- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Watco Oil Block Primer is a two part epoxy primer specially developed to aid adhesion to porous floor surfaces that have become soaked with oil. It is suitable for concrete, brick and masonry and it will also work on timber surfaces. It is not suitable for use on non porous, previously painted surfaces or metal surfaces.
Grease and oil should be removed from the surface of a floor before priming, using a degreaser. The Watco Oil Block Primer then works by penetrating the surface with solvent, sealing in soaked-in oil contamination. This also helps to bind together weaker surfaces.
Watco Oil Block Primer is intended for mineral oil residues such as motor oil or cutting oils. It is not usually suitable for vegetable, animal or synthetic oil residues.
Watco Oil Block Primer is intended to be overpainted with epoxy floor coatings, but it can be used with many types of floor coatings.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use include:
- Machine workshop floors
- Factory and warehouse floors
- Garage floors
- Aids adhesion to porous floor surfaces that have become soaked with oil
- Penetrates the surface with solvent, sealing in soaked-in oil
- Binds together weaker surfaces
- Can be overpainted with epoxy floor coatings (except water based epoxy paints)
Surface Preparation
Remove as much oil as possible by scraping or grinding.
Clean the surface with a degreasant such as Watco Concroff. It is important to rinse all traces of the cleaner away and allow the surface to dry. If using a solvent based cleaner, follow the supplier’s instructions but, again, all traces should be removed before applying Watco Oil Block Primer.
Mixing
Open the inner tins carefully and pour all of the contents of both the resin and curing agent tins into the clean, empty outer tin. Mix thoroughly with a wide bladed stirrer such as a wooden batten or better still, use a Watco Paint Mixer. Scrape the bottom and sides thoroughly to ensure no unmixed material remains. Decant the mixed product into another vessel (or a paint tray, if applying by roller) and apply to the prepared surface.
Application
Do not apply at temperatures below 10°C.
Apply one good coat of Oil Block Primer to the prepared surface and allow it to dry. Application by brush is preferable, because it allows the primer to be worked into the surface, but if applying by roller, use a medium pile roller, working it backwards and forwards to encourage penetration into the surface.
Limitations
Watco Oil Block Primer can enable a successful floor coating under conditions of deep seated oil contamination that would otherwise be difficult to prepare thoroughly, but it should not be seen as a substitute for good preparation.
It is not suitable for use on non porous, previously painted surfaces, or metal surfaces. It is intended for mineral oil residues – not usually suitable for vegetable oil residues.
Do not overcoat with floor coatings that will be softened by oil, such as conventional single pack floor paints or most water based acrylic paints.
Watco Oil Block Primer will not provide a wearing surface – it requires overcoating with a suitable floor coating.
Contains solvent. Use only in well ventilated areas.
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior Use
- Water / Solvent Based
- Water
- For Use On
- Wood
- For Use On
- Concrete
- For Use On
- Brick
- For Use On
- Masonry
- Application Method
- Medium pile roller
Cut in using a brush - Single, Two or Three Pack
- Two-Pack
- Pack Size
- 4L
- Coverage
- 15m² - 20m² per 4 litres
- Recommended Thinner/Cleaner
- TH99 Cleaner/Thinner
If using inexpensive brushes or rollers, it may not be economical to attempt to clean them – it is usually better to allow the product to harden and dispose of them. - Min. Application Temperature
- 10c
- Touch Dry
- approximately 2 - 3 hours
- UN Number (Activator)
- UN1263
- UN Number (Base)
- UN1263
- Pot Life
- 5 hours
- Dry to Recoat
- After 16 hours but within 24 hours.
If more than 24 hours has elapsed, the primed surface should be abraded to provide a key. - Hard Dry
- 16 hours. Lower temperatures will extend curing times.
- Base Type
- Solvent-Based
- Suitable For Use On
- Timber
- Suitable For Use On
- Concrete
- Suitable For Use On
- Brick
- Suitable For Use On
- Floors
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Garage Floors
- Suitable For Use On
- Warehouse Floors
- Suitable For Use On
- Factory Floors
- Suitable For Use On
- Workshop Floor
- Suitable For Use On
- Masonry
- Application Method
- Roller
- Components
- 2K
- Usages
- Oil Resistant
- Product Usage Type
- Primer
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Oil Block Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Watco Concroff Oil & Grease Remover
Lift grease and oil from bare concrete with this powerful, water-based degreaser. For preparation of heavily contaminated greasy floors prior to painting, inside or outside. Low odour formula Ideal for preparation to painting Removes oil and grease Can be diluted and used as a general floor cleaner on bare concrete Safe for use on most...
Watco Application Tools & Accessories
Applications tools, equipment, and accessories for use with Watco paints, coatings, repair products, and fixings. More Information Delivery Info