of paint finishes Removes dirt and light oil deposits Removes cement deposits from new concrete to ensure good paint adhesion Reduces alkalinity of new concrete – essential...
Price
£46.80
(incl. VAT)
In Stock and Available for Delivery
Watco Powerfloat Primer
An epoxy resin primer that allows smooth concrete to be painted without mechanical preparation. For priming power floated, very smooth or non-porous concrete floors which are prone to rejecting paint. Ready for overcoating in 12 hours Rapid version available, ready for overcoating in 4-6 hours Unique formula prevents paint peeling...
Price
£140.10
(incl. VAT)
In Stock and Available for Delivery