- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Watco Basics Pourable Repair Mortar is a quick and easy way to fill holes in concrete floors. This blended polymer and cement formulation is strong enough to resist heavy foot traffic, trolleys and trucks. Just take as much powder as you need out of the bucket, mix with water and pour – you don’t need a primer.
- Just mix with water and pour
- Takes traffic after only 4 hours
- Non dusting, resists grease and oil
- Repairs from 5mm to 100mm thick in one go
For areas where there is regular forklift traffic, see Watco Flowpatch.
The product ‘flows’ to fill the hole making it unsuitable for ramps, steps or broken concrete edges; please see Watco Concrex for this type of repair.
Watco Basics Pourable Repair Mortar is a quick and easy way to fill holes in concrete floors. This blended polymer and cement formulation is strong enough to resist heavy foot traffic, trolleys and trucks; (for areas where there is regular forklift traffic, see Watco Flowpatch). Just take as much powder as you need out of the bucket, mix with water and pour – you don’t need a primer.
The mortar will not shrink as it dries and will take foot traffic after only 4 hours and trucks and trolleys after 6 - 8 hours. The product ‘flows’ to fill the hole making it unsuitable for ramps, steps or broken concrete edges; please see Watco Concrex for this type of repair.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use:
- Damaged, reasonably level concrete
- Indoors & outdoors
- Just mix with water and pour
- Takes traffic after only 4 hours
- Non dusting, resists grease and oil
- Repairs from 5mm to 100mm thick in one go
Preparation
Only basic preparation is necessary. If the hole or patch to be repaired is just dirty and dusty, give it a good sweep. Watco Basics Floor Cleaner can be used to remove oil and grease, or grease and loose material can be removed from small patches using a stiff broom or wire brush.
Application
- It does not matter if the floor has been left damp following any wet preparation
- Dampen dusty, porous surfaces with water in hot, dry conditions
- The mortar can be applied at any thickness between 5mm and 100mm. For deeper holes build up in layers, allowing the first layer of 100mm to dry for 12 hours
- If the edge of the repair is less than 5mm deep, chip some concrete away so that the edge of the mortar repair will be 5mm thick. For feather edge repairs which go to nothing please see Watco Concrex
- Remove the bag of powder from the Pourable Repair Mortar bucket
- The mix is 1 part water to 4 parts powder
- Only mix as much as you can use in 15 minutes. A cup can be used to measure the parts of water and powder
- Put the water into the plastic bucket
- Gradually add the powder mixing continuously. We recommend a mixing blade fitted into an electric drill. The ratio of water to powder is not critical, you just want the mix to be a consistency which can be poured. If it looks too runny add more powder, or too stiff, more water
- Once you’ve stopped mixing and started using the product do not re-mix it
- Immediately pour into the hole using a trowel to ‘help’ smooth the mortar into place
Application
- Not recommended on slopes, steps or broken concrete edges
- Resists oils and grease but not chemicals (see Watco Concrex)
- Do not use at temperatures below 5°C. Watco Flowpatch Sub Zero is for cold weather repairs
- It can be applied up to 100mm. For deeper holes build up in layers, allowing the first layer of 100mm to dry for 12 hours
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- For Use On
- Concrete
- Application Method
- Pour, trowel
- Single, Two or Three Pack
- Single
- Pack Size
- 25KG
- Maximum Applied Thickness
- 100mm. For deeper holes build up in layers, allowing the first layer of 100mm to dry for 12 hours.
- Coverage
- 25kg covers 0.5m2 at 25mm thick.
- Min. Application Temperature
- 5°C
- Shelf Life (from date of manufacture)
- 12 months in unopened containers.
- Resistance to chemicals
- Grease
- Resistance to chemicals
- Oil
- Dry for Light Traffic (at 20°C)
- 4 hours
- Base Type
- Solvent-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Concrete Floors
- Application Method
- Trowel
- Product Usage Type
- Repair
- Product Range
- Watco Basics
- Product Range
- Basics
- Dry for Heavy Traffic
- 6 - 8 hours @ 15°C - 20°C
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Basics Pourable Repair Mortar is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Watco Flowpatch Sub Zero Rapid Floor Repairs
This product is temporarily unavailable; in the meantime, our technical team recommend Watco Concrex Sub Zero Floor Repair Mortar as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt...
Watco Flowpatch Quick Setting Pourable Repair Mortar
Quick setting, pourable repairs for filling holes in heavily trafficked concrete floors, inside and out. Ideal for filling deep holes before screeding with Watco Flowtop. Flowpatch and Flowpatch Coloured Easy to use rapid dry formula Takes forklifts in just 2 hours Just add water, mix and pour Fibre reinforced for added strength...