- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total (inc. VAT) £0.00
Line marker with 180 semi-gloss colours for use in heavy wear areas or areas subject to chemical spillage. Not recommended for exterior use. It is a brush applied, two part epoxy resin marking paint with excellent resistance to abrasion and harsh chemicals.
- Can be applied to bare concrete or well bonded paint
- Cures to receive light traffic next day
Note: While great care is taken with the colour samples shown, no guarantee can be given that they represent exactly the colours offered.
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use:
- Heavy wear areas
- Areas subject to chemical spillage
- Safe traffic routes on floors
- Highlighting hazards such as step edges
- Can be applied to bare concrete or well bonded paint
- Cures to receive light traffic next day
- Virtually solvent free and virtually odourless
Surface Preparation
All surfaces should be clean and dry before application.
On painted or sealed surfaces remove any poorly bonded material and abrade well bonded paint or sealer to provide a key. A trial area is recommended on smooth, shiny surfaces to test adhesion.
Edges of lines should be defined with masking tape.
Mixing
Thoroughly stir the contents of the smaller resin tin before emptying it into the larger curing agent tin. It is very important that all the contents of the resin tin are decanted and thoroughly mixed with the curing agent with a wide bladed tool until an even colour is obtained.
Application
Best results are achieved in warm (minimum 15°C), dry conditions with good air circulation.
In very high temperatures (30°C and above) it is recommended that bare concrete is lightly dampened first with water.
Ideally use a brush and apply sufficient paint to obliterate the substrate. Do not over brush.
Remove masking tape 1 to 2 hours after painting.
After normal industrial use, worn line markings can be renewed with a fresh coat of Epoxyline. Lightly abrade the surface to provide a key and clean the area as per Surface Preparation section above.
Limitations
Not suitable for exterior use – it will fade. For step edges subject to very heavy wear a coating will have a limited life, and an alternative such as Watco Safety Edge GRP (in anti-slip fibreglass) may be more suitable.
Avoid washing the surface for 7 days after painting. Thereafter Watco Epoxyline will be resistant to the normal range of industrial cleaners, but strong degreasants should be tested first. Do not steam clean or expose to temperatures above 60°C.
Product Details
9333-1004590
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- For Use On
- Bare concrete or well bonded paint
- Application Method
- Brush
- Sheen
- Semi gloss
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 1L
- Pot Life (at 20°C)
- Up to two hours. Higher ambient temperatures will reduce the working life of the mixed components.
- Coverage
- Each pack will cover approximately 50m of 50mm wide line (2.5m²) per 1 litre allowing for one coat
- Recommended Thinner/Cleaner
- Brushes should be washed in warm soapy water before the product starts to cure. Accidental splashes of the resin component prior to mixing with the activator can only be removed by strong solvents.
- Min. Application Temperature
- 15c
- Shelf Life (from date of manufacture)
- 24 months in unopened container
- Resistance to chemicals
- Petrol
- Resistance to chemicals
- Oil
- Resistance to chemicals
- Cleaning Products
- Fully Cured
- Will normally cure overnight (at 20°C) to accept light foot traffic or a second coat (if needed) next day. It will be fully cured and have full chemical resistance in 7 days (at a minimum temperature of 15°C).
- Colour(s)
- Standard Colours
- Base Type
- Water-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Floors
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Previously Painted Floors
- Suitable For Use On
- Previously Painted Surfaces
- Suitable For Use On
- Warehouse Floors
- Suitable For Use On
- Factory Floors
- Suitable For Use On
- Workshop Floor
- Application Method
- Brush
- Components
- 2K
- Product Usage Type
- Lines
- Product Range
- Epoxy
- Colour Family
- Yellow
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Epoxyline is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage