Jotun Conseal Touch-Up Alu is a one component physically drying acrylic coating with a matt finish for suitably prepared steel and coated surfaces. This version of Jotun Conseal Touch-Up is aluminium pigmented for improved barrier effect.

Jotun Conseal Touch-Up Alu is a high build product which is fact drying, with the product being touch dry from approximately 20 minutes at 23°C. It is ideal for use as a topcoat in atmospheric environments and can be applied at sub-zero temperatures.

Jotun Conseal Touch-Up Alu is recommended as a protective coating for refineries, power plants, bridges and buildings and it is suitable for a wide range of industrial structures.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Product Data
• Film Thickness
• Surface Preparation
• Application
• Drying & Curing Time
• Heat Resistance
• Product Compatibility
• Storage & Shelf Life
• Caution
• Health & Safety

Features & Benefits

• Aluminium pigmented version of Jotun Conseal Touch-Up for improved barrier effect
• One component physically drying acrylic coating
• High build product
• Fast drying - the product is touch dry after approx. 20 minutes at 23°C
• Can be used direct to metal
• Used as topcoat in atmospheric environments
• It can be applied at sub zero surface temperatures
• Recommended as a protective coating for refineries, power plants, bridges and buildings
• Suitable for a wide range of industrial structures

Product Data

The provided data is typical for factory produced products, subject to slight variation depending on colour.

Film Thickness

Surface Preparation

To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.

Please refer to the Application Guide (AG) for full details.

Application

Application Methods:

• Spray: If airless spray is used the paint must be diluted 5-10 %
• Brush: Use a suitable brush, care must be taken to achieve the specified dry film thickness
• Roller: May be used, but is not recommended for first coat on bare metal - care must be taken to achieve the specified dry film thickness

Please refer to the Application Guide (AG) for full details.

Product Mixing:

• Single pack

Pot Life:

• 1 hour @ 23°C

Thinner/Cleaning Solvent:

• Thinner: Jotun Thinner No. 7

Guiding Data for Airless Spray:

• Nozzle tip (inch/1000): 17-23
• Pressure at nozzle (minimum): 150 bar/2100 psi

Drying & Curing Time

• Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product
• Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness
• Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks, imprints or other physical damage
• Dry to over coat, minimum: The recommended shortest time before the next coat can be applied

Heat Resistance

Peak temperature duration max. 1 hour

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures.

Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat resistance

Product Compatibility

Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below.

Previous Coat:

• Acrylic, epoxy, zinc epoxy, shop primer

Subsequent coat:

• Acrylic

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.

Storage & Shelf Life

Shelf life at 23 °C

• Conseal Touch-Up Alu - 48 Months

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection.

Caution

• This product is for professional use only
• The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation
• Applicators and operators shall use appropriate personal protection equipment when using this product
• This guideline is given based on the current knowledge of the product
• Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work

Health & Safety

• Please observe the precautionary notices displayed on the container
• Use under well ventilated conditions
• Do not inhale spray mist
• Avoid skin contact
• Spillage on the skin should immediately be removed with suitable cleanser, soap and water
• Eyes should be well flushed with water and medical attention sought immediately

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.