Quick Links - Click To Jump To Section:

   
• Features & Benefits
• Substrate Preparation
• Application
• Limitations

Features & Benefits

   
• Applied cold in complete safety, without using flames
• Highly flexible; simple, quick and easy to apply
• Adheres perfectly to substrates
• With the use of Mapethene Primer W and Plastimul Primer SB it may be applied at low temperatures and on slightly damp substrates
• Vulcanized side strip to improve water-tightness at overlaps
• Good crack-bridging properties once applied
• Impermeable up to a pressure of 8 bar
• Preformed membrane; more control on its thickness during production and total uniformity of the mix
• Mapethene LT membranes are impermeable to radon and methane.
• Self-adhesive preformed bitumen waterproofing membrane made from a special mixture of bitumen
  admixed with polymers
• When bonded to high-strength HDPE film, it forms an impermeable sheet resistant to tearing
• The special mixture used to make Mapethene LT allows the product to be applied in the winter at temperatures as low as
  -5°C
• In hot weather, use Mapethene HT, which has a special bitumen mix that has been specifically developed for
  application in hot conditions and is just as easy to apply

Substrate Preparation

• Mapethene LT may be applied on concrete, solid bricks and vibro-compressed concrete blocks
• Substrates must be flat, sound and clean
• Remove cement laitance, loose and crumbling parts and traces of dust, grease and form release agents with high pressure water jets and wait until all the water has dried off. Completely remove all traces of any old waterproofing layers
• If the reinforced cement structure to be waterproofed has gravel clusters or other irregularities, remove them by hand or power tools or by hydro-demolishing
• Carefully clean any exposed pieces of rebar, treat them with a coat of Mapefer 1K anti-corrosion cementitious mortar and fill all gaps and demolished areas with Planitop Smooth&Repair R4 quick-setting, compensated-shrinkage, thixotropic cementitious structural mortar or a suitable product from the Mapegrout line of mortars
• For application on the surface of bricks or blocks, on the other hand, completely remove all traces of mortar protruding from between the blocks, skim over any defects and grout any gaps in the joints with Mapegrout 430 fine-textured thixotropic mortar or Mapewall Render & Strengthen high strength, natural hydraulic lime-based rendering and masonry mortar
• Then blend in all the corners between the foundations and walls and between adjacent vertical walls with the same products recommended to repair the surfaces and round off any sharp edges or corners
• Seal structural joints with Mapeband TPE tape bonded to the substrate with Adesilex PG4 epoxy adhesive broadcast with Quartz 0.5
• After preparing the substrate as specified, apply a coat of Mapethene Primer, one-component, solvent-free bitumen emulsion
• As an alternative at low temperatures, it is also possible to use Mapethene Primer W one-component, readymixed primer or Plastimul Primer SB high performance, quick-drying, solvent-based bitumen primer
• The consumption rate for these types of primer varies according to the absorbency of the substrate and is generally around 150-200 g/m²

Application

• Any through objects on horizontal and vertical substrates must be sealed using two pieces of Mapethene LT cut to shape to form a collar between the object passing through the surface and the substrate
• When applying the membrane on horizontal surfaces, remove the first 20 cm of silicone film, line up the roll in the direction it is to be applied and unroll the Mapethene LT
• Remove the film as you unroll the membrane so that it adheres evenly to the substrate
• Joints between adjacent rolls and pieces of membrane must overlap by at least 5 cm and the vulcanized strip along the outer edge of the Mapethene LT will help guarantee the seal even further
• Line up the membrane on the HDPE film on the roll of membrane already applied, remove the protective strip from the vulcanized strip and bond the next roll of membrane
• Make sure the joints between the pieces of membrane are staggered and carefully go over the overlaps with a rubber roller
• When applying the membrane on vertical surfaces, we recommend cutting Mapethene LT according to the height of the surface to be waterproofed
• Remove around 30 cm of silicone film, line up the sheet according to the direction it is to be applied and bond it to the substrate starting from the highest point
• Then apply the Mapethene LT, making sure there is an overlap of at least 5 cm, as when applying the membrane on horizontal surfaces
• To prevent damaging the upper edge of the membrane, we suggest applying Mapeband SA self-adhesive butyl tape with alkali-resistant, non-woven fabric backing between the Mapethene LT and the substrate
• Carry out localised repairs to areas that have been accidentally damaged with pieces of Mapethene LT cut from the roll of membrane
• Clean hands with lukewarm water and tools with water or thinners
• Within 48 hours of applying Mapethene LT, protect all waterproofed surfaces with a protective drainage membrane, such as Polyfond Kit Drain made by Polyglass S.p.A., which protects Mapethene LT when holes and trenched are filled in

Limitations

Do not use Mapethene LT in the following cases:

• During rainy weather
• On substrates with condensation or free-standing water on the surface
• Without a protective layer if exposed to direct mechanical loads
• Transport and store Mapethene LT vertically