- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Super FG is a pre-mixed magnesium phosphate cement blended with specially selected aggregates. The resulting mix produces a mortar which gives rapid setting and high early strength properties suitable for works carried out in raising or lowering carriageway frames and covers.
Repairs can be carried out on concrete surfaces and with the speed of hardening; these may be brought into early use. The chemical mechanism will continue at temperatures down to 0°C thus enabling repairs to be carried out on floor areas in cold stores. Using suitable protection cold store area repairs may be carried out at temperatures down to –20°C.
The mixed mortar, when placed, will harden in approximately 10 minutes. The compressive strength gain will reach between 15N/mm2 and 23N/mm2 within 3/4 hour depending on the mix design used.
Super FG is a self contained product only needing to be mixed with water on site to produce a firm mortar. The addition of further water will produce a grout. Addition of aggregate to the grout will produce a workable concrete. The product is chloride free and can be safely used with cast iron and steel units. The mortar can be placed in sections of 8mm to 50mm in thickness and greater thicknesses can be built up in layers. After placement no special curing is required in moderate ambient conditions.
Epoxy Putty has been tested in accordance with the relevant parts of the following standard:
- BS 6319
Quick Links - Click To Jump To Section:
Features & Benefits
- Pre-mixed magnesium phosphate cement blended with specially selected aggregates
- Rapid setting and high early strength properties
- Suitable for works carried out in raising or lowering carriageway frames and covers
- Will continue at temperatures down to 0°C thus enabling repairs to be carried out on floor areas in cold stores
- Using suitable protection cold store area repairs may be carried out at temperatures down to –20°C
- Non-flammable
- Each 25kg pack will yield approximately 11.5 litres of mixed material at mortar consistency
Typical Grout Properties @ 20°C
Compressive Strength
Mortar, water content 1.5 litres per 25kg Super FG
3/4 Hour | 2 Hours | 7 Days | 28 Days |
---|---|---|---|
15N/mm2 | 25N/mm2 | 48N/mm2 | 55N/mm2 |
Grout, water content 2.25 litres per 25kg Super FG
3/4 Hour | 2 Hours | 7 Days | 8 Days |
---|---|---|---|
14N/mm2 | 24N/mm2 | 33N/mm2 | 375N/mm2 |
Concrete, water content 2.0 litres per 25kg Super FG
3/4 Hour | 2 Hours | 7 Days | 28 Days |
---|---|---|---|
13N/mm2 | 23N/mm2 | 34N/mm2 | 37N/mm2 |
- Density: 2200kg/m3
- Shrinkage: Volume stable
- Bond strength – slant shear: 40N/mm2
Instructions For Use
Preparation
Laitance and all loose material including dust, oil and grease should be removed in order to produce a sound substrate. The work area should be pre-wetted taking care to remove any standing water.
Mix Designs
The water requirement for each 25kg bag of Super FG to attain the designed consistency is:-
- Mortar consistency 1.50 to 1.75 litres
- Grout consistency 2.00 to 2.25 litres
- Concrete mix 1.75 to 2.00 litres
To use as concrete add 10kg of 10mm pea shingle (avoid limestone) to each 25kg bag of Super FG.
Mixing
Excess mixing water should not be used. When mechanical mixing is used wet down the mixing vessel then drain all free water. Add the measured quantity of mixing water. Add the full bag of Super FG. Mix for at least one minute. Suitable mixers include a slow speed high torque drill and Mortar Stirrer.
For mixing at temperatures below 5°C, pre-warm the mixing vessel with warm water and use warm mixing water. Suitable water temperatures are approximately 25-30°C.
Placing And Setting Frames
Place the mixed mortar as soon as mixing is complete. The chemical setting of Super FG is rapid and all mixed material should be placed within 10 minutes of adding the mixing water. Set frames by “the drop bed method” or by shimming with hard ceramic tiles to line and level followed by “mortar packing”.
The mortar should be fully compacted to obtain maximum strength. In both methods the mortar may be face finished using normal steel trowelling. Once the frame has been set, the outer area can be filled to the required thickness using Super FG as either a grout or concrete mix.
Curing
No special curing is required at temperatures between 5°C and 35°C. For placing temperatures outside this range contact the Technical Service Department. The reinstatement of the road surfaces may be undertaken within one hour of placing. The road may be opened to vehicular traffic within two hours of placing.
Data sheet
- Manufacturer
- Sika
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Steel
Iron
Concrete
Blockwork - Application Method
- Trowel
- Single, Two or Three Pack
- Single
- Pack Size
- 25KG
- Coverage
- Each 25kg pack will yield approximately 11.5 litres of mixed material at mortar consistency
- Size
- 25KG
- UN Number
- N/A
- Suitable For Use On
- Blockwork
- Suitable For Use On
- Iron
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Application Method
- Trowel
- Manufacturer
- Sika
- Components
- 1K
- Usages
- Concrete Repair
- Product Usage Type
- Bedding Mortar
- Product Range
- Parex
- Categorised As
- Repairs > Low Temperature Bedding Mortars
- Seasonal
- Cold Weather
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Sika Parex Super FG is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT