- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Formerly known as "Protega HT600" - a heat resistant, silicone resin based single pack finish suitable for all types of manifold and exhaust systems.
- Good heat resistance properties up to 500℃ depending on quality, intermittent heat resistance up to 600℃
- Good petrol and oil resistance
- Good performance in salt spray and humidity testing
- Good adhesion over suitable zinc silicate primers
ViterTherm HT600 HR Finish, suitable for all types of manifold and exhaust systems.
Quick Links - Click To Jump To Section:
Technical Data
Data | |
---|---|
Volume Solids | Matt Black - 22 ± 2% |
Silver - 15 ± 2% | |
VOC Content | Matt Black - 650 + 20 g/litre |
Silver - 717 + 20 g/litre | |
SG | Matt Black 0.91-0.93 kg/lt |
Silver 1.04-1.06 kg/lt | |
Flash Point | 23-60℃ |
Film Thickness Range and Coverage
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
---|---|---|---|
Minimum | 10 µm | 50 µm | 20.0 m2/litre |
Maximum | 15 µm | 75 µm | 13.3 m2/litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Drying Times
Applied to 15 microns DFT | 23℃ |
---|---|
Flash Off | 5 - 10 min |
Air Dry | Touch Dry - 20 min |
Hard Dry - 4 hr | |
Force Dry | 30 min @120-150℃ |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Preparation and Application
Surface Preparation
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
- Pre-treatment improves adhesion and reduces corrosion under the paint film. Consult Axalta Coating Systems to check your pre-treatment process is suitable
Mix thoroughly before use.
Application Conditions
Only apply in conditions of good ventilation which must be maintained during drying and curing.
Do not apply when rain, mist, sleet or snow are imminent.
During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3℃ above the dew point. Paint temperature should ideally be at a minimum of 15℃.
Application Methods
By conventional spray
- Airless spray: not recommended as over-application is likely
- Conventional spray: thin to 20 - 30 seconds BSB4 cup @25℃ for conventional spray
Notes
- A film thickness of 10-15µm is recommended. Do not exceed 25 microns dft or blistering of the film on heating will result
- Apply in a single coat, overcoating is not recommended
Data sheet
- Manufacturer
- Axalta Coating Systems
- For Use By
- Professional Use
- Interior / Exterior Use
- Exterior Use
- For Use On
- Metal
- Application Method
- Spray
- Sheen
- Matt
Semi-Gloss - Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Coverage
- 13.3 - 20m2/litre
- Recommended Thinner/Cleaner
- 950 Thinner
- Min. Application Temperature
- 15ºC
- Solids by Volume
- Matt Black - 22 ± 2%
Silver - 15 ± 2% - Heat Resistance (up-to)
- 600°C
- VOC
- Matt Black - 650 + 20 g/litre
Silver - 717 + 20 g/litre - Touch Dry
- 20 min (23ºC)
- Recommended Dry Film Thickness
- 10 - 15 µm
- Recommended Wet Film Thickness
- 50 - 75 µm
- UN Number
- UN1263
- Hard Dry
- 4 hours (23ºC)
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Finish
- Semi-Gloss
- Finish
- Matt
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Product Range
- ViterTherm
- Colour Family
- Black
- Colour Family
- Metallic
- Colour Family
- Silver
- Heat Resistance
- Up To 600°C
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterTherm HT600 HR Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta Thinner General Industrial TH004
Use Axalta Thinner General Industrial TH004 (formerly known as Axalta Thinner No. 7) to thin and clean related Axalta products, such as Plicote HB Finish.
Axalta 950 Thinner
Axalta 950 Thinner, for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...