- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A safety surface paint certified for use in food manufacturing and storage areas, with a fast-curing anti-slip coating.
- Meets requirements for EN14/3 (Food taint test)
- Excellent abrasion and UV resistance
- Can be applied at a temperature range of minus 10-30°C
Note: While great care is taken with the colour samples shown, no guarantee can be given that they represent exactly the colours offered.
Product customisation
Don't forget to save your customization to be able to add to cartWatco Safety Coat Food Safe is a hard wearing, fast curing anti slip coating which has been tested to EN71/3 as a non-toxic product and has a Food Taint Test Certificate, making it ideal for busy food manufacturing or storage areas. It has excellent chemical resistant properties and can be steam cleaned if needed.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use include:
- Food manufacturing and storage areas
- Tested to EN71/3 as a non-toxic product
- Takes heavy wear and tear
- Excellent chemical resistance
- Steam cleanable
Surface Preparation
All surfaces must be -10℃ or above and free from ice or water.
Concrete to be treated must be at least four weeks old, completely dry and free of contaminants. Grease or oil should be removed with Watco Bio-D (or a similar emulsifying degreasant) and the area thoroughly washed off and allowed to dry.
Very smooth concrete or concrete with surface laitance (a weak dusty layer) should be abraded or etched with Watco Etch & Clean to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Etch & Clean.
Watco Powerfloat Primer is recommended on powerfloated surfaces but it must be fully cured before overcoating.
Previously painted surfaces should be thoroughly abraded by sanding to improve adhesion and to remove any weak or loose material. A trial area is advisable to test compatibility with previous coatings.
Below 5℃ it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient. Do not apply outside if rainfall is imminent.
Mixing
Mix between 10°C and 25°C. Stir each tin thoroughly and pour all of the contents into the outer tin (scrape around the inside of the tins to remove any residue).
Mix the components together thoroughly using a spatula or a similar wide bladed tool. Add the tin of anti slip aggregate. Continue mixing until an even colour and consistency are obtained.
Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the sides and bottom of the tin. Do not dilute.
Application
Apply between minus 10℃ and 30℃. Empty the contents into a roller tray and apply to the floor using a short pile roller, ‘working out’ the coating into a thin film. The viscosity will be somewhat thicker at very low temperatures, reducing coverage a little.
Most self levelling compounds cannot be painted - please ask our technical team for details on 0113 2455450 (option 2) or send a message to [email protected].
Data sheet
- Manufacturer
- Watco
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior & Exterior
- Water / Solvent Based
- Water
- For Use On
- Wood
- For Use On
- Concrete
- For Use On
- Metallic Substrates
- For Use On
- Fibreglass
- For Use On
- Asphalt surfaces
- Application Method
- Short pile roller
Cut in using a brush - Single, Two or Three Pack
- Three-Pack
- Pack Size
- 2.5L
- Pot Life (at 20°C)
- 25 - 30 minutes at 15ºC.
Higher temperatures will reduce this time.
Pot life can be maximised by decanting mixed product into a shallow tray. - Coverage
- Approximately 25m² per coat per 2.5 litre unit.
The coverage will be reduced if the surface is textured or porous, or if the floor temperature is below 0ºC. - Recommended Thinner/Cleaner
- Watco Cleaning Solvent TH99 to remove splashes or clean tools before the product cures.
- Min. Application Temperature
- (-10°C)
- Min. Application Temperature
- -10°C
- UN Number
- N/A
- Resistance to chemicals
- resistant
- Dry to Recoat
- 0°C 16 hours
20°C 4-5 hours - Base Type
- Water-Based
- Suitable For Use On
- Wood Floors
- Suitable For Use On
- Food Processing Plants
- Suitable For Use On
- Food Production Areas
- Suitable For Use On
- Storage Areas
- Suitable For Use On
- Metal
- Suitable For Use On
- Food Manufacturing
- Suitable For Use On
- Concrete
- Suitable For Use On
- Wood
- Suitable For Use On
- Floors
- Suitable For Use On
- Asphalt
- Suitable For Use On
- Previously Painted Surfaces
- Suitable For Use On
- Fibreglass
- Suitable For Use On
- Asphalt Surfaces
- Suitable For Use On
- Sand and Cement
- Suitable For Use On
- Factory Floors
- Suitable For Use On
- Metal Floors
- Suitable For Use On
- Asphalt Floors
- Finish
- Textured Gloss
- Application Method
- Roller
- Components
- 3K
- Usages
- Low Temperature
- Usages
- Hygienic Finish
- Product Usage Type
- Topcoat
- Product Range
- Safety Coat
- Dry for Light Traffic
- 0°C 24 hours
20°C 6-8 hours - Dry for Heavy Traffic
- 0°C 36 hours
20°C 12 hours - Colour Family
- Red
- Colour Family
- Yellow
- Colour Family
- Grey
- Colour Family
- Blue
- Anti-Slip Texture
- Fine Texture
- Categorised As
- Floor Paints > Low Temperature Floor Paints
- Categorised As
- Floor Paints > Low Temperature Anti-Slip Floor Paints
- Seasonal
- Cold Weather
- Product Type
- Polyaspartic
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Safety Coat Food Safe is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Watco Etch & Clean Concrete Surface Preparation
Dual action formula cleans and prepares bare concrete prior to painting. Use on old and new concrete, inside or outside Etches bare concrete to promote adhesion of paint finishes Removes dirt and light oil deposits Removes cement deposits from new concrete to ensure good paint adhesion Reduces alkalinity of new concrete – essential...
Watco Powerfloat Primer
An epoxy resin primer that allows smooth concrete to be painted without mechanical preparation. For priming power floated, very smooth or non-porous concrete floors which are prone to rejecting paint. Ready for overcoating in 12 hours Rapid version available, ready for overcoating in 4-6 hours Unique formula prevents paint peeling...